Assembly; Unpacking And Checking Parts; Tools Needed - Craftsman 113.228162 Owner's Manual

permanent ground suchasto a property g rounded outlet
box.
Atemporary adapter
as illustrated is available for connecting
plugs to 2 -pro ng receptecles, The temporary adapter shou Id
be used only until a properly grounded outlet can be
installed bya qualified electrician,
GROUNDING LUG
i _ MAKE SURE THIS IS
3-PRONG _'_ [-._-_-_-_--CONNECTED
TO A
NowNGROUND
_,_-._ _ N_ L_ Jt _'_- 2-PRONG
,_,_
/ _'-_J_
RECEPTACLE
ADAPTER
NOTE: The adapter illustrated is for use only if you already
have a properly grounded 2-prong receptacle.
The use of any extension cord will cause some loss of
power. To keep this to a minimum and to prevent over-
heating and motor burn-out, use the table below to deter-
i , !l,i , _1
assembly procedure
UNPACKING AND CHECKING PARTS
PARTS TABLE
A Belt Guard Assembly ......................... 1
B Headstock ................................... 1
C Motor Pulley ................................. 1
D V-Belt ...................................... 1
E Motor ...................................... 1
F Large Toot Rest .............................. !
G Tool Rest Holder ............................. 1
H Tailstock and Ram ............................ 1
J Rear Foot ................................... 1
K Clamp Support ............................... 1
L Tube Or Bed ................................. 1
M Small Tool Rest .............................. 1
N Manual ..................................... 1
0 Loose Parts Bag Part No. 507458
(Containing the following items):
Bolt, Carriage 1/4-20x 1-3/4 ................. 4
Spur Center ................................ 1
Point Center ................................ 2
Cup Center ................................. I
Cord Clamp ................................ 2
Grip ....................................... 4
Switch Key ................................. 1
Lookwasher, Ext, #10 ........................ 4
Nut, Lock !/4-20 ............................ 4
Nut, Hex 1/4-20 ............................ 4
Nut, Sq. 1/4-20 ............................. 3
Nut, Hex Heavy 3/4-16 ....................... 1
mine the minimum wire size (A,W.G.} extension cord, Use
only 3 wire extension cords which have 3-prong grounding
type plugs and 3-pole receptacles which accept the tools
plug,
Extension Cord Length Wire Size A.W.G.
Up to 100 Ft. t6
t00- 200 Ft. 14
200- 400 Ft. 10
CHECK MOTOR ROTATION
Place the motor on your workbench or on the floor.
Standing clear of the motor shaft, plug the motor cord into a
properly grounded outlet. Notice the rotation of the shaft,
As you look directly at the motor shaft it should be turning in
the clockwise direction _ . If the motor shaft is turning
clockwise, remove the plug from the power outlet and
continue the assembly procedures, If the motor is turning
counterclockwise, remove the plug from the power outlet
and contact your Sears Store immediately.
!, !,,,,i , , ...... •.....
TOOLS NEEDED
Phillips Screwdriver
Screwdriver (Medium)
Framing Square
3/8 inch Wrench
7/16 inch Wrench
Screw, Pan Hd. Ty T 10-32 x !/2 ............. 4
Screw, Pan Hd. Ty AB #8 x 1/2 ................. 4
Shoe, Lock .................................. 2
Stud, Nut ................................... 4
Washer, 17/64 x 47/64 x 1/16 ................ 7
Wrench, Hex "L'" 3/16 ........................ 1
Wrench, Hex "'L" 5/32 ........................ 1
Handle ..................................... 4
A