Sharp AN-L10T Operation Manual

OPERATION MANUAL
MODE D'EMPLOI
BEDIENUNGSANLEITUNG
MANUAL DE OPERACION
For Customers in the U.S.A.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
WARNING:
FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by
the manufacturer could void the user's authority to operate
this equipment.
INFORMATION
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
operation manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his own
expense.
For Customers in Canada
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH
CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST
CONFORME À LA NORME NMB-003 DU CANADA.
This equipment complies with the requirements of Directives
89/336/EEC and 73/23/EEC as amended by 93/68/EEC.
Ce matériel répond aux exigences contenues dans les
directives 89/336/CEE et 73/23/CEE modifiées par la directive
93/68/CEE.
Dieses Gerät entspricht den Anforderungen der EG-
Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/
EWG.
Este aparato satisface las exigencias de las Directivas 89/
336/CEE y 73/23/CEE, modificadas por medio de la 93/68/
CEE.
Printed in Japan
Imprimé au Japon
In Japan gedruckt
Impreso en Japón
AN-L10T
TINS-7267CEZZ
1P01-JKG
10BASE-T
10BASE-T BOARD
CARTE 10BASE-T
10BASE-T-BOARD
TARJETA 10BASE-T
10BASE-T
Included Items
1 10BASE-T BOARD
1 Plotter
7 Screws
Part Names
10BASE-T CONTROL
10BASE-T
LINK TX/RX
3
1
2
1
2
3
•
•
ENGLISH
Warning:
10BASE-T Board installation/uninstallation must be performed
by authorized service personnel only.
Warning
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user
may be required to take adequate measures.
The AN-L10T 10BASE-T board can be installed in an expan-
sion slot on a Sharp projector to control the projector by
10BASE-T interface.
Before installing and using this board, be sure to thoroughly
read the operation manuals accompanying the projector and
Sharp Advanced Presentation Software Professional Edition.
Part Names
1 10BASE-T port
Use UTP cables for 10BASE-T/100BASE-TX (category5).
When connecting a PC to this board, use a cross type
cable; and when connecting a Hub to this board, use a
straight type cable.
2 LED indicator ( LINK )
Lights up when this board is linked.
3 Status LED ( TX/RX )
Lights up when data is transmitted or received.
Set up
A. "Setting Up" the Projector
1. Select "Options" from the menu screen of the projector which
the 10BASE-T board is installed.
2. Select "LAN board".
Sub menu screen for set up appears.
3. Select "IP Address Set" and enter the address assigned for
this board.
4. Enter the Gateway address and Subnet mask.
• If the IP address, Gateway address or Subnet mask is
unknown, refer to a network administrator.
B. Setting Up the Sharp Advanced Presentation Software
Professional Edition
Enter the IP address as in step A-3.
When setting the "Operation Mode" to the "Single Projector
Operation Mode", enter the address in the "Projector Setting"
menu, and to the "Multiple Projector Operation Mode", enter it
in the "Scan Setting" menu.
Troubleshooting
If it does not operate correctly, check cable connection and
each setting related to IP address, Gateway address, Subnet
mask, etc.
Use the Sharp Advanced Presentation Software Professional
Edition Version 1.3 or higher.
Download the latest version from our website using the FRANÇAIS
following URL:
http://www.sharp-world.com/projector/
Major Specifications (Interface)
Standard: Conforms to IEEE802.3
• Connector: RJ-45
• Max. transmission speed: 10 Mbps*
• Max. transmission range: 330 ft. (Approx. 100m)*
*Between the hub and this board
• Note that the specifications and the appearance of this
board are subject to change without prior notice for the
purpose of design improvements.