Page 1: Notice For Users In The Usa
A shielded I/F cable is required to insure compliance with FCC regulation for Class B computing equipment. * As an Energy Star Partner, SHARP has determined that this product meets the Energy Star guidelines for energy efficiency. Declaration of Conformity...
Page 2 Sharp Plaza, Mahwah, New Jersey 07430 TEL: 1-800-BE-SHARP About the Modem This equipment PC-9800T complies with Part 68 of FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment.
Page 3 If trouble is experienced with this equipment, please contact Sharp Electronics Corp. for repair and (or) warranty information (Refer to the end of this section). If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved.
Page 4 Discard used batteries according to the manufacturer's instructions. Copyright It is the intent of Sharp that this product be used in full compliance with the copyright laws of the United States and that prior permission be obtained from copyright owners whenever necessary.
Page 5 Mahwah, NJ 07430...
Page 6: Notice For Users In Canada
Notice for Users in Canada About Modem The REN is 0.3. The Industry Canada label identifies certified equipment. This certification means that the equipment meet certain telecommunications network protective, operational and safety requirements. The department does not guarantee the equipment will operate to the user's satisfaction.
Page 7 Load Numbers of all the devices does not exceed 100.” Product Information and Customer Assistance For Product Information and Customer Assistance: Call: 1-905-890-2100 Sharp Electronics of Canada Ltd. 335 Britannia Road East, Mississauga, Ontario, L4Z 1W9 Canada...
Page 8: Notice For Users In Australia
SHARP is not in a position to authorise the copying or broadcasting of copyright materials and nothing in this OPERATION MANUAL should be implied as giving that authority.
Page 9: Notice For Users In The Uk
Copyright Recording and playback of any material may require consent, which SHARP is unable to give. Please refer particularly to the provisions of the Copyright Act 1956, the Dramatic and Musical Performers Protection Act 1958, the Performers Protection Acts 1963 and 1972...
Page 10: Notice For Users In Europe
Notice for Users in Europe This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG- Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE.
Page 11 Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som komplette ras av 93/68/EEC. Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC. Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/EEC.
Page 12 CAUTION: TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD AND THE BATTERY BEFORE SERVICING. CAUTION: FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG AND THE BATTERY. VORSICHT: UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN UND DIE BATTERIE ÈNTFERNEN. ATTENTION: POUR UN ARRET TOTAL DU SYSTEME, DECONNECTEZ LA PRISE DE COURANT SECTEUR.
Page 13: Safety Precautions
Safety Precautions General • Follow all cautions and instructions which may be marked on the notebook. • Except as described elsewhere in this manual, refer all servicing to qualified personnel. Immediately shut off the notebook and refer for servicing under the following conditions: when the power cord or plug is damaged or frayed •...
Page 14 • Check the AC power cord and power connectors periodically for damage. Replace the power cord immediately if damage is found. • Never subject your notebook to sudden shocks or extreme vibration. • Do not drop the notebook nor hit it with other equipment. •...
Page 15 • Charge the battery pack only with the AC adapter included with your notebook. Discharging • Do not use the battery pack for any purpose other than powering the notebook computer. Storage • Store the battery pack in a cool and dry place. Never allow the temperature to exceed 60°C (140°F) during storage.
Page 16 • Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. • Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. • Use caution when installing or modifying telephone lines. •...
Page 17: About This Manual
Information in this manual is subject to change without notice and does not represent a commitment on the part of SHARP Corporation. SHARP Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
Page 18: Recording Important Information
Recording Important Information For future reference, please record the following information in the spaces provided below. Model Number: Serial Number: BIOS Version Number: Date of purchase: Dealer’s Name: Place of purchase: Password: The serial number is printed on a sticker located on the bottom of the notebook.
Page 19: Manual Conventions
Manual Conventions This manual uses a set of style conventions described below. Notes and Cautions are italicized with icons: A note icon informs you of a special technique or information that may help you perform a task or better understand a process.
Page 20 Refer to Infrared Communication section in Chapter 5.
Page 21: Indicator Panel
Appearance of the Notebook Each number after the arrow indicates the page referring to the part. General View LCD Screen → 1-3, 4-1 Microphone Status Indicators → 2-1 Power Switch → 1-4 Keyboard → 2-5 GlidePoint → 2-3 Stereo Speakers PC Card Slot Slide Door →...
Page 22: Table Of Contents
Right External Microphone Jack → 4-7 Audio Output Jack → 4-6 Audio Input Jack IR Port → 5-1 CD Tray Eject Hole → T-3 CD-ROM Drive → 2-13 Modem Jack → 5-4 (US & Canada only) Left PC Card Slots → 6-1 Hard Disk Drive Floppy Disk Drive →...
Page 23 Bottom Left-side bay lock latch Right-side bay lock latch → 2-8 → 2-7 Ventilation Openings Do not cover) Legs You can tilt the notebook by rotating its legs.
Page 24 Table of Contents Notice for Users in the USA..............i Notice for Users in Canada ..............iv Notice for Users in Australia.............. vi Notice for Users in the UK..............vii Notice for Users in Europe............... viii Safety Precautions ................x About This Manual................
Page 25 Chapter 4: Peripherals Display....................4-1 Printer ....................4-3 Keyboard/Mouse................4-4 Audio System..................4-6 Universal Serial Bus .................4-8 Chapter 5: Communication Functions Infrared Communication..............5-1 Modem (US and Canada only) ............5-4 Chapter 6: Hardware Expansion PC Cards ...................6-1 Memory Module ................6-6 Chapter 7: Using the Passwords Passwords ..................7-1 Security Slot..................7-3 Chapter 8: Setup Utility...
Page 26: Appearance Of The Notebook
Appearance of the Notebook Each number after the arrow indicates the page referring to the part. General View LCD Screen → 1-3, 4-1 Microphone Status Indicators → 2-1 Power Switch → 1-4 Keyboard → 2-5 GlidePoint → 2-3 Stereo Speakers PC Card Slot Slide Door →...
Page 27: Pc Card Slots →
Right External Microphone Jack → 4-7 Audio Output Jack → 4-6 Audio Input Jack IR Port → 5-1 CD Tray Eject Hole → T-3 CD-ROM Drive → 2-13 Modem Jack → 5-4 (US & Canada only) Left PC Card Slots → 6-1 Hard Disk Drive Floppy Disk Drive →...
Page 28 Bottom Left-side bay lock latch Right-side bay lock latch → 2-8 → 2-7 Ventilation Openings Do not cover) Legs You can tilt the notebook by rotating its legs.
Page 29: Chapter 1: Quick Setup
CHAPTER 1 Quick Setup Your notebook is designed and pre-configured for easy setup and use. This chapter describes the steps to get your notebook up and running as quickly as possible. Read this chapter first.
Page 31: Unpacking The Notebook
• TranXit Quick Reference Guide • SuperVoice User’s Guide (only in US and Canada) • Sharp Import/Export User’s Guide (not available in Germany) • Profilink Windows (only in Germany) • Notice to Users Carefully inspect each component to make sure nothing is missing or damaged. If any of these items is missing or damaged, notify your dealer immediately.
Page 32: Connecting To Ac Power
Connecting to AC Power Your notebook works with either the rechargeable battery or AC power. See the next chapter for more information on power sources. Before using the notebook for the first time: Make sure the notebook is turned off. Connect the notebook and the AC adapter with the adapter cable.
Page 33: Opening The Notebook
Opening the Notebook To open your notebook, Slide the display lock latch until the screen cover releases, and raise the cover. Tilt the cover to a comfortable viewing position. Display Lock Latch Figure 1-2. Opening the Screen Cover Quick Setup 1-3...
Page 34: Turning Power On
Turning Power On To turn on the power, Make sure your notebook is connected to the AC Power. When using the notebook the first time, be sure to connect it to an AC power. If you use the battery instead, the Windows 95 setup may not be able to finish when the battery does not have enough power.
Page 35: Setting Up Windows 95
Setting up Windows 95 The first steps in the setup process are as follows: • Gathering information • Configuring your computer • Restarting your computer To set up Windows 95, follow the instructions on the screen. See also the manual of Windows 95.
Page 36: Setting Original Wallpaper
After setting up Windows 95, set the SHARP original wallpaper in the following procedure. Double-click the Click me to set up SHARP Wallpaper icon at the upper right corner of the screen. When the message appears, click OK. The SHARP original wallpaper is displayed on the screen.
Page 37: Shutting Down The System
Shutting Down the System To turn off the notebook: From the Start menu, select Shut Down. Click Yes, and the notebook turns off automatically. If you have not saved a file, a dialog box will appear asking if you want to save it or not.
Page 38: Chapter 2: Basic Operations
CHAPTER 2 Basic Operations This chapter describes the basic operations you can perform on the notebook.
Page 40: Choosing Power Source
Choosing Power Source You can use the notebook with one of the following power sources: • AC power from a wall outlet • Rechargeable battery pack Use AC power whenever possible; rely on the battery pack only when AC power is not available.
Page 41: Resetting The System
Resetting the System You may need to reset the system after adding hardware or software so that your notebook will recognize the newly installed devices or software. When a message appears after the installation, click OK, Yes, etc. to restart Windows 95. You can also restart Windows 95 from the Start menu.
Page 42: Operating Glidepoint
Operating GlidePoint Your notebook is provided with an integrated pointing device called GlidePoint. Through GlidePoint, you can move the pointer, select an item among the menu, etc. just like with a mouse. GlidePoint is also compatible with a PS/2 mouse. •...
Page 43: Changing The Configuration
Click, Double-click, and Right-click To click, double-click, or right-click, you can use the left or right button just like those of a mouse. Instead of clicking by pressing the left button, you can just tap gently anywhere on the rectangular pad of the GlidePoint. For double-clicking, tap twice gently.
Page 44: Using Keyboard
Using Keyboard Your notebook, equipped with the Windows Enhanced Keyboard, provides all the functionality of a full-sized desktop keyboard. You should familiarize yourself with the special notebook function keystrokes. Windows Logo Keys Opens the Windows Start menu. Provides application-specific short-cut menu equivalent to the right-clicking.
Page 45 Increases the LCD screen brightness. Decreases the LCD screen contrast (only for DSTN models). Increases the LCD screen contrast (only for DSTN models). Turns on and off the battery low warning beep. Turns on and off the screen backlighting. Puts the notebook in suspend mode (to RAM or to Disk, according to the setup selection).
Page 46: Installing Units Into Bays
Installing Units into Bays When shipped, your notebook is equipped with the CD-ROM drive in the right-side bay and with the floppy disk drive in the left-side bay. You can uninstall these drives and install other units such as the battery pack and the AC adapter. •...
Page 47 Insert the unit into the bay with the connector forward. When the unit is correctly installed, you hear a clicking sound, and the bay lock latch returns to the original position. Left-side Bay The left-side bay is installed with the floppy disk drive when the notebook is shipped.
Page 48 Installing and Uninstalling the Floppy Disk Drive After installing or uninstalling the floppy disk drive, you have to change the settings as follows. After installing the floppy disk drive: Turn on the notebook. When the message Press <F2> to enter SETUP appears, press F2. In the Main menu, set the item of Diskette A: to 1.44 MB, 3 1/2.
Page 49: Using Floppy Disks
Using Floppy Disks You can use double-density (2DD) 720KB or high-density (2HD) 1.44MB floppy disks. Handling Floppy Disks • Do not open the shutter and touch the disk inside; otherwise, you will not be able to read or write data to the disk. •...
Page 50: Formatting A Floppy Disk
Always insert a floppy disk straight into the notebook. When inserting the disk into the notebook, make sure it is not upside down. Do not push the disk into the notebook by excessive force. Removing Make sure the floppy disk drive indicator is off. Press the eject button to pop out the disk slightly.
Page 51: Backing Up Data
Backing Up Data We recommend that you regularly backup the data on your hard disk drive in case. Windows 95 has a backup function to let you easily back up your data. From the Start menu, select Programs - Accessories - System Tools - Backup to start the backup operation.
Page 52: Cd-Rom Drive →
Using CD Compact disc (CD) is a storage medium with which you can read data, play music, install and run programs, etc. The CD-ROM drive is available in the right-side bay of your notebook. Handling CDs • Do not write on either side of the disc, particularly the non-label side. Data is read from the non-label side.
Page 53: Removing A Cd
Gently push the CD tray back into the notebook. • When inserting a CD, do not use force. • Make sure the CD is correctly inserted into the tray, then close the tray. • Do not leave the CD tray open. Also, avoid touching the lens in the tray.
Page 54: Chapter 3: Battery And Power Management
CHAPTER 3 Battery and Power Management This chapter explains how to manage the notebook's power effectively and use optional battery packs.
Page 56: Battery Pack
If not, the system may malfunction or the data may be lost • Incorrect installation of the battery is dangerous. Replace the battery only with Sharp's optional battery packs. Discard used batteries according to the dealer's instructions. The procedure for recharging an optional battery pack is the same as the standard battery.
Page 57: Charging The Battery
Connect the notebook to the AC adapter and fully charge the battery pack. • If you connect the notebook to wall outlet while discharging the battery, the initialization is cancelled. • You cannot initialize two battery packs at the same time. Charging the Battery Turn off the notebook.
Page 58: Low Battery Indication
Low Battery Indication When the battery power becomes significantly low, the battery charge indicator ) blinks red and the warning beep sounds. To stop the beep, press Fn + F10. When the low battery power is indicated, connect the notebook to a wall outlet quickly.
Page 59: Power Management
Power Management The power management saves electricity and extends battery life by controlling power supply to built-in devices. In power management are the following four modes: • Idle mode • Stand-by mode • Suspend-to-RAM mode • Suspend-to-disk mode Switching to Each Mode If you do not input any data through the keyboard or GlidePoint, your system enters a power management mode, depending on the duration of no operation.
Page 60: Idle Mode
Idle Mode Your notebook enters the idle mode if you do not use the keyboard, GlidePoint, the mouse, the hard disk, or the serial port for about ten seconds. In the idle mode, the CPU speed is decreased. When you begin using the notebook again, the CPU will resume its normal speed.
Page 61 • You open the screen cover and press any key if the system enters the suspend mode by closing the cover (as long as the battery voltage is sufficient), or • The modem receives a call (in US and Canada only). If you do not want to resume your system by calling: 1.
Page 62 Suspend-to-Disk Mode The Suspend to Disk mode saves the current condition in an area of hard disk, which is called ‘‘suspend-to-disk partition,’’ and the notebook is automatically turned off. Your notebook enters the Suspend to Disk if: • The time specified in the Setup Utility has passed without any operation, •...
Page 63 Setting Power Configuration You can configure power management settings in the Power menu of the Setup Utility. Figure 3-1. Setup Utility Power Configuration Screen Power Management Enables or disables power management. Hard Disk Power Down After Specifies a period of inactivity after which the system does not supply power to the hard disk drive.
Page 64 Hot-Key Suspend Data to Switches whether the system enters the Suspend to RAM or Suspend to Disk when you press Fn + F12. Cover Close Specifies the status when the cover is closed. Since Windows 95 periodically accesses the hard disk and automatically writes to the display, the Auto Suspend functions above sometimes do not work.
Page 65: Windows Power Management
Windows Power Management Besides the power management features you can adjust in the Setup Utility, your notebook complies with the Windows power management called Advanced Power Management (APM). Through APM, your notebook selectively powers down system components that are not in use. To adjust the Windows power management, From the Start menu, select Settings - Control Panel.
Page 66: Chapter 4: Peripherals
CHAPTER 4 Peripherals This chapter describes how to use peripheral devices of your notebook. You can connect a printer, external monitor, external keyboard, mouse, or any other device to the parallel, RS-232C serial or keyboard/mouse ports.
Page 68: Display
Display You can use a CRT monitor as an external monitor. To display only on a CRT monitor, use a VGA-compliant model or model with 1024x768 or higher resolution. To display on CRT and LCD simultaneously, use a model with 1024x768 or higher resolution.
Page 69 • If you select True Color in the Color Palette, * The drawing speed of screen is decreased, * The screen seems corrupted when displaying video or animation, and * The screen cannot display when you use a ZV port compliant PC card. Connecting a CRT Monitor Follow the instructions below to use a CRT monitor with the notebook.
Page 70: Printer
Printer Before using the printer, read the printer manual. Connecting a Printer Turn off the notebook and the printer. Open the connector compartment cover on the rear side of the notebook. With a 25-pin cable, connect the printer to the parallel port of your notebook. If the connector has screws, tighten them.
Page 71: Keyboard/Mouse Port →
Keyboard/Mouse Connecting a Keyboard or PS/2 Mouse If you wish to use a full size desktop keyboard or external PS/2 mouse with your notebook, follow the instructions below. Turn off the notebook. Connect the cable from your mouse or keyboard to the keyboard/mouse port on the left side.
Page 72: Rs-232C Serial Port →
Connecting a Serial Mouse Turn off the notebook. Open the connector compartment cover on the rear side. Connect the serial mouse to the RS-232C serial port. Tighten the screws if they are present. RS-232C Serial Port Figure 4-4. Connecting a Serial Mouse Turn on the notebook.
Page 73: Audio Input Jack →
Audio System Connecting audio equipment Turn off the notebook and any connected peripherals. Use the following audio cable for the connection: To output the notebook’s audio signal to the audio equipment: Audio Equipment Notebook Black LINE IN (R) Audio Output White Jack LINE IN (L)
Page 74: External Microphone Jack →
Connecting an external microphone Turn off the notebook. Connect the external microphone to the external microphone jack on the right side. Figure 4-6. Connecting an External Microphone Turn on the notebook. When using an external microphone, you cannot use the built-in microphone.
Page 75: Usb Port →
Universal Serial Bus Your notebook has a new interface called Universal Serial Bus (USB). This interface unifies the connection between computers and peripheral devices such as keyboards, mice, speakers, modems, and printers. Through the USB, you could connect/disconnect the peripherals without turning off the notebook. See manuals of peripheral devices supporting USB.
Page 76: Chapter 5: Communication Functions
CHAPTER 5 Communication Functions This chapter explains how to use infrared communications and the built-in modem.
Page 78: Infrared Communication
Place the target device so that its IR port is in line with that of the notebook. Adjust the distance between the IR ports to less than 30 inches (80 cm). When using a Sharp electronic organizer, make sure the two IR ports are within 4 inches (10 cm) apart.
Page 79 Setting for Each Application The settings for each communications software are different as below; however, most of them are automatically done. Communications software IR Type Physical Port Logical Port TranXit (Variable mode) IrDA COM2 Disabled Zrlink COM2 COM4 Import/Export (not available in Germany) COM2 COM4 Profilink (only in Germany)
Page 80 Select SHARP IR for Window 95 Version X.X. Click Add/Remove; then, OK; then, Yes to restart the notebook. The SHARP 4M Infra-Red Port is detected. Follow the instructions on the screen. Re-install Infrared Support for Window 95 Version X.X and SHARP IR for Window 95 Version X.X.
Page 81: Modem Jack →
Modem (US and Canada only) You can use the built-in modem for data transfer, fax communication and voice communication. Connecting the Modem to Telephone Line Turn off your notebook. Connect one end of the included modem cable to the modem jack on the right side of your notebook.
Page 82 In the Power menu, set Power Management to Disabled. Press Esc, select Save Changes & Exit, and press Enter. After the notebook restarts, turn off the Windows power management (see Chapter 3). Using communications software Do not enter suspend mode while using communications software. You have to set parameters such as modem speed (baud rate) and line type (pulse dialing or tone dialing) within the communications software you are using.
Page 83: Chapter 6: Hardware Expansion
CHAPTER 6 Hardware Expansion This chapter describes how to handle PC cards and increase memory of the notebook.
Page 85: Pc Cards
PC Cards Your notebook is equipped with two PC card slots which can accommodate two Type II or one Type III card(s) conforming to the standards of the PCMCIA (Personal Computer Memory Card International Association). When using a PC card, see its manual. Inserting PC Cards You can insert/eject PC cards in the same way as floppy disks.
Page 86: Ejecting Pc Cards
Some PC cards for ATA devices such as a hard disk may not be recognized correctly. In this case, see your Windows manual or call the SHARP customer assistance center for technical support and specific installation instructions.
Page 87 ZV-Port Compliant PC Card To use a ZV-port compliant PC Card, you need to install CardWorks. When not using ZV-port compliant PC Cards, uninstall CardWorks. Installing CardWorks From the Start menu, select Programs - Accessories - Notepad. From the File menu, select Open. In the field of File name, type: C:\CONFIG.SYS and click Open.
Page 88 • If you cannot use a ZV-port compliant PC Card after the above procedure, install the other version of CardWorks, which is stored at: R:\PCCARD95\OLD in the backup CD-ROM.The ZV-port compliant card may function. • To adjust the screen, select My Computer - C: - Vpmutil - Adjust. Uninstalling CardWorks From the Start menu, select Programs - Accessories - Notepad.
Page 89 17. Repeat the above steps to remove another Cirrus Logic PD6832 CardBus Controller. 18. Click Refresh. 19. Make sure both of Cirrus Logic PD6832 CardBus Controller are attached with the X marks. 20. Click Close; then, Yes. 21. Restart the system. To use other PC cards, you need the following settings after the above steps: From the Start menu select Settings - Control Panel.
Page 90: Memory Module
Memory Module Your notebook comes with 32MB of memory. You can expand the memory size by installing a pair of 4MB, 8MB or 16MB memory modules. Standard Memory Modules Total 4MB x 2 40MB 32MB 8MB x 2 48MB 16MB x 2 64MB Installing a Memory Module •...
Page 91 Turn over the notebook to the ordinary position, and open the display panel. Remove the memory compartment cover by pressing down and then out. Figure 6-3. Removing the Compartment Cover Raise the tape attached on the memory module board until it snaps up, and gently draw out the module board.
Page 92 With the connector face down, insert the board until the end of the board is matched with the two lines on the slot. Connector Figure 6-6. Inserting the Memory Module Connector part Two lines Figure 6-7. Connector Part and Two Lines 10.
Page 93: Using Passwords
CHAPTER 7 Using Passwords This chapter describes how to set up security to limit access to the notebook.
Page 95: Passwords
Passwords If you set a password, only a person who knows the password can use certain functions of your notebook. The password feature protects your data from unauthorized access and helps prevent computer virus infections. Two types of passwords (the supervisor password and the user password) limit the following access in different levels: •...
Page 96: Deleting A Password
Figure 7-1. Setup Utility Security Configuration Screen Setting Up the User Password To set the user password, you have to set the supervisor password first. Open the Security menu of the Setup Utility as in the previous subsection. Select Set User Password with the arrow key, and press Enter. Type your user password, and press Enter.
Page 97: Security Slot
Security Slot You can prevent theft by using a security cable and the security slot on the rear side of your notebook. Figure 7-2. Security Slot Using Passwords 7-3...
Page 98: Chapter 8: Setup Utility
CHAPTER 8 Setup Utility This chapter describes how to run the Setup Utility to change settings on your notebook.
Page 100: Running The Setup Utility
Running the Setup Utility With the Setup Utility, you can customize the system configuration information, such as time and date, port assignments, passwords, or power management settings. The information you have specified is saved in a special area called CMOS RAM, and the system reads it every time you turn on the notebook.
Page 101: Using The Setup Utility
Using the Setup Utility You can use the following keys: Moves the cursor from one menu to another. Moves the cursor from one item to another in a menu. Moves the cursor to the first or last item. Increases the numeric value or changes to the next value of an item.
Page 102 Settings That You Can Change Main menu In the Main menu of the Setup Utility, you can change the following settings: Figure 8-1. Setup Utility Main Configuration Screen System Time Defines the system time, using the format hour:minute:second (24- hour format). Press Enter to move the cursor. You can also change the system time in the Windows Control Panel.
Page 103: Power-On Self Test
Boot Sequence Specifies where the boot program looks for operating system files. When you select A: then C:, for example, the system checks the floppy disk drive first, and if no system disk is found in the drive, the system boots from the hard disk drive.
Page 104: Advanced Menu
Advanced menu In the Advanced menu of the Setup Utility, you can change the following settings: Figure 8-2. Setup Utility Advanced Configuration Screen COM1/COM2 Specifies the serial communication devices assigned to COM1 and COM2. IR Mode Specifies the mode of the IR Port. Select IrDA1.1 in ordinary usage. LPT Extended Mode Specifies the mode of the printer port among Output Only, Bi-Directional, EPP and ECP.
Page 105 When this item is Yes, you cannot use a PC card in the MS-DOS mode. Keyboard NumLock Defines whether you can use the NumLock keys on the built- in keyboard when you connect an external keyboard. GlidePoint(PS/2 Mouse) Defines whether you can use GlidePoint and a PS/2 mouse.
Page 106: Security Menu
Security menu In the Security menu of the Setup Utility, you can change the following settings. See also the previous chapter about setting the password. Figure 8-3. Security Menu Supervisor Password is Defines whether a supervisor password is required. If Password on boot is enabled and if this item is enabled, you have to input the supervisor password when the system boots.
Page 107 Password on boot Defines whether the system requires passwords on boot time. If this item is enabled, you need to input the password to start the operation. If this item is disabled, you can start the operation without any passwords; however, you cannot access the floppy disk drive if Diskette access is set to Supervisor.
Page 108 Power menu In the Power menu of the Setup Utility, you can change the following settings. See also the Chapter 3 on power management and battery. Figure 8-4. Power Menu Power Management Enables or disables the power management of your notebook, not Windows 95 power management.
Page 109 Auto Suspend-to-Disk After Defines the duration before your notebook enters the Suspend to Disk. Hot Key Suspend Data to Defines whether the system enters the Suspend to RAM or Suspend to Disk when you press Fn+F12 or when you close the cover screen. If you do not set the next item, Cover Close, to Suspend, however, the system does not enter the suspend mode when you close the screen.
Page 110 Exit menu In the Exit menu of the Setup Utility, you can select one of the following items. Figure 8-5. Exit Menu Save Changes & Exit Saves the settings you have changed and exits the Setup Utility. Discard Changes & Exit Exits the Setup Utility without saving the settings you have changed.
Page 111: Troubleshooting
Troubleshooting This chapter describes how to troubleshoot notebook problems.
Page 113 Common Problems Problems with your notebook can be caused by something as minor as an unplugged power cord or as major as a damaged hard disk drive. The information in this troubleshooting section is designed to help you find and solve minor problems. If you still have a problem after trying all the suggested remedies in this chapter, contact your dealer.
Page 114 T-2 Troubleshooting...
Page 115 Question: Why does the power switch not function? • Make sure the AC power cable is correctly connected to a live wall outlet. • The power switch does not accept just a light touch. Press the switch firmly. • If the notebook is operating with a battery, the battery may be discharged.
Page 116 • If you cannot do the software reset, turn the notebook off, wait more than ten seconds, and turn the notebook back on. Question: Why is the battery discharged so quickly? • Initialize the battery pack. T-4 Troubleshooting...
Page 117 Confirm the CD is not stained or scratched. Question: Why can I not play files from a compact disc? • If you are using Sharp Player, confirm the CD or files are supported. Question: Why does the CD-ROM drive not open? •...
Page 118: System Mapping
Figure T-1. Inserting a Fine Rod Question: Why do I get a non-system disk or disk error message? • You may have inserted a non-bootable disk in Drive A: (either a defective disk or one without an installed operating system). Remove the disk.
Page 119 • Check whether the notebook and the printer are connected correctly. • Check whether the printer has enough paper. • From the Start menu, select Settings - Printers to confirm your printer is installed here. If not, click Add Printer to install your printer.
Page 120 • Confirm the monitor is connected correctly. • Make sure the CRT monitor is selected as the display by pressing Fn+F5. • Make sure the value of the Desktop area in the Display Properties dialog box is lower than the resolution of the CRT monitor. Question: Why is the CRT display corrupted? •...
Page 121 • Confirm the item of the GlidePoint in the Advanced menu of the Setup Utility is Enabled. • If a PS/2 mouse is connected to the notebook, the GlidePoint does not work. Remove the PS/2 mouse. Question: Why can I not communicate through the built-in IR port? •...
Page 122 Question: Why does the “Autotyping” message appear when I start the notebook? • You may have installed or uninstalled the floppy disk drive without changing the settings. To change the setteings, see page 2-9. T-10 Troubleshooting...
Page 123 Index jack A AC adapter 1-2, 2-1 external monitor port jack xix, 4-2, AC cord AC power indicator xviii, 2-1 advanced menu of setup F floppy disk 2-9, 2-10, T-3 utility floppy disk drive advanced power management indicator xviii installing 3-10 audio equipment uninstalling...
Page 124: Pin Assignment
scroll lock indicator xviii security menu of setup utility M main menu of setup utility memory module 6-6, A-9 security slot microphone xix, 7-3 xviii serial mouse modem (only in US and setup utility Canada) advanced menu 5-4, T-6 exit menu jack 8-11 xix, 5-4...
Page 125 V ventilation openings W warm boot Windows logo keys power management 3-10 setting up Start menu Z ZV-port compliant card Index 3...

Sharp PC-9800T Manual

Chapter 1: Quick Setup

Chapter 2: Basic Operations

Chapter 3: Battery and Power Management

Chapter 4: Peripherals

Chapter 5: Communication Functions

Chapter 6: Hardware Expansion

Chapter 7 : Using the Passwords

Chapter 8: Setup Utility

Quick Links

Notice for Users in the USA

Declaration of Conformity

Related Manuals for Sharp PC-9800T

Summary of Contents for Sharp PC-9800T

Table of Contents