1. Manuals
  2. Brands
  3. Electrolux Manuals
  4. Vacuum Cleaner
  5. Z4700 Series
  6. Owner's manual

Electrolux Z4700 Series Owner's Manual

Electrolux upright vacuum cleaner owner's guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Upright Vacuum Cleaner
Owner's Guide
Household Type
Z4700 Series
IMPORTANT
Please read these
instructions for
advice on the
maintenance of
your cleaner.
FILTER REPLACEMENT CODE: EF86b
IMPORTANT INFORMATION
2 – 4
GUARANTEE
4
QUICK REFERENCE
5
HOW TO ASSEMBLE
5 – 8
HOW TO USE
9 – 1 0
ROUTINE MAINTENANCE
11
Empty Dust Cup
11
Clean Dust Cup Filter
11
PERIODIC MAINTENANCE
12
Brushroll
12
Brushroll Belt
12
PROBLEM SOLVING
13 – 1 5
Clear Hose
13
Thermal Cut Off
13
Mini Turbo Nozzle
14
www.electrolux.co.uk

Advertisement

Table of Contents
loading

Related Manuals for Electrolux Z4700 Series

Summary of Contents for Electrolux Z4700 Series

  • Page 1 Upright Vacuum Cleaner Owner’s Guide Household Type Z4700 Series IMPORTANT Please read these instructions for advice on the maintenance of your cleaner. FILTER REPLACEMENT CODE: EF86b IMPORTANT INFORMATION 2 – 4 GUARANTEE 4 QUICK REFERENCE 5 HOW TO ASSEMBLE 5 – 8 HOW TO USE 9 – 1 0...

  • Page 2: Important Safeguards

    Use only as described in this manual. Use only manufacturer’s recommended attachments. • Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service centre before using.

  • Page 3: Before You Start

    2. Examine the mains supply cable for damage (only after removing the plug from the socket outlet). 3. If the supply cord is damaged it must be replaced by a Electrolux Service Agent or similar qualified person in order to avoid a hazard.
  • Page 4 The guarantee may be invalidated by unauthorised repair or modification of the appliance. d. You may be charged by Electrolux if you call for an engineer to resolve a problem that we believe is covered in the instruction booklet.

  • Page 5: Quick Reference

    Quick Reference Wand Crevice Tool Dusting Brush Hose Base Dust Cup with Lid and Filter Handle ( Turbo Handle) Tool Caddy Rear Housing Hose Retainer Stair Brush How To Assemble CAUTION: Assemble the cleaner completely before using. NOTE: All screws must be installed to properly secure the parts of the vacuum.
  • Page 6 How To Assemble Step 1: Assemble the rear housing by sliding it on top of the base and attaching to the base using a long screw provided Step 2: Attach the tool caddy housing by sliding it onto the housing, lining up the screw holes, and then attaching it using the 2 short screws provided.
  • Page 7 How To Assemble Step 4: Secure the hose assembly connection on the rear housing (FIG. 4). Step 5: Thread the hose inside the lower hose retainer and then attach the lower hose retainer to the rear housing with a short screw Step 6: Pull the electrical cord up to the cord retainer and firmly push into the retainer (FIG.
  • Page 8 How To Assemble Step 7: Then wrap the hose up and over the hose hook on the handle as shown. Plug the end of the hose into the hose retainer hole on the base and then snap the hose into the hose holder on the tool caddy .

  • Page 9: How To Use

    How To Use CAUTION: Do not plug in cleaner until you understand all controls and features. Plug in Vacuum (FIG. 10). Unwrap the cord by turning the quick release cord hook (FIG. 10a), unwind the cord and plug into an appropriate outlet.

  • Page 10: Stair Cleaning

    NOTE: When using on hard floors an additional hard floor nozzle is available. Please ring Electrolux Customer Care on 08706 055 055. Call to this number will be charged at 5p per minute at all times from a BT Landline.

  • Page 11: Routine Maintenance

    NOTE: Turn off the switch and unplug the electrical cord before routine maintenance. Never operate the vacuum cleaner without the dust cup filter in place. Empty Dust Cup Lift up the latch and pull out to release the dust cup from the housing.

  • Page 12: Periodic Maintenance

    Step 10: Rotate brushroll to position belt on brushroll pulley. Step 11: Replace the hood. Step 12: Tighten screws. NOTE: Use only GENUINE ELECTROLUX replacement brushroll belt, Code ZE090. FIG. 19 FIG. 20 PLEASE NOTE: The new belt will be...

  • Page 13: Thermal Cut-Off

    The cleaner should turn on. Step 7: If the cleaner still does not operate, please call Electrolux Customer Care on 08445 614614. Calls to this number will be charged at 5p per minute at all times from a BT Landline.

  • Page 14: Maintenance Instructions

    Models equipped with Mini Turbo Nozzle (on some models) A Mini Turbo Nozzle can be pur- chased by contacting our Customer Care representa- tives by calling 08445 614614. Call to this number will be charged at 5p per minute all times from a BT Landline. This convenient air-driven Turbo Nozzle is perfect for use on upholstery, stairs and area rugs.
  • Page 15 • Remove any clogs from the opening or debris around the brushroll or belt. • Refer to page 14. • Call Electrolux on 08445 614614. Call to this number will be charged at 5p per minute at all times from a BT Landline. Have the model and serial numbers ready when you call.
  • Page 16 Hose Crevice Tool Thank you for purchasing an Electrolux cleaner. Don’t Forget to Use Genuine Electrolux Parts Caution: Damages caused by the use of non-genuine parts are not covered by the Electrolux Guarantee. Part No. 75598D Printed in PRC (09/06)

Table of Contents