Advertisement
Reception
I
n s t a l l a t i o n
• Shares frequency with
o f A c c e s s o r i e s
several different types of
Installing Spring-Type Belt Clip
devices — interference may
be experienced
• Position clip, spring pointing up,
• Radio interference may cause
to backside of handset
interruption to conversation
• Align four prongs on clip to four
slots on handset
• Moving handset while talking
or relocating base unit may
• Gently press clip to snap prongs
improve reception
into place
Note:
Installing Headset
If reception is lost completely dur-
• Pull back rubber cover from
ing conversation mode,
side of headset to expose
replace handset on base unit to
connection port
resynchronize range; call is lost.
• Insert 2.5mm connector of
headset jack
Out of Range
• Replace rubber cover after use
• Communication is halted for 30
to ensure port cleanliness
seconds during conversation
Notes:
• Handset will automatically search
for and select a clear channel
1.When headset is plugged in,
• If none is found, an error tone
handset speech path becomes
will ring on handset when not on
disabled.
base station
2. Rubber cover need not be
Manual Channel Selection
completely removed to use port.
If reception becomes garbled or
static occurs, channels can also be
manually changed.
O
p e r a t i o n
• Press ["CH"] key during conver-
sation to activate 3-channel
All operational instructions assume
semi-auto scan (MCA)
that these features are assigned to
• While channel is changing, low
the DTP-16HC-1 Terminal: Prime
battery LED will blink
Line Pickup to your Primary
Extension and Ringing Line.
• If channel not found, error
tone will sound and channel
Receiving Calls
will not change
When receiving a call, handset rings
and Message Waiting LED blinks
rapidly in conjunction with base
station LED.When handset is on
base station, only the base station
rings and Message Waiting LED
blinks rapidly.When handset is in
standby mode, both handset and
base station ring and Message
flashes then remains lit as
Waiting LED blinks rapidly in
communication path is
conjunction with base station LED.
established between handset
and base station.
Note:
2.The Auto Standby feature
When [Ringer "ON/OFF"] switch is
(no need to press ["TALK"] key
in "Off" mode, handset will not
to disconnect call) only applies
ring, but Message Waiting LED
when returning handset to
flashes.
base station.
Auto Talk Feature Switching
3.While in talk mode, Message
To change mode, press and hold
Waiting LED is inactive; when
["TRF"] key while moving [Ringer
call is disconnected, Message
"ON/OFF"] Switch from "Off" to
Waiting LED is reactivated and
"On. " When mode is changed, confir-
flashes if messages are waiting.
mation tone sounds: Auto Talk Off
Making Calls with Auto Talk Off
produces 3 beeps; Auto Talk On
produces 2 beeps.
• Lift handset from base unit
Note:
• Press any key
This feature only applies if tele-
• Listen for dial tone and dial
number
phone type allows for Prime Line
selection when going off-hook on
• Begin conversation
that station.
• At end of conversation, return
Answering Calls with
handset to base station or press
Auto Talk Off
["TALK"] key
• Call is disconnected
• Lift handset from base unit
• Press any key
Making Calls with Auto Talk On
• Begin conversation
• Lift handset from base unit
• At end of conversation, return
• Listen for dial tone and dial
handset to base station or press
number
["TALK"] key
• Begin conversation
• Call is disconnected
• At end of conversation, return
Answering Calls with
handset to base station or press
Auto Talk On
["TALK"] key
• Call is disconnected
• Lift handset from base unit
• Begin conversation
Notes:
• At end of conversation, return
1. ["TALK/BATTERY LOW"] LED
handset to base station or press
flashes then remains lit as
["TALK"] key
communication path is estab-
lished between handset and base
• Call is disconnected
station, and dial tone is heard.
Notes:
The communication time out is
5 seconds. If communications
1. ["TALK/BATTERY LOW"] LED
path cannot be established
Placing Calls on Hold with a
within 5 seconds, error tone
call in progress from the
will sound and handset reverts
base station:
to standby mode.
• Press ["HOLD"] key or ["TALK"]
key
2.Applies ONLY when connected
to an NEC Electra Elite
®
2 — In
• Return handset to base station
conversation mode, handset will
• Press flashing ["LINE"] key to
no longer produce DTMF, but the
continue call
base station will produce DTMF.
• Press ["TALK"] or pick up
handset
With a call in progress from the
F
e a t u r e s
a n d
handset (PBX):
S e t t i n g s
• Press ["TRF"]
Setting Handset Ringer On/Off
• Listen for stutter tone
When handset is in standby mode,
• Press ["TRF"] to continue call
ringer volume can be adjusted Low
With a call in progress from the
or High by pressing ["VOL"] key.
handset (Key System):
Ringer volume can be adjusted even
• Press ["TRF"] key or ["TALK"] key
when [Ringer "ON/OFF"] switch is
in "Off" position.
• Return handset to base station
Adjusting Handset/Headset
• Press flashing ["LINE"] key to
Reception Volume
continue call
When call is in progress, press
• Press ["TALK"] or pick up
["VOL"] key repeatedly to increase
handset
handset/headset speaker volume
Note: After a preprogrammed time,
from NORMAL to MEDIUM to
any held call will recall to the orig-
HIGH to LOW — in this order.
inating terminal.
After disconnect, volume reverts
to NORMAL setting.
Conference Calling with a call
in progress:
Muting Handset/Headset
Volume
• For Electra Elite/Electra
Professional — Press ["CONF"]
When call is in progress, press
key on base station
["MUTE"] key to disable micro-
phone.The ["TALK/BATTERY LOW"]
• For NEAX
LED flashes when handset/headset
["TRF"]
is muted.Voice is not transmitted in
• Place second call (internal or
MUTE mode. Press ["MUTE"] key
external)
again to reactivate microphone.
• Announce conference (optional)
Note:
• Press ["CONF"] from base station
Handset/headset volume control
to establish conference
is compatible with new HAC
regulations.
®
2400/2000 — Press
Advertisement
