Table of Contents
Advertisement
.-i,
4_
Z
O
ol
Fo
VCR PLUS÷
Your TVNCR Combo comes
equipped with VCR Plus+ technolo-
gy. This function allows you to
program your VCR simply by
entering the VCR Pfus+ code number
associated with the program you
wish to record.
Note: Before VCB Rus+ can be
used, VCR Plus guide channels must
be programmed, See VCR Rus
Guide Setup in "initial Setup" page
14, if you have not yet programmed
these channels).
'rIMER RECORDING WITH VCR
PLUS+
Pressthe VCRPLUS + button
on the remotecont_
YCR _US* codes_n
appears
Enter the VCR PLUS* code (three-to-
eight digit number) of the show you
wish to record using the 10-key pad
on the remote control. The following
screen witl appear:
Note: If you enter the VCR Plus+
code incorrectly, press CANCEL Of 1 the
remote. The first screen will
reappear.
VCR
PLUS*
Press the OAILY/_/EEKLY
bLr[ton to select how often a
program should be recorded,
ONCE, DAILY, or WEEKLY
(_)
Press the SP/EP button to
select SP or EP recording
speed. (See pg 20 fo_ more
on tape recording speeds)
(_
Press the VCR PLUS'button
Thefollowingscreenwillappear,
displayinga summary oftheinforma-
tion youjustentered:
If the settingsare correct, press the
VCR PLUS' button again to accept. The
following message will appear:
If you wish to make a correction, use
the (&T) buttons to move to the item
and the (q_,)
buttons to correct.Once
corrected press VCR PLUS* t o accept
the settings.
(_
Press the Timer button
on the remote control.The timer
is now in standby mode.
The REC lamp will glow green _ the
front panel of the unit, indicatlog the
timer has been programmed, When the
programmed start time atrk,es, the
REClamp wiil glow _ed and recording
will begin. When the progran'tnedslop
time arrives, the lamp will go out and
the recording _11 automatically stop. If
there are other pro-set recordings the
REC lamp will glow green.
_
TROUBLESHOOTING
/
TIMER
RECORDING
"rROIJBLESHOOTINO
The following are some common
problems/issues
that may arise while
using Timer Recording.
REC limp Marts flashing when yOU
press TIeR
oft the remote control.
No cassette is loaded into VCR.
Insert a cassette into VCR and
contit_ue+
Cassette toaded has its recording tab
removed.
Inserta recordable cassette,or cover
the missing tab hole with two layers of
tape,
ITR
INS'rANT
TIMER
RECORDINO
(n'R/
Instant Timer Recording allows you to set
the VCR timer after the videotaping of a
program has begun. _
ITR timer can
be programmed to stop recording up to
four hours after ithas begun.
To use the ITR timer, the VCR must
already be recording. Press the REC/ITR
button on the front panel of the VCR
(Note: This function cannot be accessed
with the remote control)
REC/Im
The following display wilt appear on the
screen:
The following memMigeappears
when attemptingto eject tape or
operate VCR:
Pressthe TIMER button and set Timer
Mode to Off, Try operating VCR again.
To stop taping once automatic
recording his begun.
Press theTIMER button, then theSTOP
button.
Ti_etimer above is set to stop mc_'ding in
30minutes,
Press the ITR button again to increase
the amount of time on the ITR timer. Each
press increases the amount by 30
minutes. The ITR timer can he set from a
minimum of thirty minutes 'ITR 0:30' to a
maximum of four hours 'ITR 4:00' When
the time allotted to the ITR expires, the
recording automatically shuts off.
Note: To cancel the ITR timer, press the
REC/ITRbutton until the on-screen display
disappears.
Note: TO stop recording before the
allotted time expires, press the STOP
button.
o
o
Advertisement
Table of Contents
