Page 1
Operator's Manual CRAFTSMAN 2.6 cu. in./42cc 2-Cycle GASOLINE CHAIN SAW Model No. 358.351380 - 18 In. Bar 358.350180 - 18 In. Bar Read and follow all Safety Rules and Operating WARNING:.: Instructions before first use of this product. For answers to your questions about this product: Call 7 am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun.
FULL ONE YEAR WARRANTY ON CRAFTSMAN ® GAS CHAIN SAW For one year from the date of purchase, when this Craftsman Gas Chain Saw is maintained, lubricated and tuned up according to the operator's manual, Sears will repair, free of charge, any defect in material or workmanship.
Page 3
• Keep caps and fasteners securely tightened. and causes the saw to move in the op- • Use only Craftsman accsssories and posite direction of the chain rotation. replacement parts as recommended. Pinch-Kickback drives the saw straight Never modify your saw.
increase the chance of kickback. Fol- keep y.our body from being in a direct I,ne with.the cutting chain. low manufacturer's chain sharpening and maintenance instructions.Check • Stand with your weight evenly bal- anced onboth feet. tension at regular intervals, but never •...
_bmneto circulation disorders or muffler and spark arresting screen normal swelling. Prolonged use in which meets the requirements of cold weather has been linked to blood Califomia Codas 4442 and 4443. All vessel damage in otherwise healthy U.S. forest land and the states of people.
Page 6
KNOW YOUR SAW READTHIS OPERATOR'SMANUALAND SAFETYRULESBEFORE OPERAT- INQ YOUR CHAIN SAW. Compare the illustrationswith your unitto lemilledze yourself with the Ioc._on of the various controlsand adjustments, save this manual for future reverence. Cylinder Cover Throttle Adjusting Chain Lookout Screw Direction Rear of Travel Handle...
For maximum guide bar and chain life, der FUELING ENGINE. we recommend you use Craftsman chain saw bar oil. If Craftsman bar 0il Is * RII bar oil tank with bar oil. Your saw not available, you may use a good will use approximately one tank of bar oll for each tank of fuel mix.
• Fullypush-inchokelever and contin- OPERATING TIPS ue to pull starter rope handle until en- • Check chain tension before first use gine starts. and after 1 minute of operation. See • Then, squeeze and release the Chain Tension in the Maintenance throttle rigger to retum engine to idle section.
Page 9
plumbor levelto determinethe di- This hinge will help prevent the tree rectionoftree lean. from falling in the wrong direction. • Weight and branches on one side. Hinge holds tree on • Surrounding trees and obstacles. stump and helps controlfall • Look for decay and rot. If the trunk is rotted, it can snap and fall toward the Opening of operator.
or woodintothe cutuntilthe sawcanbe Usln O Ii log _nd r,,._ removed easily. R estart s awandcarefully for support =--- ,.,u, ___ reenter t he cut.Donotusea metal wedge.Donotattempt t o restart y our sawwhenit is pinched or hungin a log. 1stCut Turn sawOFFanduse a plasticor wooden wedge to force cutopen.
• Once a year, replace the spark plug, air filter element, and check guide bar 1 U__ and chain for wear. A new spark plug ahd'_r-]ilter element assures proper 2 Use Craftsman chain saw bar oil air-fuel mixture and helps your engine...
CHECK FOR DAMAGED OR • Using bar tool, rollchain around guide WORN PARTS bar to ensureall linksare in bar groove. Replacement of damaged/worn p arts • Lift up tip of guide bar to check for shouldbe referredtoyour SearsSer- sag. Release tip of guide bar, then vice Center.
INSPECT MUFFLER AND SPARK • Add lubdcant to sprocket hole after each use. ARRESTOR SCREEN • Burring of guide bar rails is a normal As the unit is used, carbon deposits process of rail wear. Remove these build up on the muffler and spark burrs with a fiat file.
• Replace with Champion CJTY spark Cylinder plug and tighten with a 3/4 inch socket Cover wrench (10-12 ft-lbs). Spark plug gap Plug Boot should be .025 in. • Reinstall the spark plug boot. • Reinstall the cylinder cover and 3 Spark screws (15-20 in-lb_).
CLEAN FUEL FILTER Start motor, let it run for 3 minutes, and proceed t_>the adjustment section. If To clean fuel tilter, drain your unit by engine does not start, refer to trouble- running dry of fuel, remove fuel cap/re- shooting chart or call 1-800-235-5878. tainer assembly from tank.
Run engine at least 5 minutes after the unit before storing or transporting. adding stabilizer. • Store chain saw and fuel in a well CRAFTSMAN 40:1, 2-cycle engine oil ventilated area where fuel vapors (air cooled) is especially blended with cannot reach sparks or open flames fuel stabilizer.
TROUBLE SHOOTING CHART CAUSE TROUBLE REMEDY Engine will not • Ignition switch off. • Move Ignition switch to ON. start or will run • Engine flooded. • See "Starting Instructions." • Fill tank with correct fuel mixture. only a few •...
gine owner, you are responsible for the shall be warranted for the period performance of the required mainte- of time up to the first scheduled replace- nance listed in your Owner's Manual. ment point for that part. SEARS recommends that you retain all DIAGNOSIS - - receipts covering maintenance on your...
REPAIR PARTS ® WARNING NI repldnk adjustments and malntenm_e not delcdl)ed In the Operator's Manual rnust be performed by quail- fled service pemonnel. 2423 Des_on Ref. Plut No. Refo Part No, Part No. 530016179 Screw 530036098 Throltle Lockout i25. 530038238 j _we-_ Mounting 530_L_75 530015814...
Page 24
For _e repair or replacement;parts you need delivie'reddirectly to your home Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) Para ordenar piezas con _entrega a domicilio - 1-800-659-7084 For in-house major brand repair service Call 24 hours a day, 7 days a week 1-800-4-REPAIR (1-800-473-7247) Para pedir servicio de reparaci6n a...