Page 1
Use & Care Guide Ice Maker Guia de Uso y Cuidado Máquina de hielo Guide d’utilisation et d’entretien Machine à glaçons 241927600 November 2007...
You can register online at www.electroluxusa.com or by dropping your Product Registration Card in the mail. Please record the purchase date of your Electrolux unit and your dealer’s name, address and telephone number. ________________________________________...
Model EI15IM55GS can be installed using a gravity drain or the Electrolux EIMP60, optional drain pump kit. Follow these guidelines when installing drain lines to prevent water from flowing back into the ice...
EIMP60 drain pump. The Electrolux EIMP60 drain pump is available through your Dealer, or direct from Electrolux with complete installation instructions. If a pump other than the Electrolux EIMP60 drain pump is to be used, it must meet the following specifications: •...
(see REVERSING THE DOOR). All units require zero clearance when installed flush with a cabinet or wall (see Figure 2). Electrolux stainless steel models require a minimum 2-3/4 inch handle clearance when installed against a wall or cabinet that extends beyond the front edge of the unit (see Figure 3).
However, make certain that the tubing is not pinched or damaged during installation. • Electrolux recommends the use of copper tubing for installation. DO NOT use plastic water supply line since it may crack or rupture with age and may cause water damage to your house.
(see Figure 10). CHECK LEVEL Figure 10 If the ice maker is not level, adjust the feet on the corners of the unit as necessary (see Figure 11). TURN FOOT TO ADJUST Figure 11...
Door Reversal Reversing the Door (some models) All Electrolux units may be left or right hand opening. The door opening is easily reversed by moving the hinge hardware to the opposite side (see Figure 12). Figure 12 To reverse the door:...
Page 11
Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge (see Figure 17). Figure 17 DOOR CLOSER INSERTS BOSS Remove existing bottom hinge (3 screws) and remount on opposite side TOP. Remove hinge screw pin.
Door Adjustment Adjusting the Door Your door is aligned at the factory before shipment. Occasional re-adjustment may be necessary, especially if an overlay panel is installed. The following procedure will correct for up to 1/4” alignment. The door should never be flush with the top of the cabinet.
Built-In Installation / Start-Up Installing a Built-In Your Electrolux product has been designed for either free-standing or built-in installation. When built-in, your ice maker does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed.
Ice Cube Thickness Your Electrolux ice maker uses advanced technology to make ice that is crystal clear. This technology cascades a flow of water over a chilled ice mold that is mounted vertically so no water sits in it.
ARROW button to lower the setting to thin the ice bridge. IMPORTANT Ice thickness adjustment should only be made one increment at a time. Allow ice maker production to stabilize for 24 hours before rechecking ice thickness. Touch and release the LIGHT button key to exit the ice thickness adjustment mode.
Discoloration from chlorine gas is normal. Follow exterior cleaning instructions. Interior Cleaning - As Required Disconnect power to the ice maker. Open the door and remove any ice from the storage bin. Wipe down the interior and storage bin with a solution of non-abrasive mild soap or detergent and warm water.
Wear rubber gloves and safety goggles and/ or face shield when handling Ice Machine Cleaner. CAUTION Use only Electrolux Ice Machine Cleaner (part number EIM30046). It is a violation of Federal law to use this solution in a manner inconsistent with its labeling.
Page 18
The display will show “CL” to confirm the beginning of the cleaning cycle. When water begins to flow over the evaporator (approximately 3 minutes), add one package of Electrolux Ice Machine Cleaner to the water reservoir. FRONT COVER When ice production resumes, the water fill valve will energize, fill the water reservoir, and shut- off after three minutes.
Pour one gallon of cool, fresh water into the ice bin. The water should drain freely. If your ice maker is equipped with a drain pump, the pump should drain the ice bin. WATER...
Troubleshooting Before You call For Service If the unit appears to be malfunctioning, read through Normal Operation first. If the problem persists, check the Troubleshooting Guide. Locate the problem in the guide and refer to the cause and its remedy before calling for service.
Troubleshooting – What to check when problems occur Problem Possible Cause Poor ice quality (soft or unclear). Poor incoming water quality. Ice-making system is dirty. Unit produces shallow or Low water level. incomplete cubes, or the ice fill Hot incoming water. pattern on the evaporator is incomplete.
State of Alaska) In the U.S.A., your appliance is warranted by Electrolux Home Products, Inc. We authorize no person to change or add to any of our obligations under this warranty. Our obligations for service and parts under this warranty must be performed by us or an authorized Electrolux Home Products, Inc.