Yamaha Clavinova CLP-480 Owner's Manual page 79

Message
Maximum no. of devices
exceeded
Memory full
Move to?->
Name?->
No device
No device (media)
No file
No response
from USB device
Notice:
Protected Song
Overwrite?->
Please wait
Protected device (media)
Protected Song
Remaining space
on drive is low
Selected drive?->
Set?->
Song error
Song too large
Start?->
Sure?->
The number of USB storage devices exceeds the limitation. Up to two USB storage devices can be
connected simultaneously. For details, see page 51.
Since the capacity and the number of files of MEMORY drive/USB storage device are full, the
operation cannot be made. Delete some Songs in the MEMORY drive/USB storage device or move
Songs to another USB storage device, and try again.
This message prompts you to select the Move destination. Follow the instructions in "Moving files"
on page 45.
This message prompts you to change the name of the Song/folder which is currently displayed.
Follow the instructions in "Renaming files" (page 43) or "Making folders in the USB storage device"
(page 45) to change the name, or press the B [– (NO)] button to cancel.
A USB storage device was not connected to the instrument when you attempted to perform a
device-related operation. Connect the device, and try again.
No media is not has been inserted to the selected USB storage device. Insert the media.
This message appears when there is no backup file to load in the connected USB storage device.
The instrument cannot communicate with the connected USB device. Redo the connection (page
51). If you still see this message, the USB device may be damaged.
This message appears when you attempt to handle the Protected Song. For information on the
limitation of file operations, see page 41.
The file already exists. This message prompts you to overwrite the existing data with new data. Press
the B [+ (YES)] button to proceed, or press the B [– (NO)] button to cancel.
The instrument is processing the data. Wait until the message disappears, then go on to the next
step.
This message appears when you attempt a file operation (page 41), record your performance or
save the data on a read-only USB storage device. Cancel the read-only setting, if possible, and try
again. If you still see this message, the USB storage device is internally protected (such as
commercially available music data). You cannot make the file operation or record your performance
to such a device.
You attempted a file operation to a Protected Song or read-only file. Data of those types have
handling limitations (page 41), and also cannot be used for editing (page 37). Use a read-only file
after cancelling the read-only setting.
Since the remaining space on the MEMORY drive/USB storage device is low, delete any
unnecessary files (page 43) before recording.
This message prompts you for confirmation to continue the operation with the currently selected
USB storage device. Press the Press the B [+ (YES)] button to proceed, or press the B [– (NO)]
button to cancel.
This message prompts you to save the settings. Press the B [+ (YES)] button to save, or press the
[EXIT] button to cancel.
This message appears, if a problem is found with the Song data when you select a Song or while the
Song is playing. In this case, reselect the Song, and try again to play back. If the message still
appears, the Song data may have been damaged.
The size of Song data (MIDI/Audio) exceeds the limitation. The following causes can be considered.
• The Song size you attempt to play back exceeds the limitation. The limitation for playback is
approx. 550KB (MIDI), 80 minutes (Audio).
• The Song size exceeds the limitation during recording. The limitation for recording is approx.
550KB (MIDI), 80 minutes (Audio). The recording will end automatically and the recording data
before the end is saved.
• The Song size exceeds the limitation during converting a MIDI Song to an Audio Song. The
limitation is 80 minutes (Audio).
This message prompts you to start the operation. Press the B [+ (YES)] button to start, or press the
[EXIT] button to cancel.
This message prompts you for confirmation of the operation. Press the B [+ (YES)] button to execute,
or press the B [– (NO)] button to cancel.
Meaning
Appendix
79
Message List