Related Manuals for Husqvarna RZ4619 CA
Summary of Contents for Husqvarna RZ4619 CA
- Page 1 Operator Manual RZ4619 CA / 966503401 Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English...
- Page 2 When this product is worn out and no longer used, it should be returned to the reseller or other party for recycling. To implement improvements, specifications and designs can be altered without prior notification. Note that no legal demands can be placed based on the information contained in these instructions. Use only original parts for repairs.
-
Page 3: Table Of Contents
CoNTENTS INTRoDUCTIoN ............... 5 mAINTENANCE ............... 34 Driving and Transport on Public Roads ...... 5 maintenance Schedule ..........34 Towing ................. 5 Battery ..............36 operating ..............5 Safety System ............37 Good Service .............. 6 Tire Pressures ............37 SymBolS AND DECAlS .......... - Page 4 WARNING! Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower. Each person operating the mower must be of sound mind and body and must not be under the influence of any mind altering substance.
-
Page 5: Introduction
INTRoDUCTIoN Congratulations Towing Thank you for purchasing a Husqvarna ride-on If machine is equipped with a tow hitch, use extreme mower. This machine is built for superior efficiency caution when towing. Never allow children or others in to rapidly mow primarily large areas. A control panel or on the towed equipment. -
Page 6: Good Service
INTRoDUCTIoN Good Service Husqvarna products are sold throughout the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer. -
Page 7: Symbols And Decals
SymBolS AND DECAlS These symbols are found on the machine and in the operator’s manual. Study them carefully so that you know what they mean. WARNING! IMPORTANT INFORMATION Xxxx xxxxxx xxxxx xxxx Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxxx. - Page 8 SymBolS AND DECAlS Read Shut off engine and Keep a safe Use on slopes No passengers operator’s remove key before distance from no greater manual performing any the machine than 10° maintenance or repair work Whole body Severing of fingers Do not open or Careful backing up, Careful going...
-
Page 9: Safety
SAfETy Safety Instructions These instructions are for your safety. Read them carefully. WARNING! This symbol means that important safety instructions need to be emphasized. It concerns your safety. IMPORTANT: THIS CUTTING mACHINE IS CAPABlE of AmPUTATING HANDS AND fEET AND THRoWING oBJECTS. - Page 10 SAfETy • Do not operate the machine while under the influence of alcohol or drugs. • Watch for traffic when operating near or crossing roadways. • Use extra care when loading or unloading the machine into a trailer or truck. •...
-
Page 11: Personal Safety Equipment
SAfETy Personal Safety Equipment WARNING! When using the machine, approved personal protective equipment (shown in illustrations) shall be used. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your retailer for help in choosing the right equipment. - Page 12 SAfETy Children Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator.
-
Page 13: Safe Handling Of Gasoline
SAfETy WARNING! The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s drive belt is removed. Safe Handling of Gasoline To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. -
Page 14: General Maintenance
SAfETy General Maintenance • Never operate machine in a closed area. • Keep all nuts and bolts tight to be sure the equipment is in safe working condition. • Never tamper with safety devices. Check their proper operation regularly. • Keep machine free of grass, leaves, or other debris buildup. - Page 15 SAfETy Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, fire or eye injury. Sparking in this circuit can not occur after the chassis cable (normally negative, black) is removed from the battery. WARNING! Avoid electrical sparking and its consequences by the following...
-
Page 16: Transport
SAfETy • The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer. only use approved repair parts for the machine. • The blades are sharp and can cause cuts and gashes. Wrap the blades or use protective gloves when handling them. -
Page 17: Controls
CoNTRolS This operator’s manual describes the Husqvarna Zero driven hydraulic pumps. Using the left and right Turn Rider. The rider is fitted with four-stroke overhead steering controls, the flow is regulated and thereby the valve engine. direction and speed. Transmission from the engine is made via a belt-... -
Page 18: Steering Control Levers
CoNTRolS Steering Control Levers The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about a neutral position. furthermore, there is a neutral position, which is locked if the steering controls are moved outward. -
Page 19: Parking Brake
CoNTRolS Parking Brake IMPORTANT INFORMATION The machine must stand absolutely still when applying the parking brake. Always set the parking brake before dismounting. Release the parking brake before moving the mower. The parking brake is found on the left of the machine. Push the release button and pull the lever backward to activate the brake—push forward to release it. -
Page 20: Ignition Switch
CoNTRolS Ignition Switch The ignition key is placed on the control panel and is used to start and stop the engine. 8058-095 Ignition switch Choke Control The choke control is used for cold starts to provide the engine with a richer fuel mixture. for cold starts the throttle should be set fully forward. -
Page 21: Fuel Tank
CoNTRolS Fuel Tank Read the safety instructions before refueling. The machine has one fuel tank, located behind the left side of the seat. The tank capacity is 4 gallons (15.1 liters). Regularly check the gas cap gasket for damage and keep the cap properly tightened. -
Page 22: Fuel Shut Off Valve
CoNTRolS Fuel Shut Off Valve The fuel shut off valve is located at the left rear of the seat. The valve is off when the handle tab is turned perpendicular to the fuel line. 8011-419 IMPORTANT INFORMATION Fuel shut off valve in the CLOSED position Always raise the deck to the highest position for transport. -
Page 23: Seat Adjustment Lever
CoNTRolS Seat Adjustment Lever The seat can be adjusted lengthways. When making adjustments, the lever under the right side of the seat is pulled up, after which the seat can be moved backward or forward. 8058-101 Lengthways seat adjustment Hour Meter The hour meter displays the total operating time. -
Page 24: Operation
oPERATIoN Read “Safety Instructions” section and following Steering pages, if you are unfamiliar with the machine. To move forward and backward Training The direction and speed of the mower’s movements is effected by the movement of the control lever(s) Zero turn mowers are far more maneuverable than on each side of mower. -
Page 25: Before Starting
oPERATIoN Before Starting • Read the sections Safety Instructions and Controls before starting the machine. • Perform the daily maintenance before starting (see maintenance Schedule in the maintenance section). • Check that there is sufficient fuel in the fuel tank. •... - Page 26 oPERATIoN move the steering controls outward to the locked (outer) neutral position. 8061-026 Place controls in neutral position move the throttle to the middle position. 8058-096 Set the throttle If the engine is cold, the throttle control should be pushed forward to the choke position. 8058-097 Set the choke control...
- Page 27 oPERATIoN Press in and turn the ignition key to the start position. IMPORTANT INFORMATION Do not run the starter for more than 5 seconds 8050-780 each time. If the engine does not start, wait Turn to the start position approximately 10 seconds before retrying. When the engine starts, immediately release the ignition key back to the run position.
-
Page 28: Jumper Cables
oPERATIoN Weak Battery WARNING! Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries. IMPORTANT INFORMATION Your mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. -
Page 29: Running
oPERATIoN Running Release the parking brake by pushing the top release button in and moving the lever downward. NoTE: The mower is equipped with an operator presence system. When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine. -
Page 30: Operating On Hills
oPERATIoN Engage the mower deck by pulling out the blade switch. move throttle control to full throttle. The machine’s speed and direction are continuously variable using the two steering controls. When both controls are in the neutral position, the machine stands still. By moving both controls an equal amount forward or backward, the machine moves in a straight line forward or backward respectively. -
Page 31: Mowing Tips
oPERATIoN Mowing Tips WARNING! • observe and flag rocks and other fixed objects to avoid collisions. Clear the lawn of stones and other objects that can be thrown out by the • Begin with a high cutting height and reduce it blades. -
Page 32: Stopping The Engine
oPERATIoN Stopping the Engine If the engine has been worked hard, allow it to idle for approximately one minute in order to attain normal operating temperature before stopping. Avoid idling the engine for longer periods, as there is a risk of the spark plugs fouling. -
Page 33: Manual Transport
oPERATIoN Manual Transport When pushing or pulling the mower, engage the EZT (Integrated Zeroturn Transaxle) bypass linkages. The EZT bypass linkages are located on the rear of the frame, below the rear engine guard. Raise the deck into the highest cutting position. -
Page 34: Maintenance
mAINTENANCE Maintenance Schedule The following is a list of maintenance procedures that must be performed on the machine. for those points not described in this manual, visit an authorized service workshop. An annual service carried out by an authorized service workshop is recommended to maintain your machine in the best possible condition and to ensure safe operation. - Page 35 mAINTENANCE Daily At least Maintenance once interval each in hours year MAINTENANCE Before After ■ Check/adjust throttle cable ● ● Check the condition of belts, belt pulleys ■ ■ Change the engine oil ■ ■ Replace the engine oil filter ■...
-
Page 36: Battery
mAINTENANCE Battery STANDARD STATE APPROXIMATE BATTERY CHARGING TIME* TO FULL CHARGE AT 80 F / 27 your mower is equipped with a maintenance free BATTERY Maximum Rate at: battery and does not need servicing. However, CHARGE 50 Amps 30 Amps 20 Amps 10 Amps periodic charging of the battery with an automotive... -
Page 37: Safety System
mAINTENANCE Safety System The machine is equipped with a safety system that prevents starting or driving under the following conditions. The engine can only be started when: The mower deck is disengaged. The steering controls are in the outer, locked neutral position. -
Page 38: Parking Brake
Visually check that no damage is found on the lever, linkages, or switch belonging to the parking brake. Perform a standstill test and check that there is sufficient braking action. To adjust the parking brake, contact the Husqvarna service workshop. IMPORTANT INFORMATION The machine must be absolutely standing still when applying the parking brake. -
Page 39: V-Belts
mAINTENANCE V-belts Check every 100 hours of operation. Check for severe cracking and large nicks. NoTE: The belt will show some small cracks in normal operation. The belts are not adjustable. Replace belts if they begin to slip from wear. Deck Belt Park on a level surface. -
Page 40: Cutting Blades
Torque blade bolt to 90 ft/lbs (122 Nm). IMPORTANT INFORMATION 8058-027 Special blade bolt is heat treated. Blade Blade bolt (special) Replace with a Husqvarna bolt if required. Cutter housing Do not use lower grade hardware than Blade attachment specified. -
Page 41: Adjusting The Mower Deck
mAINTENANCE Adjusting the Mower Deck Leveling deck Adjust the deck while the mower is on a level surface. make sure the tires are inflated to the correct pressure. See “Technical Data” under Transmission. If tires are under or over inflated, the deck cannot be properly adjusted. -
Page 42: Anti-Scalp Rollers
mAINTENANCE Anti-scalp rollers Anti-scalp rollers are properly adjusted when they are just slightly off of the ground when the deck is at the desired cutting height in the operating position. Anti-scalp rollers then keep the deck in the proper position to help prevent scalping in most terrain conditions. -
Page 43: Cleaning
mAINTENANCE Cleaning Regular cleaning and washing, especially under the IMPORTANT INFORMATION mower deck, will increase the machine’s life-span. make it a habit to clean the machine directly after use Use protective glasses when (after it is cooled), before the dirt sticks. cleaning and washing. -
Page 44: Lubrication
lUBRICATIoN Lubrication Schedule 8058-105 12/12 Every year lubricate with grease gun lubricate with oil can 1/52 Every Week oil change level check 1/365 Every day filter change General Remove the ignition key to prevent unintentional Wipe away excess grease after lubrication. movements during lubrication. -
Page 45: Front Wheel Mount
2-3 strokes per spindle. 8058-106 Deck spindle Transmission The transmission is maintenance free with no need for level checks or oil changes. If a leak occurs, replace the unit or contact your Husqvarna dealer. -
Page 46: Troubleshooting
TRoUBlESHooTING Problem Cause Engine will not start • Blade switch is engaged. • Steering controls are not locked in the neutral position • Parking brake is not activated • Battery is dead • Contamination in the carburetor or fuel line. •... - Page 47 TRoUBlESHooTING Problem Cause Engine overheats • Clogged air intake or cooling fins • Engine overloaded • Poor ventilation around engine • Defective engine speed regulator • Too little or no oil in the engine • Contamination in the carburetor or fuel line. •...
-
Page 48: Storage
Drain the fuel into Always use genuine Husqvarna spare parts. an approved container outdoors and An annual check-up at an authorized service far away from open flame. Never workshop is a good way to ensure that your machine use gasoline for cleaning. -
Page 49: Schematics
SCHEmATICS... -
Page 50: Technical Data
TECHNICAl DATA RZ4619 CA / 966503401 Engine manufacturer Briggs & Stratton Type Power 19 hp* lubrication Pressure with oil filter oil capacity excluding filter 1.34 qts / 1.27 liters oil capacity including filter 1.46 qts / 1.38 liters Engine oil (See viscosity diagram) - Page 51 TECHNICAl DATA RZ4619 CA / 966503401 Frame Cutting Width 46" / 117cm Cutting Height 1.5 - 4" / 3.8 - 10.2 cm Uncut Circle Number of Blades Blade length 22¾" / 57.8 cm Nose Rollers Sprung Seat Standard Hinged Arm Rests...
-
Page 52: Torque Specifications
TECHNICAl DATA Torque Specifications Engine crankshaft bolt 50 ft/lb (67 Nm) Standard ¼" fasteners 9 ft/lb (12 Nm) Deck pulley bolts 150 ft/lb (203 Nm) Standard " fasteners 18 ft/lb (25 Nm) lug nuts 75 ft/lb (100 Nm) Standard " fasteners 33 ft/lb (44 Nm) Blade bolt 90 ft/lb (122 Nm) -
Page 53: Conformity Certificates
CoNfoRmITy CERTIfICATES CE requirements USA requirements The Declaration of Conformity is included in the labels are placed on the engine and/or in the engine literature packet. compartment stating that the machine will fulfill the requirements. This is also applicable to special requirements for any of the states, (California emission rules etc.). -
Page 54: Service Journal
SERVICE JoURNAl Date, mtr reading, stamp, sign Action Delivery Service Charge the battery. Adjust the tire pressure of all wheels to 15 PSI (1 bar). mount the steering controls in the normal position. Connect the contact box to the cable for the seat’s safety switch. Check that the right amount of oil is in the engine. - Page 55 SERVICE JoURNAl SERVICE JoURNAl Date, mtr reading, stamp, sign Date, mtr reading, stamp, sign Action Action After the first 5-8 hours Change the engine oil. Action Date, mtr reading, stamp, sign 25-Hour Service Check the fuel pump’s air filter. Sharpen/Replace mower blades if required. Check the tire pressures.
- Page 56 SERVICE JoURNAl SERVICE JoURNAl Date, mtr reading, stamp, sign Date, mtr reading, stamp, sign Action Action 50-Hour Service Perform the 25-hour service. Clean/replace the air cleaner’s filter cartridge (paper filter (shorter intervals for dusty operating conditions). Change engine oil. lubricate according to lubrication chart. Check/adjust the parking brake.
- Page 57 SERVICE JoURNAl SERVICE JoURNAl Date, mtr reading, stamp, sign Date, mtr reading, stamp, sign Action Action 300-Hour Service Perform the 25-hour service. Perform the 50-hour service. Perform the 100-hour service. Check/adjust the mower deck. Clean the combustion chamber and grind the valve seats. Check the engine valve clearance.
- Page 58 SERVICE JoURNAl Date, mtr reading, stamp, sign Action...
- Page 60 P/N 115 314727R1 01/19/10...