Related Manuals for Kenwood KMD-D400
Summary of Contents for Kenwood KMD-D400
- Page 1 KMD-D400 3 DISC AND 1 DISC MD AUTO CHANGER INSTRUCTION MANUAL © B64-1426-00 (E) (MC) 00/3 2 1 99/12 11 10 9 8 7 6 5 4 3 2...
-
Page 2: Table Of Contents
• If the unit starts to emit smoke or strange Installation Procedure..............10 smells, turn off the power immediately and Connections ................11 consult your Kenwood dealer. Installation ...................11 • Make sure not to get your fingers caught Troubleshooting guide ..........13 between the faceplate and the unit. - Page 3 If the unit faceplate and the unit. still does not operate normally after a while, consult your Kenwood dealer. • During installation, do not use any screws except for the ones provided. The use of improper screws might result in damage to the main unit.
- Page 4 Safety precautions IMPORTANT INFORMATION • Do not leave the MD in the unit for a prolonged period. The ejected MD should be This unit is NOT designed to be connected placed in an MD case for storage. directly to control units that are manufactured •...
-
Page 5: Operations Buttons And Display
Operations Buttons and Display Release button MENU indicator DEMO indicator Title display 3 MD CHANGER + 1 PLAYER KMD-D400 24BIT RESOLUTION MENU D/A CONVERTER DISP Disc No. indicator DISC indicator DASC 11BAND DIGITAL AUDIO MINI DISC SPECTRUM ANALYZER DISP button MD Slot Spectrum analyzer display Opration indicator... -
Page 6: Md Changer Play
Operations MD Changer Play Disc No.3 being played: the indicator blinks To set MDs in the main unit: To store an MD: Press one of the 01 - 03 buttons for at least one second. Insert the first MD in the MD slot. The MD currently set in the play position will be stored in the The first MD is set in the play position. -
Page 7: Plus-One Md Play
Plus-one MD play Switching Spectrum Analyzer Display Even when three MDs have been set in the main unit, a further You can select the display to enjoy sounds with eyes. MD can be played as the plus-one MD. Operation for "N" Setting: To play a plus-one MD (a fourth MD): Each time you press the DISP button, the spectrum analyzer display switches as follows;... -
Page 8: Menu Systems
Operations Menu System Table of Adjustment Mode To accommodate a greater number of functions, a function set Adjustment Operation of Control button system has been employed for making settings. Press the mode DISC+ button DISC- button DISP button to enter the function set mode and then display (Display) the function to make the setting. -
Page 9: Theft Deterrent Faceplate
Reattaching Faceplate: Theft Deterrent Faceplate Hold the faceplate so that the The faceplate of the unit can be detached and taken with you, operation face faces the front helping to deter theft. toward you and press until it locks. The faceplate will be set Removing Faceplate: and the unit will be operational. -
Page 10: Accessories
Accessories Installation Procedure The O-N switch should be set according to the control unit in External view External view use as well as to the connected models..Number of items ..Number of items When the centre unit is compatible with the "N"-operation, set the O-N switch to "N". -
Page 11: Connections
Connections Installation Centre unit Installation Firewall or metal support Control input Accessory2 White/Black – FRONT • L White Bend the tabs of the mounting sleeve with Gray/Black a screwdriver or – similar utensil and Metal mounting strap Self-tapping attach it in place. FRONT •... - Page 12 Installation Removing the Unit Removing the hard rubber frame Refer to the section “Removing the hard rubber frame” and Engage the catch pins on the removal tool and remove the two then remove the hard rubber frame. locks on the lower level. Lower the frame and pull it forward as shown in the figure.
-
Page 13: Troubleshooting Guide
Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM POSSIBLE CAUSE SOLUTION The disc control mode cannot No cable has been connected to the disc changer input Connect the control cable to the disc changer input terminal be selected. - Page 14 Troubleshooting Guide The following messages are displayed on the centre unit when certain problems are occurring in your system. Take the recommended actions. The faceplate of this unit has been removed. NO PANEL ] Replace it. E-30 Nothing has been recorded on the MD. BLANK ] The next MD will automatically be played.
-
Page 15: Specifications
Specifications Specifications subject to change without notice. MD player section General Laser diode ............GaAlAs ( =760 nm) Operating voltage ......14.4 V (11 – 16 V allowable) Digital filter (D/A)........8 Times Over Sampling Current consumption ............0.8 A D/A Converter..............24 Bit Installation size (W D) ......182 154 mm Frequency response (±1 dB) ........5 Hz –...