PLC-WM4500/WM4500L Expand Serial Command Functional Specifications Overview 0û This Functional Specification defines communication for PLC-WM4500 / WM4500L. 0û Supporting Firmware Ver. 1.x of the projector. 0û Most commands are used to control a projector remotely from a computer with RS-232C. Therefore commands in this document are defined as Expand Serial Commands.
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications Notes for communication Expand Serial Command is defined as a single command per line that starts with “C” and ends with carriage return (0x0D). There are two types of commands; Functional Execution Commands and Status Read Command.
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications Functional Execution Command Table 5.1 Image Command Table Item Execute command CF_BRIGHT_%1 [CR] Set value of Brightness CF_CONT_%1 [CR] Set value of Contrast CF_COLOR_%1 [CR] Set value of Color CF_TINT_%1 [CR] Set value of Tint CF_SHARP_%1 [CR] Set value of Sharpness CF_GAMMA_%1 [CR]...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications CF_CCAPTIONCOLOR_%1 Set color of Closed caption [CR] CF_DELAYCTRL_%1[CR] Set Video delay control function CF_TESTPAT_%1[CR] Set Test pattern display function CF_FDEFAULT_%1 [CR] Reset to Factory Default settings Other Command Table Execute command Item CF_KEYEMU_%1 [CR] The same operation as Control Key CF_MENU_%1 [CR] Set ON/OFF of Menu...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications Status Read Command Table Image Status Read Command Table Status Read command Item CR_BRIGHT [CR] Get value of Brightness CR_CONT [CR] Get value of Contrast CR_COLOR [CR] Get value of Color CR_TINT [CR] Get value of Tint CR_SHARP [CR] Get value of Sharpness CR_GAMMA [CR]...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications Screen Status Read Command Table Status Read command Item CR_SCREEN [CR] Get selected screen size CR_VSCALE[CR] Get setting status of V Scale CR_VPOS[CR] Get setting status of V Position CR_HSCALE[CR] Get setting status of H Scale CR_HPOS[CR] Get setting status of H Position CR_KYSTNMODE[CR]...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications Get selected location of infrared remote receiver of remote CR_RSENS [CR] control CR_RTYPE [CR] Get supported Remote Control type (IR/RF) CR_P-MANE [CR] Get Power management setting status CR_P-MANETIME [CR] Get setting time for Power Management CR_STANDBYMODE [CR] Get selected mode of Standby function CR_ON-STA [CR]...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications Error Code Table Error Code Contents -When the received data cannot be decoded -Parameter designation error (wrong digit number, including invalid value, etc.) Normal reception (This is “Not” error) The function is not available in the selected Mode Selected value is out of range (Not reflected) Command mismatched to Hardware (the command is for Optional function which is not implemented)
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications Functional Execution Command 8.1 Format 1) PC issues commands in format as below: Pattern1: “CF_ COMMAND” [CR] Pattern2: “CF_ COMMAND _” %1 [CR] CF_: Header COMMAND: String %1: Parameter (String) _: Space (To separate COMMAND and Parameter) 2) The projector decodes the received command and when it is ready to receive the next command, it returns the response.
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications Image Command 8.4.1 CF_ BRIGHT Command Command “CF_BRIGHT_%1” [CR] “000-063”--------------- Directly specify setting value of Brightness “UP”--------------------- Increment setting value of Brightness by 1 “DN”--------------------- Decrement setting value of Brightness by 1 Set user controlled value of Brightness (Available only in the normal Power ON status) Details The value set by this command will not be stored in the projector’s memory.
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.4.5 CF_SHARP Command Command “CF_SHARP_%1” [CR] “000-031”--------------- Directly specify setting value of Sharpness “UP”--------------------- Increment setting value of Sharpness by 1 “DN”--------------------- Decrement setting value of Sharpness by 1 Set user controlled value of Sharpness (Available only in the normal Power ON status) Details The value set by this command will not be stored in the projector’s memory.
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.4.8 CF_COLTEMP Command Command “CF_COLTEMP_%1” [CR] “000” ------------------------------ Xlow “001”------------------------------- Low “002”------------------------------- Mid “003”------------------------------- High Set Color Temperature The value set by this command will not be stored in the projector’s memory. Details Therefore, when the power is turned to ALL OFF status, the value returns to the original setting.
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.4.11 CF_PROGV Command Command “CF_PROGV_%1” [CR] “ON” ----------------- Set Progressive scan to On. “FILM” --------------- Set Progressive scan to Film. “OFF” ---------------- Set Progressive scan to OFF. “UP” ------------------ Switch setting forward direction (OFF→ON→FILM→OFF) “DN”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.4.13 CF_IMAGEADJ Command Command “CF_IMAGEADJ_%1”[CR] “RST”------ Reset adjusted value for the Image “STR1”---- Store current adjusted value to Image 1 “STR2”---- Store current adjusted value to Image 2 “STR3”---- Store current adjusted value to Image 3 “STR4”---- Store current adjusted value to Image 4 “STR5”---- Store current adjusted value to Image 5 “STR6”---- Store current adjusted value to Image 6...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications PC Adjust Control Command 8.5.1 CF_FSYNC Command Command “CF_FSYNC_%1” [CR] “0000-0031” ----------------- Directly specify setting value of Fine Sync “UP” --------------------------- Increment setting value of Fine Sync by 1 “DN” --------------------------- Decrement setting value of Fine Sync by 1 Set value of Fine Sync in PC signal (Available only in the normal Power ON status) Details...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.5.4 CF_H-POS Command Command “CF_H-POS_%1” [CR] “0000-nnnn” -------- Directly specify setting value of Horizontal Position “nnnn” indicates maximum value, which is current value of (Total dots - Display area H) “UP” ------------------- Increment setting value of Horizontal Position by 1 “DN”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.5.7 CF_DLINE Command Command “CF_DLINE_%1” [CR] “0100-nnnn” ----------- Directly specify setting value of Display Line “nnnn” indicates maximum value, which is current value of (Total Line - Position V). “UP” ------------------- Increment setting value of Display Line by 1 “DN”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.6.4 CF_INPUT 2 Command Command “CF_INPUT2_%1” [CR] “VIDEO” ---------------------------- Select Composite Video Input “YPBPR” --------------------------- Select Y/Pb/Pr Input “ANALOG” ------------------------- Select RGB Input Select Input 2 as well as Source specified in %1. (Available only in the normal Details Power ON status) Acceptable...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.7.7 CF_KEYSTONE Command Command “CF_KEYSTONE _%1” [CR] “UP” ------------- Correct Keystone distortion to reduce upper part of image “FUP” ----------- Correct Keystone distortion to reduce upper part by 2 steps “DN” ------------- Correct Keystone distortion to reduce lower part of image “FDN”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.7.11 CF_SCREENASPECT Command Command “CF_SCREENASPECT_%1”[CR] “43MODE” ÿ e ÿ e ÿ e ÿ e ÿ e ÿ e ÿ e Select 4:3 mode “169MODE” ÿ e ÿ e ÿ e ÿ e ÿ e ÿ e Select 16:9 mode “1610MODE”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications Lamp Command 8.8.1 CF_LAMPMODE Command Command “CF_LAMPMODE_%1” [CR] “NORMAL” ------------------------ Set Lamp status to Normal mode “ECO1” ----------------------------- Set Lamp status to Eco1 mode “ECO2” ----------------------------- Set Lamp status to Eco2 mode “AUTO” ----------------------------- Set Lamp status to Auto mode Select Lamp mode (Available only in the normal Power ON status) Details The value set by this command is stored in EEPROM and the setting remains...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications Sound Command 8.9.1 CF_VOLUME Command Command “CF_VOLUME_%1” [CR] “000-063” --------------------------- Directly specify value of Volume. “UP” --------------------------------- Increment setting value of Volume by 1 “DN” --------------------------------- Decrement setting value of Volume by 1 Control level of Volume (Available only in the normal Power ON status) Set Volume Up/Down the same way as RC and also directly specify value of Details Volume.
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.10.4 CF_DISP Command Command “CF_DISP_%1” [CR] “ON” ----------------------------- Set Display to On “CNTDWNOFF” --------------- Set Display to Count down Off “OFF” --------------------------- Set Display to Off “UP” --------------- Switch forward (On → Count down Off → Off → On → ---) “DN”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.10.12 CF_PIPPOSITION Command Command “CF_PIPPOSITION_%1” [CR] “POS1” -------------------- Move main picture position to up “POS2” -------------------- Move main picture position to down “POS3” -------------------- Move main picture position to left “POS4” -------------------- Move main picture position to right “POS5”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.10.15 CF_PIPMODEFREE Command Command “CF_PIPMODEFREE_%1” [CR] “USER1” --------------------------- Set User1 to Free status “USER 2” -------------------------- Set User2 to Free status “USER 3” -------------------------- Set User3 to Free status “USER 4” -------------------------- Set User4 to Free status “USER 5”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.10.26 CF_P-MANETIME Command Command “CF_P-MANETIME_%1” [CR] “01” - ”30” ----------------------- Directly specify setting time by the minute “UP” ------------------------------- Increment value by 1 (Switched in 01→02→ --- → 30 → 01 order) “DN” ------------------------------ Decrement value by 1 (Switched in 30→29→...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.10.30 CF_PTIMEMODE Command Command “CF_PTIMEMODE_%1” [CR] “COUNTUP” ---------------------- Set P-timer to Count up mode “COUNTDN” ---------------------- Set P-timer to Count down mode Select count up/down mode of P-timer. (Available only in the normal Power ON status) Details The status set by this command is stored in EEPROM and setting value remains effective even after the power is turned to ALL OFF status.
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.10.34 CF_PJPINCODE Command Command “CF_PJPINCODE_%1” [CR] “0000 – 9999” ------------- Directly specify PJ PIN code Enter PIN code to cancel PIN code lock (Available only in the normal Power ON status) PIN code can not be changed. (Only PIN code lock is canceled.) *When PIN code Lock is enabled: PIN code is matched ------------------------- Command is valid (Acceptable) PIN code is mismatched -------------------- Command is invalid (Error code “102”)
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.10.37 CF_DELAYCTRL Command Command “CF_DELAYCTRL_%1” [CR] “OFF”---------- Set Video delay control to OFF “ON”------------ Set Video delay control to ON Select the mode of Video delay control (Valid only when in the normal Power ON status) Details The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 8.11.3 CF_POWER Command Command “CF_POWER_%1” [CR] “ON” ----------------------------- Power ON “OFF” --------------------------- Power OFF * Issuing another command during countdown process forced countdown operation to be terminated. * Error Code is returned in some projector statuses, which indicates the command is impossible to be executed.
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications Status Read Command 9.1 Format PC issues commands in format as below: “CR_ COMMAND” [CR] Command: String When projector receives the appropriate command, it returns the required data as a string. “000_” %1 [CR] %1: Required Data (String) When the received data cannot be decoded, the projector returns “?”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.4 Image Status Read Command 9.4.1 CR_BRIGHT Command Command “CR_BRIGHT” [CR] Details Get user controlled value of Brightness Acceptable “000_%1” [CR] Response “000 – 063” Unacceptable “Error Code” [CR] 9.4.2 CR_CONT Command Command “CR_CONT” [CR] Details Get user controlled value of Contrast Acceptable...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.4.6 CR_GAMMA Command Command “CR_GAMMA” [CR] Details Get user controlled value of Gamma Acceptable “000_%1” [CR] Response “000 – 015” Unacceptable “Error Code” [CR] 9.4.7 CR_WBAL-R Command Command “CR_WBAL-R” [CR] Details Get user controlled Red value of White Balance Acceptable “000_%1”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.4.11 CR_OFFSET-R Command Command “CR_OFFSET-R” [CR] Details Get user controlled Red value of Offset Acceptable “000_%1” [CR] Response “000 – 063” Unacceptable “Error Code” [CR] 9.4.12 CR_OFFSET-G Command Command “CR_OFFSET-G” [CR] Details Get user controlled Green value of Offset Acceptable “000_%1”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.5 PC Adjust Status Read Command 9.5.1 CR_FSYNC Command Command “CR_FSYNC” [CR] Details Get value of Fine Sync Acceptable “000_%1” [CR] “0000 – 0031” Response “Error Code” [CR] --- When command is not available in the given Unacceptable condition (such as being selected input) “?”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.5.6 CR_DDOTS Command Command “CR_DDOTS” [CR] Details Get value of Display Dots Acceptable “000_%1” [CR] “0100 – nnnn” (nnnn = Total Dots – Position H) Response “Error Code” [CR] ---- When command is not available in the Unacceptable given condition (such as being selected input “?”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.6 Video Status Read Command 9.6.1 CR_SERSYS Command Command “CR_SERSYS” [CR] Get selected current signal. Auto detected signal is returned in Auto mode Details Only available when Input is Y,Pb/Cb,Pr/Cr, S-Video or Video. (This is not the case for PC-Analog and HDMI signals) Acceptable “000_%1”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.7.7 CR_SYSLIST Command Command “CR_SYSLIST” [CR] Details Get possible systems for System list Acceptable “000_%1_%2_---_%x” [CR] Error Code “101” is returned for no signal. Otherwise following values are returned according to Source. When input is PC-Analog; “XGA1”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.8.6 CR_ KYSTNMODE Command Command “CR_KYSTNMODE” [CR] Details Get setting status of Keystone Store Mode Acceptable “000_%1” [CR] “STR” ---------------------- Store mode is “Store” Response “RST” ---------------------- Store mode is “Reset” Unacceptable “?” [CR] -------------------- When unknown command is received 9.8.7 CR_CEIL Command Command...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.9 Lamp Status Read Command 9.9.1 CR_LAMPREPL Command Command “CR_LAMPREPL” [CR] Details Get information of Lamp Replacement time Acceptable “000_%1” [CR] “1Y” ----------------- indicates over lamp replacement time Response “1N” ----------------- indicates under lamp replacement time Unacceptable “?”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.9.6 CR_PROJH Command Command “CR_PROJH” [CR] Details Get total running time of Projector (in hours) Acceptable “000_%1” [CR] Response “0000000 – 0099999” Unacceptable “Error Code” [CR] 9.9.7 CR_HMLAMP Command Command “CR_HMLAMP” [CR] Details Get total lamp number Acceptable “000_%1”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.10 Sound Status Read Command 9.10.1 CR_VOLUME Command Command “CR_VOLUME” [CR] Details Get volume value by user control Acceptable “000_%1” [CR] Response “000 – 063” Unacceptable “Error Code” [CR] 9.10.2 CR_MUTE Command Command “CR_MUTE” [CR] Details Get setting status of Sound Mute.
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.11 Setting Status Read Command 9.11.1 CR_LANG Command Command “CR_LANG” [CR] Details Get selected language Acceptable “000_%1” [CR] “ENG” -------------------------- English is selected “DEU” -------------------------- German is selected “FRA” -------------------------- French is selected “ITA” --------------------------- Italian is selected “ESP”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.11.5 CR_LOGO Command Command “CR_LOGO” [CR] Details Get setting status of Logo Acceptable “000_%1” [CR] “DFLT” ----------------------------- Default Logo is enabled Response “USER” --------------------------- User is enabled “OFF” ------------------------------ Logo is disabled Unacceptable “Error Code” [CR] 9.11.6 CR_LOGOLOCK Command Command “CR_LOGOLOCK”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.11.9 CR_PIPMAININP Command Command “CR_PIPMAININP” [CR] Details Get Input and Source for “Picture in Picture”. (Main picture) Acceptable “000_%1_%2” [CR] “1” -------------------- Input1 is selected “2” -------------------- Input2 is selected “3” -------------------- Input3 is selected “ANALOG --------------------- ANALOG RGB is selected Response “VIDEO”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.11.12 CR_PIPFRAMELOCK Command Command “CR_PIPFRAMELOCK” [CR] Details Get setting status of Frame lock in “Picture in Picture”. Acceptable “000_%1” [CR] “MAIN” -------------------- Main picture is selected Response “SUB” --------------------- Sub picture is selected Unacceptable “Error Code”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.11.35 CR_PJLOCKMENU Command Command “CR_PJLOCKMENU” [CR] Details Get ON/OFF setting status of PIN code lock on menu Acceptable “000_%1” [CR] “ON1” -------------------- PIN code lock ON 1 is set on the menu Response “ON2” -------------------- PIN code lock ON 2 is set on the menu “OFF”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.11.39 CR_TESTPAT Command Command “CR_TESTPAT” [CR] Details Get setting status of Test pattern Acceptable “000_%1” [CR] “COLOR” ---------------------- Color bar is displayed “GRAD1” ---------------------- 16step(white→black) is displayed “GRAD2” ---------------------- 16step(white←black) is displayed “GRAD3” ---------------------- 16step(white↓black) is displayed Response “GRAD4”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.12 Other Status Read Commands 9.12.1 CR_STATUS Command COMMAND “CR_STATUS” [CR] Get operating status of Projector Detail Same as “CR0” in basic command except error code follows it. Acceptable “000_%1” [CR] “00” = Power ON “80”...
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.12.5 CR_TEMPFAIL Command Command “CR_TEMPFAIL” [CR] Get the temperature inside a projector when abnormal temperature status Details occurs. It is possible to get the temperatures all at once when several sensors installed. Acceptable “000_%1_%2_%3” [CR] %1 ------------------ Sensor 1 temp.
PLC-WM4500/WM4500L Expand Serial Command Functional Specifications 9.12.6 CR_TEMP Command Command “CR_TEMP” [CR] Get the current temperature information inside a projector. Details It is possible to get the temperatures all at once when several sensors installed. Acceptable “000_%1_%2_%3” [CR] %1 ------------------ Sensor 1 temp. (External temp.) %2 ------------------ Sensor 2 temp.