Craftsman HEAVY DUTY TOOL CHESTS Operator's Manual
Craftsman HEAVY DUTY TOOL CHESTS Operator's Manual

Craftsman HEAVY DUTY TOOL CHESTS Operator's Manual

Heavy duty tool chests

Advertisement

Available languages

Available languages

OPERATOR'S
MANUAL
HEAVY
DUTY TOOL CHESTS
* Product you purchased may vary from picture shown
CALL 1o800o366o7278 FOR SERVICE PARTS. Refer to Service
Parts Drawing for futt listing of Service Parts.
LOCATING
MODEL # iNFORMATION
Model numbers and other information required for service parts is
located on a tabet on the interior right side of the top most drawer.
The maximum weight for each drawer should be no more than
110 tbs.
The maximum product weight for combined models, including
contents, should be no more than 1,500 tbs.
_
L
L±L
2
For casters, use high quality bearing grease, (yearly).
Lubricate the slides with grease or equivalent, (twice yearly.)
Lubricate tock with graphite, (yearly).
Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mitd detergent and water.
Auto wax witt preserve the unit's luster finish. Apply the wax
as to a car. The wax witt atso hetp protect the unit against
scratches.
Grease and oit can be removed with most standard
cleaning fluids. For safety, use a nonflammable
cleaning fluid.
If drawer liners are supplied, it is recommended they are used
to protect the finish inside the drawers and to make the drawers
easier to ciean. The drawer tiners may be cleaned
with soap and water.
DANGER
_
is used to indicate a hazardous situation which,
if not avoided, wit__Ji
result in serious injury or death.
WARNING
Z_
indicates a hazardous situation which,
if not avoided, could resutt in serious injury or death.
CAUTION is used to indicate a hazardous situation which, if not
avoided, _
result in minor injury, moderate injury, or property
damage.
CAUTION:
Read and follow all Safety Rules and Operating
Instructions before first use of this product.
DANGER
,_
- DO NOT stand on this product. You may fatt or cause product
to tip.
- DO NOT open more than one drawer. The product may be-
come unstable and tip.
- DO NOT step in the drawers. You may fatt or cause product to
tip.
DO NOT mount this product on a truck bed or any other mov-
ing object.
DO NOT move the product prior to closing and locking att the
drawers and chest tid. The drawers could come open and
make the product unstable and tip.
DO NOT place any objects on top of chest tid. Remove att
objects from chest tid before opening.
WARNING
z_
* WEAR SAFETY GLASSES when removing or repositioning
the stides.
- DO NOT pull the unit, push it when moving.
- USE THE BRAKES when not moving this product. This wiii
prevent the product from roiling.
- DO NOT atter this product in any manner. For example, do not
wetd externat iockbars or attach electrical equipment.
- Keep the product on ievet surfaces. The product may become
unstable and tip if stored or moved on an uneven surface.
- BE CAREFUL when ctosing the cover. Remove hands before
the cover closes completely.
CAUTION
- This product is not designed to be directly lifted with a fork lift,
or to be towed with any mechanical devices.
- The maximum weight for each drawer should never be
exceeded.
- Only transport this product empty. Properly secure when
transporting.
- DO NOT exceed maximum product weight, including contents.
See Capacities for more information.
Distributed
by Sears Brands Management Corporation,
Hoffman Estates, IL 60179
F1914

Advertisement

Table of Contents
loading

Summary of Contents for Craftsman HEAVY DUTY TOOL CHESTS

  • Page 1 OPERATOR'S MANUAL Periodically the drawer fronts, drawer trim, and other surfaces should be cleaned with a mitd detergent and water. Auto wax witt preserve the unit's luster finish. Apply the wax as to a car. The wax witt atso hetp protect the unit against HEAVY DUTY TOOL CHESTS scratches.
  • Page 2: Caster Installation

    CASTER INSTALLATION Items Needed: TOOLS REQUIRED: 5/16 - 18 x 3/4-in. Hex Screw 1!2-in Wrench 1/2-in. Wrench Cross4ip Screwdriver Process: NOTE: Use adequate for this operation. personnel NOTE: Failure to install easter angles may result in HARDWARE INCLUDED: premature cabinet failure. CABINET HARDWARE Remove bottom drawer.
  • Page 3: Installing Drawers

    Lever Style - Lift or lower (depending on the slide) the Install (2) 5/16-18 Batt Studs into top tray using (2) release lever on both sides, (this allows the slides to ride 5/16-18 Ctip-on Nut. (Bali Studs should face towards the over the stops).
  • Page 4: Removing And Installing

    REMOVING AND iNSTALLiNG SLIDES To remove the slide from the unit, first remove the drawer. After removing the drawer check to see if the unit has rivets located on the front of the slide. To drill out rivets, use a 5/324n drill bit. The rivets wilt need to be replaced with 5/324n rivets.
  • Page 5 MANUAL DE USUARIO • Lubrique la cerradura con grafito (anualmente). • Limpie con detergente suave y agua los frontales y los bordes laterales de los cajones y las demos superficies. • La cera para autom6viles preservar_ el acabado brilloso de la unidad. Aplique la cera como Io har{a al carro.
  • Page 6: Herramientas Necesarias

    INSTALACION DEL TtRADOR Elementos necesarios: HERRAMIENTAS NECESARIAS: TorniHo Hexagonal de 5/16 - 18 x 3/4 ptg Uave Inglesa de 1/2 inch Llave Inglesa de 1/2 inch Destomittador de Punta en Cruz NOTA: UtiHce personal adecuado para esta operaci6n. NOTA: No instalar Los angulos de _as ruedas giratorias puede ocasionar faHa prematura de_ gabinete.
  • Page 7 Estilo palanca - Levante o bale (dependiendo de la Instala (2) Pernos Esf6ricos de 5/16 -18 en la bande]a corredera) ta patanca de NberaciOn en ambos lados (esto superior con (2) Tuercas de Abrazadera de 5/16 - 18. permite que las correderas pasen sobre los topes.) JaJe (Los Pemos Esf6ricos deben quedar de frente at centro hacia afuera para retirar.
  • Page 8 INSTALAClON DESlNSTALClON DECORREDERAS Para quitar t acorredera detaunidad, primero q uite ta gaveta. Despu6s dequitar e lcajOn, comprueba sitaunidad t iene remaches enetfrente d elacorredera. Para quitar l os remaches conuntaladro, usaunabroca para tatadro d e 5/32 pig. D eber_s reemptazar losremaches conrem- aches d e5/32 plg.

Table of Contents