Sharp 14T1-U Operation Manual

E1 SAFETY PRECAUTIONS
Damage
Turn off the power and unplug
the power cord from the wall
outlet immediately if the TV set
begins to make any unusual noises or gives
off smoke or an unusual smell. Then call your
dealer for service.
Unstable surface
and shocks
Do not place this TV set on an
unstable cart, stand, shelf, or
table. The TV set may fall, causing serious injury
to a child or adult, and serious damage to the
set. Sharp recommends securing the TV set to
a stable surface or wall to prevent the set from
falling due to sudden shocks or impact.
Moisture
To prevent electrical shock,
do not use the TV set in an
excessively damp place.
Liquid entry
Do not place a fl ower vase
or anything else containing liquid
on the TV set, as liquid spilt on the
TV set can cause electrical shock
or failure.
TV Set position
Do place the TV set onto an even
stand, table or rack which size is
bigger than the TV set.
If the TV set is put onto a smaller
size or uneven stand, table or rack may cause
the TV cabinet distort.
Do not put or insert anything between TV set and
the stand, table or rack.
Ventilation
Do not place this TV set in a
confi ned area, such as on a
bookshelf or in a built-in case.
Leave adequate space behind the TV for proper
ventilation.
(На звороті)
ENGLISH
УКРАЇНСЬКА
14T1-U_EN.indd 1 14T1-U_EN.indd 1
COLOUR TELEVISION
14T1-U
OPERATION MANUAL
Servicing
To reduce the risk of electric
shock, do not remove the back of
the cabinet. This TV set contains
dangerous voltage.
Power-cord protection
To prevent electrical shock, do
not subject the AC power cord to
damage by bending or twisting it,
or by placing heavy items on top
of it and do not place the AC power cord under the
TV set. If the AC power cord becomes damaged,
unplug it from the wall outlet immediately and call
your dealer for service.
Water
To prevent fi re or electrical
shock, do not place the TV set
near a bathroom, swimming
pool or other area where it may
become wet.
Object entry
Never insert or drop any metallic
or infl ammable objects into
the ventilation openings of the
TV set, as this can cause fi re,
electrical shock, or electrical
failure.
Uneven surface and
excessive force
Television equipment and cart
combination should be moved with
care. Quick stops, excessive force, and uneven
surfaces may cause the equipment and cart
combination to overturn.
Fire prevention
To prevent fi re, never place any
type of candle or naked fl ames on
the top or near the TV set.
TINS-D500WJZZ
07P11-MSF
E2 ACCESSORIES
The following accessories are included with this television.
Remote Control Size-AA batteries
E3

ANTENNA CONNECTION

Connecting to an antenna
TV
300-ohm
twin-lead 75-ohm
flat feeder impedance
(not supplied) converter
75-ohm coaxial cable
(round cable)
(not supplied)
Standard DIN45325
plug (IEC 169-2)
Antenna in
If your outdoor antenna uses a 75-ohm coaxial cable
with a standard DIN45325 plug (IEC 169-2), plug it
into the antenna jack at the rear of the set.
Rod antenna connection
Rod Antenna
Antenna
mounting
Feeder
socket
Impedance
Converter
Antenna
jack
• When using the RF terminal connection, set the TV to channel zero to make initial adjustments for the VCR.
• If you are using a rod antenna and the signal from TV station is weak or not clear, the picture may not display clearly
or properly. In this case, we recommend that you use an outdoor antenna.
Rod antenna (dipole) with ribbon feeder
Operation manual 300-75 impedance converter
Connecting to an antenna via a VCR
VCR
To antenna
in terminal
To RF out terminal
If your outdoor antenna uses a 300-ohm twin-lead
fl at feeder, connect a 300-ohm to 75-ohm impedance
converter and plug it into the antenna jack at the
rear of the set.
(1) Insert the rod antenna's base post into the
antenna mounting socket until it clicks into
position.
(2) Connect the feeder to the impedance
converter.
(3) Plug the impedance converter into the
antenna jack at the rear of the set.
10/25/07 11:42:21 AM 10/25/07 11:42:21 AM