Electrolux 316488521 Installation, Use & Care Manual page 11

Outside r Outside rear exhaust Outside r Outside r Outside r ear exhaust ear exhaust ear exhaust ear exhaust
(Horizontal duct– 3 1/4"x 10" Rectangular)
• • • • • Use the diagram or the hood as a template
and mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Wood shims (recessed
bottom cabinets only)
Cabinet front
Horizontal duct
3 3/4"
access hole
Cabinet
5 1/4"
bottom
13 15/16" (30" Hood)
16 15/16" (36" Hood)
Center line
Hood mounting screws (4)
Recir Recir culating culating
Recir Recirculating Recir culating culating
Use the hood as a template and mark the locations
on the cabinet for the electrical wiring and keyhole
screw slots.
Since the hood is to be recirculated (not to be vented
outside), do not cut out any vent openings in the wall
or cabinet bottom.
Step 9 Step 9
Step 9 Step 9 Step 9
Choose Venting Option Choose V Choose V enting Option enting Option enting Option
Choose V Choose V enting Option
The hood can be set to vent outside or to recirculate
air back into the kitchen.
Set for
outside venting
recirculating
Stop tab
Hood shown Lying upside down
The plastic vent lever is located near the center of the
hood opening.
T T T T T o vent to the outside, o vent to the outside, make sure the plastic vent o vent to the outside, o vent to the outside, o vent to the outside,
HORIZONT HORIZONT AL AL
lever is in the HORIZONT HORIZONTAL HORIZONT AL position (flat against the AL
metal top of the hood).
T T T T T o r o r o recir o r o r ecir ecirculate air into the kitchen, ecir ecir culate air into the kitchen, culate air into the kitchen, culate air into the kitchen, culate air into the kitchen, make sure the
VER VER
plastic vent lever is in the VER VERTICAL VER
against the plastic blower housing).
NOTE: NOTE: NOTE: NOTE: In order to change the vent lever position, you NOTE:
will need to pull the lever out slightly to clear the
plastic tabs.
Step 10 Step 10 Step 10
Step 10 Step 10
For recessed bottom cabinet only For r For r For r For r
If the cabinets have front, side or back trim, make 2
wood shims the width of the trim and attach them to
the cabinet bottom recess on both sides. See
1/8" 7/16"
previous page for marking locations.
5 1/4"
12 7/16"
13 15/16" (30" Hood)
16 15/16" (36" Hood)
Electrical access hole
(in wall)
Step 11 Step 11 Step 11
Step 11 Step 11
Cut holes at marked locations for duct and electrical
wiring. For the vertical duct, cut out 3/4" extra toward
the front of the cabinet so you can move the duct
freely when installing the hood.
It may also ease installation by cutting the hole 10 1/
2" instead of 10".
Step 12 Step 12 Step 12
Step 12 Step 12
Drive a mounting screw (from the hardware packet)
partway into each center of the narrow neck of the
Set for
keyhole slots marked on the cabinet bottom.
Step 13 Step 13
Step 13 Step 13 Step 13
Fix the wiring conduit to the hood.
Stop tab
Step 14 Step 14
Step 14 Step 14 Step 14
Slide the hood back against the wall. Tighten the
mounting screws. Be sure the screw heads are in the
narrow neck of the keyhole slot.
Connect Ductwork to hood.
TICAL TICAL
TICAL position (flat TICAL
Installing the hood
ecessed bottom cabinet only ecessed bottom cabinet only ecessed bottom cabinet only ecessed bottom cabinet only
W W W W W ood shims ood shims ood shims ood shims ood shims
11 11
11
11 11