Table of Contents
Advertisement
Available languages
Available languages
Quick Links
Operator's Manual
I
4 x 36" Belt, 8" Disc
6 x 48" Belt, 9" Disc
SANDER WITH DUST COLLECTION
Model Nos.
351.215690
351.225930
CAUTION:
Read and follow
all Safety Rules and Operating
Instructions
before First Use
of this Product.
Keep this
manual with tool.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
wwwosears.com/craftsman
21969.02
Draft (06/11/04)
Advertisement
Table of Contents
Related Manuals for Craftsman 351.215690
Summary of Contents for Craftsman 351.215690
- Page 1 SANDER WITH DUST COLLECTION Model Nos. 351.215690 351.225930 CAUTION: Read and follow all Safety Rules and Operating Instructions before First Use of this Product. Keep this manual with tool. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. wwwosears.com/craftsman 21969.02 Draft (06/11/04)
- Page 2 • Work area should be properly lighted. • Proper electrical receptacle should be available for tool. Warranty ......... Three-prong plug should be plugged directly into properly Safety Rules ........grounded, three-prong receptacle. Unpacking ........• Extension cords should have a grounding prong and the three Assembly ........
-
Page 3: Tools Needed
• Make sure there is plenty of room for moving the work- piece. There must be enough room that neither operators nor bystanders will have to stand in line with the wood Refer to Figure 1. while using the tool. Allow room so that belt assembly can be positioned horizontally. -
Page 4: Power Source
ATI'ACH DUST COLLECTION • Loosen knob. Using a combination square, set the table perpendicular to the disc, and secure in position. If Refer to Figure 5, necessary, set pointer at 0°. • Place clamp over bag sleeve. • Slide sleeve with clamp over the dust port. •... -
Page 5: Grounding Instructions
Power supply tothemotor iscontrolled byasingle p ole permanent electrical ground such as a properly grounded locking rocker switch. Remove thekey toprevent unautho- water pipe, a properly grounded outlet box or a properly rized use. grounded wire system. • Many cover plate screws, water pipes and outlet boxes are GROUNDING INSTRUCTIONS not properly grounded. -
Page 6: Specifications
• Make sure all moving parts are free and clear of any DESCRIPTION interference, The Craftsman Belt and Disc Sanders are constructed of • Make sure all fasteners are tight and have not vibrated loose. rugged die cast aluminum and cast iron providing stability and •... -
Page 7: Adjusting Belt Tracking
• Adjustable positive stops are provided for both horizontal and vertical positions. NOTE: The horizontal stops are located on top of the base. Vertical Stop Pivot Bracket Figure 10 - Locking Switch in OFF Position ADJUSTING BELT TRACKING Refer to Figure 11. •... - Page 8 Figure 14 - Attaching the Work Stop Figure 15 - Checking Parallelism of Table Slot to Belt ABRASIVE BELT SANDING • If table needs adjustment, loosen the three bolts beneath table, move table and secure in position. • Finishing flat surfaces: Hold workpiece firmly with both hands;...
-
Page 9: Replacing Abrasive Disc
REPLACING ABRASIVE BELT Refer to Figure 18. • Sanding belt should be replaced when worn, torn, or glazed. Remove table assembly and support rod or work stop. • Remove bracket, deflector and cover. NOTE= Model 215690 - also need to remove mount and two screws (Fig. - Page 10 ;YMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION Motor will not start 1. Low voltage 1. Check power Linefor proper voltage 2. Open circuitin motor or loose 2. Inspect all lead connections on motor for loose or connections open coRRection 3. Defective switch 3.
- Page 11 Service Record Craftsman Sander with Dust Collection I DATE MAINTENANCE PERFORMED REPLACEMENT PARTS REQUIRED...
- Page 12 Model 351.225930 Figure 20 - Replacement Parts Illustration for Belt and Disc...
- Page 13 DESCRIPTION QTY. PART NO. PART NO. DESCRIPTION QTY. Switch 21425.00 16080.00 Idler Assembly Switch Box STD833020 6-1.0 x 20ram Hex Head Bolt* 21443.00 Dust Cover 21428.00 Tension Lever 21437.00 6-1.0 x 10mm Pan Head Screw'* STD863610 20768.00 Abrasive Belt 21441.09 Upper Cover 21426.00 Spring...
- Page 14 Models 351.225930 and 351.215690 Figure 21 - Replacement Parts Illustration for Motor and Dust Collection...
- Page 15 PART NO.FOR PART NO. FOR 225930 215690 DESCRIPTION QTY. Upper Body 21464.00 21894.00 Bottom Plate 21455.00 21455.00 Hose 01043.00 01043.00 6-1.0 x 8mm Set Screw 21452.00 21895.00 Motor Fan 21453.00 21896.00 Motor Assembly (includes Key Nos. 4, 5, 7, 8 and 9) 21472.00 21697.00 Centrifugal Switch...
- Page 16 Model 351.215690 Figure 22 - Replacement Parts I|lustration for Belt and Disc €//1 16 1...
- Page 17 <EY PART NO. DESCRIPTION PART NO. DESCRIPTION QTY. QTY. 21872.00 16080.00 Switch Idler Assy STD833020 6-1.0 x 20ram Hex Head Bolt 21883.00 Switch BOX 21873.00 Tension Lever 21884.00 Dust Cover 20613.00 Abrasive Belt 6-1.0 x 10ram Pan Head Screw STD863610 21875.00 21885.00 Spring...
- Page 18 EL OPERADOR DEBE ESTAR PREPARADO PARA LIJADORA CON RECOLECTOR ELTRABAJO DE POLVO • Use ropa apropiada. No use ropa holgada, guantes, corbatas, anillos, pulseras ni otras joyas que puedan atascarse an tas piezas m6viles de la maquine. Correa de 4 x 36", Disco de 8" •...
- Page 19 EL OPERADOR DEBE SABER COMO USAR E Tope de seguddad LA HERRAMIENTA Varilla de seperte • Use la herramienta correcta pare cada trabaje. Ne fuerce la Conjunte de la mesa herrarnienta o el acoesodo ni los use para una tarea pare la Gancho del cordon de alimentacibn (2) con tornillos (4) que no fueron disedados.
- Page 20 Pemo (B) Flgura 3 - Use de la Mesa con el Disco Pare utilizar la mesa con la correa: • Afloje el perno en la pieza de soporte de pivote. Mueva el conjunto de la correa a la posici6n vertical, y apriete el perno para fi]ada en esa posicibn.
- Page 21 INSTALACION DE LA BOLSA DE RECOLECCION La fuente de alimentaci6n dal motor esteroontrolada por un interruptor oscilante enclavado unipolar. Extraiga la Ilave DE POLVO para evitar el uso no autodzado. Consulte ia Figura 5. • Coloque la abrazadera sobre la manga de la bolsa. INSTRUCCIONES PARA LA CONEXION A TIERRA...
- Page 22 DESCRIPCION • Si el cordbn de extensibn est& desgastado, roto o daSado La Lijadora de correa y disco de Craftsman estd construida de en cualquier forma, reemplacelo inmediatamente. aluminio fundido a presi6n y hierro forjado robusto para propor- cionar estabilidad y un funcionamiento libre de vibraciones.
- Page 23 apagar la lijadora, cambie la posici6n del interruptor a la posiciSn Di_lmetro del disco ........9" inferior. Velocidad del disco ......3500 RPM Se puede bloquear el interruptor para impedir el uso no autoriza- Dimensiones de la mesa ......7 x 10" do de la lijadora.
- Page 24 • Si la correa se mueve haeia Laizquierda, gire la tuerca de alinsaci6n haeia la derecha. Si la corree se mueve hacia la derecha, gire la tuerca de alineaciSn hacia la izquierda. • Vuelva a encender y apagar r_ipidamente Launidad. Si la correa se mueve hacia un lado, continue ajustando La tuerca de alineaci6n seg_n convenga pare centrar la correa en los tambores.
- Page 25 Use el tope de seguridad pare situar y suietar la pieza qua se est_ lijando. Mantanga el extremo topado contra el tope de seguridad y mueva la pieza uniformemente a traves de la correa abrasiva. Tenga mucho cuidado cuando acabe piezas muy delgadas.
- Page 26 • Hay correas abrasivas adicionales disponibles (v6ase Acoescrios Recomendados en la p6gina 15). • Empuje la palanca de tensi6n hacia el tambor impulsor para ADVERTENCIA: AsegL'Jresede que la unidad est6 desconecta- tensar la correa. da de la fuente de alimentaci6n el_,ctrica antes de tratar de dar •...
- Page 27 SINTOMA CAUSA(S) POSIBLE(S) MEDIDA CORRECTIVA ELmotor no arranca 1. Voltaje bajo 1, Verifiqueel voltajecorTecto de la I_neade aiimentaci6n 2. Circuito abierto en el motor o 2. Inspeccione todas las conexiones de conductores conexiones sueltas en el motor para ver que no haya conexiones sueitas o abiertas 3.
- Page 28 Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters.