Motorola WS2000 Installation Manual

(2)
socket-outlet.
accessible easily an near equipment position in, plugged be to needs that equipment
equipment.
to accessible easily and nearby socket the sources—install power uninterruptible
specifications. operation equipment
meet temperatures ambient that and device the around ventilation adequate
exist. can surges power where conditions
or thunderstorms during circuits power its with work or equipment this install
spaces. lit dimly in circuits power equipment with work
overloaded.
not is and power required the provide can grounded, is unit the for circuit power
equipment.
the of operation the during times all at accessible is connector power
device. the to cords power approved only
protection. overload appropriate have circuits power connecting
grounded. and wired properly is unit this to connected device any that
circuit. electrical grounded and wired properly
power all Connect source. power the to connecting before grounded is unit
secured. and mounted appropriately not was that equipment from
can injury bodily or device the to Damage mountings. its from away break and
to equipment the cause can that way a in install not do and anchored are racks that
allowances. weight and dimensions appropriate with racks in equipment this
equipment. this installing while etc.) necklaces, watches, (rings, jewelry any
source. power its to system the connecting before installation,
equipment correct Verify reports. survey site and instructions installation
equipment. this install should personnel qualified and trained
accidents preventing for practices standard review Also, device. the of use and
with associated hazards any for document this review equipment, any operating
Warnings
Introduction
The WS2000 Wireless Switch provides centralized management of wireless network
components across a wired network infrastructure. This wireless switch can connect directly
to a cable or DSL modem, and can also connect to other wide area networks through a Layer 2
or 3 device (such as a switch or router).
Product Description
AC Power Connection
Serial Port
CompactFlash Slot
Power LED
Clear Face Plate
Rubber Plug for
CompactFlash Slot
4 LAN (RJ-45) Ports 2 LAN (RJ-45) Ports
WAN Port
With Power Without Power
The WS2000 Wireless Switch has the following features:
• One WAN port for connection to a DSL modem, cable modem, or any other Layer 2/3
network device.
• Six LAN ports—four ports provide 802.3af Power over Ethernet (PoE) support, the other
two do not provide power. Each port has two LEDs, one indicating the speed of the
transmission (10Mbits/sec. or 100Mbits/sec.), the other indicating whether there is
activity on the port.
• A serial port for direct access to the command-line interface from a PC. Use a DB-9 female
to female null modem cable to connect to this port.
• A CompactFlash® slot provides administrative functions.
(3)
(1)
Guide Installation Quick WS2000 • slot
bezel and bracket
rack for screws Mounting bezel Rack • (4)
bracket Rack • (4)
For •
(4) mount wall for anchors Wall #6 •
the
(4) bracket wall for screws mounting #6 •
Verify •
bracket mount Wall •
KT-MTG-WS-2000-WW) or (KT-MTDP-WS-2000-WW
Verify •
Separately) (Sold
weather Box Accessories Mounting
not Do •
following: the contain
not Do •
sales your to items damaged or missing any report
the Verify •
the Verify •
perform. or correct to attempt
Attach •
Motorola- only that procedure or condition dangerous
Verify •
Verify •
damage. equipment or loss data cause can cautions Disregarding
a to cords
the Verify •
occur
requirements special
over tip
Verify •
document the throughout used are that
Install •
Remove •
all Read •
survey site from derived documentation site-specific
Only •
site- detailed For instructions. installation site-specific
the during use to guidelines and procedures, specifications,
installation
networking LAN-based Ethernet basic with familiar is
Before
Wireless WS2000 the installing for responsible technician
Technical Specifications
Physical Specifications
Width 286mm (11.26in.)
Height 45mm (1.75in.)
Depth 203mm (7.99in.)
Weight 0.64kg (1.41lbs)
Power Specifications
Operating Voltage 48VDC
Operating Current 1A, Peak Current 1.6A
Environmental Specifications
Operating Temperature 0°C to 40°C (32°F to 104°F)
Storage Temperature -40°C to 70°C (-40°F to 158°F)
Operating Humidity 10% to 85% Non-condensing
®
Storage Humidity 10% to 85% Non-condensing
Operating Altitude 2.4km (1.49mi)
Storage Altitude 4.6km (2.86mi)
Installation
The WS2000 can operate in various locations, allowing placement in most environments. Basic
installation steps entail the following:
®
1. Snap clear face plate (in WS2000 main box) onto the front-right side of the switch.
2. Select a site (desk, wall, or rack) for installation of the wireless switch.
3. Install in selected location using the instructions specifically for that location type.
Connect the wireless switch to the power supply early in the installation process
for easy access to the connector; however, do not plug the power supply into a
power source before installation is complete.
4. Plug the wireless switch into the wall power socket.
5. Lock device to desk, wall, or rack using lock port on the switch.
6. Plug in WAN and LAN (Access Port) connections.
7. Configure the product for your network and devices (see the WS2000 Wireless Switch
System Reference available on the Motorola website).
(4)
Guide Installation Quick WS2000 •
CompactFlash® for plug Rubber •
installed) (already
housing of bottom for plugs Rubber •
option mount desk for feet Rubber •
(1) cable patch CAT-5 Ethernet •
cord line with supply Power •
plate face snap-on Clear •
Switch Wireless WS2000 •
Box Switch Wireless WS2000
should packages The representative.
and contents package the Inspect
Contents Package Verifying
should personnel trained
potentially a Indicates
required. is Care
and hints tips, Indicates
conventions icon following the Note
Conventions Document
analysis. network site and
the see procedures installation specific
give not does It process. installation
provides guide This concepts.
technician the that assumes It Switch.
the assist to intended is guide This
Installer the To
Selecting a Site for Installation
The WS2000 can be installed on a flat surface, a wall, or in a rack. When selecting a site, the
installer should verify the location has access to:
• A grounded outlet—preferably one that has surge protection or is protected by an
uninterruptible power supply (UPS)
• The WAN connection for the switch (whether a modem, router, switch, or hub).
(The wireless switch comes with a 6ft. (1.829m) patch cable for this purpose, but the
installer is not required to use either that cable or stay within that distance.)
• The LAN connections for this switch (whether access port, switch, hub, or computer).
Ensure this location meets optimal temperature and environmental requirements for the
operation of this device (see Technical Specifications).
Desk Mounting
The desk mount option uses rubber feet which allow the unit to sit on most flat surfaces.
The four (4) round rubber feet can be found in the WS2000 (main) box in a separate plastic bag.
1. Turn the switch upside down so the side with the power connector is facing up.
2. Connect the power supply to the switch as shown in diagram.
Do not attach the power supply to the wall outlet until installation of the switch
is complete.
3. Remove the backings from the four (4) rubber feet and stick them to the switch on the four
circles, as shown. The feet will be right next to the four plugs.
Spain
00 40 324
Spain
00 40
4375
5-520-1835
6074-49020
580
1-505-5794-0
+65-6796-9600
Guide Installation
905-629-7226
Switch Wireless
WS2000
will they
your contact
your run
4. Return the switch to the upright position in the place that you wish it to sit, ensuring that
it is sitting evenly on all four rubber feet.
5. Connect the power supply to the wall outlet.
Wall Mounting
The wall mount bracket option secures the unit to most walls using the four screws included
in the mounting accessories box. The wall mounting accessories are sold separately from the
switch (KT-MTDP-WS-2000-WW or KT-MTG-WS-2000-WW).
1. Remove the protective rubber plugs from the switch as shown.
2. Using the screws and wall anchors supplied in the mounting accessories box, attach the
wall mount bracket to the wall as shown.
Power Plug Connector
Rubber Plugs
(5)
2007 May A Revision
72-100065-01
http://www.motorola.com
IL60196 SCHAUMBURG,
ROAD ALGONQUIN E 1303
INC. MOTOROLA,
7360 945 118 +44 Operations Distributor
call or distributor local Contact Europe/Mid-East
US Outside +1-954-255-2610 Support Sales
US Inside 1-800-347-0178 America Latin
Outside
91 +34 84452900 Sweden/Sverige
Inside
324 91 Spain/España 11-8095311 Africa South
2232 +47 Norway/Norge 315-271700 Netherlands/Nederland
Mexico/México 2-484441 Italy/Italia
Germany/Deutschland 01-40-96-52-21 France
5407 9 Finland/Suomi 7020-1718 Denmark/Danmark
Austria/Österreich 1-800-672-906 Australia
Asia/Pacific 2424 328 0800 Kingdom United
1-631-738-2400
Canada 1-800-653-5350 States United
Center: Support Motorola the contact
equipment, the with problem a is there If Support. Systems or Technical facility's
equipment, your using or unit your running problem a have you If applications.
and network facility's the in operate to configured be must it unit, the using Before
Information Service
To snap into the wall mount bracket, the protective rubber plugs must be removed.
Align the RJ-45 ports on the switch with the embossed port symbols on the front
of the wall mount bracket.
Wall
Embossed
Port Symbols
(6)