Confirm Version; Save Unit Data To Memory Card; Software Upgrade - Panasonic AKHRP200 Operating Instructions Manual

Setup.Mode.Operations.
2..
Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• After confirmation, unit settings are initialized and it is automatically
restarted.
ND
M.GAIN
• To cancel initializing, select [n] and press <EXECUTE>.
17.Confirm.version
Press.<SELECT>to.select.menu.number.[17].
• The version information is displayed.
• Press <SAVE/LOAD> to show the 8-digit version number split up in 3,
2 and 3 digits.
UP
ND CC SHT SYNC
M.GAIN M.PED
DATA
SET
IRIS
DOWN DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
UP+DOWN SAVE/LOAD EXIT EXECUTE
Press to switch display Press to select the menu number
digits
Press to exit setup mode (hold down)
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
18.Save.unit.data.to.memory.card
This functions are used by the manufacturer during maintenance.
1..
Press.<SELECT>to.select.menu.number.[18].
Select y (Save)/n (Cancel)
UP
ND CC
M.GAIN
DATA
SET
IRIS
DOWN DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
UP+DOWN SAVE/LOAD EXIT
Press to exit setup mode
(hold down)
2..
Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
ND
M.GAIN
• The file is saved to the memory card and [Fin] appears when saving
ends.
12
(continued)
CC SHT SYNC
M.PED
IRIS
Display digit indication (first 3 digits)
Display digit indication (middle 2 digit)
Display digit indication (last 3 digits)
CAMERA
10-19
No.
SELECT
SHT SYNC CAMERA
M.PED 10-19
No.
SELECT
EXECUTE
Press to confirm
Press to select the
menu number
CC SHT SYNC
M.PED
IRIS
• [E02] is displayed if the save operation to the memory card fails.
(→page 13)
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when a unit data file with the same name as the
one you are attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>. (→page 13)
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
19.Software.upgrade
For details on software upgrades, refer to "Software upgrades"(→page
3).
1..
Press.<SELECT>to.select.menu.number.[19].
Select y (Upgrade)
UP
ND CC
M.GAIN
DATA
SET
IRIS
DOWN DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
UP+DOWN SAVE/LOAD EXIT
Press to exit setup mode
(hold down)
2..
Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Upgrading starts.
ND
M.GAIN
• When the upgrade ends, [Fin] appears.
<Note>
If the upgrade fails for some reason, <SHIFT> may start to flash after
the restart. If this happens, perform the upgrade process again.
SHT SYNC CAMERA
M.PED 10-19
No.
SELECT
EXECUTE
Press to confirm
Press to select the
menu number
CC SHT SYNC
M.PED
IRIS