Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for NEC FS-8002
Summary of Contents for NEC FS-8002
-
Page 1: Instruction Manual
COLOR TELEVISION INSTRUCTION MANUAL FS-8002... -
Page 2: Table Of Contents
To adjust the headphone volume To adjust the sound balance Size To adjust sound frequency Reveal To select sound effect Enjoying stereo and bilingual broadcasts Hold Cancel Stereo programs Subcode Bilingual programs Specification Using other menus NEC Service Centres To set clock... -
Page 3: Safeguards
SAFEGUARDS To operate your receiver at the peak performance, please read this Instruction Manual carefully and retain it for the future reference. M Water and Moisture : Never install the set in the following places : in the bathroom, in a wet basement(Dripping or splashing water). -
Page 4: Introduction
INTRODUCTION Features Double Window You can enjoy two programs simultaneously by splitting the screen in two. 16:9 screen You can select a desired 16:9 (wide screen) screen mode for movies as well as the normal 4:3 picture mode. A variety of AV terminals for external equipment connection. MTwo sets of video / audio inputs on the rear and one set on the front. -
Page 5: To Connect The Aerial
Installation To connect the aerial Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and positioning of the aerial will depend upon your particular area. Notes M When using an outdoor aerial, disconnect the leads of the indoor aerial, if connected, from the aerial terminal socket. -
Page 6: Identification Of Controls
Identification of controls * The following describes the name of each part of the TV and remote control. FRONT VIDEO 3 input terminals (S-VIDEO, VIDEO, AUDIO L, R) Main power switch Digital EYE sensor Use this Jack when listening to the sound outputted to the speaker POWER with the headphone, and you can... - Page 7 BACK This always provides with TV signal output of the selected channel. R-AUDIO-L VIDEO Video 1 input terminals R-AUDIO-L VIDEO(DVD-Y) Cr-DVD-Cb VIDEO 2(SCART JACK) input / output terminal (SCART does not supports S-VIDEO) A/V OUT OF SCART TERMINAL will provide with TV signal output of the selected channel.
-
Page 8: Remote Control
REMOTE CONTROL TV / VIDEO / DVD INPUT SELECT POWER ON / OFF TEXT RECALL PR SELECT 0~9 (PAGE SELECTOR 0~9) SLEEP TIME SELECT SELECTABLE PICTURE HEADPHONE CHANNEL LOCK VOLUME UP / DOWN SELECTABLE SOUND WIDE / ZOOM SELECT SYSTEM MENU SOUND EFFECT STEREO / BILINGUAL... -
Page 9: Turning The Power On/Off
TURNING THE POWER ON / OFF MThe following describes how to turn the TV on / off using the main switch and the remote control. Turning the power on / off Turning the power on / off The following describes how to turn the TV on / off using the main switch and the remote control. -
Page 10: Tuning The Tv Channels
TUNING THE TV CHANNELS AUTO SETUP SYSTEM AUTO SETUP SYSTEM 1. Press the MENU button to select to INSTALL. 2. Press the C / B buttons and then INSTALL SYSTEM. 3. Select AUTO SETUP with the PRy / x buttons and the C / B buttons to start AUTO SETUP. -
Page 11: Edit
EDIT 1. Press the menu button to select INSTALL. 2. Press the C / B buttons and then INSTALL SYSTEM. 3. Select EDIT with the PR y / x buttons and press the C / B buttons to start EDIT. 4. -
Page 12: Convenient Picture Control
CONVENIENT PICTURE CONTROL You can select the picture quality instantly. TO SELECT THE PICTURE MODE 1. Press the SELECTABLE PICTURE NORMAL NICAM STEREO ( ) button at remote control to select - - : - - the desired picture quality. Normal, Mild and Favourite can be selected cyclically. -
Page 13: Enjoying Wide And Zoom Picture
ENJOYING WIDE AND ZOOM PICTURE You can enjoy WIDE picture and ZOOM 1~ZOOM 4 picture with TV. In addition to regular wide / zoom screen mode. TO SELECT THE WIDE OR ZOOM 1~ZOOM 4 SCREEN 1. By pressing the WIDE / ZOOM button in remote control, the following six modes change cyclically. -
Page 14: Convenient Sound Control
CONVENIENT SOUND CONTROL You can select and adjust the sound quality as you like. TO VOLUME CONTROL Adjust the volume with the volume Down / Up button on the upper of the set, or with the C / B buttons on the remote control. VOLUME TO MUTE THE SOUND The muting function is convenient when you need to pay attention to... -
Page 15: To Select The Sound Mode
TO SELECT THE SOUND MODE 1. Press the SELECTABLE SOUND SPEECH ) button to select the desired MONO - - : - - sound quality. NORMAL, FAVOURITE, MUSIC, SPEECH can be selected cyclically. 2. Or press the MENU button to select the SOUND and then to be displayed on the right appearance. -
Page 16: To Adjust The Sound Balance
TO ADJUST THE SOUND BALANCE Press the MENU button to select the SOUND and then to be displayed on right appearance. Select the BALANCE with the PR y / x buttons. Adjust the BALANCE with the C / B buttons. Press C button to decrease the right speaker volume and the B button to decrease the left speaker volume. -
Page 17: Enjoying Stereo And Bilingual Broadcasts
ENJOYING STEREO AND BILINGUAL BROADCASTS The unit receivers both stereo and bilingual broadcasts transmitted in either the NICAM or German stereo / bilingual broadcasts system. Stereo Programs Press the STEREO / BILINGUAL SELECT PR08 )button to select to nicam- MONO - - : - - stereo / mono mode. -
Page 18: Using Other Menus
USING OTHER MENUS TO SET CLOCK 1. Press the MENU button to select the FEATURES and then to be displayed right appearance. 2. Select the CLOCK with PR y / x buttons. 3. Press the C / B buttons to activate the hour or the minute and preset the hour or minute with the direct(0~9) buttons. -
Page 19: To Turn On The Tv Automatically(Wake Time)
TO TURN ON THE TV AUTOMATICALLY(WAKE TIME) With the CLOCK, the WAKE TIME, the WAKE PR. Preset, the TV will automatically turn on to a preset program number at a reset time. Select the WAKE TIME with PR y / x buttons. Then, press direct key(0~9) to set the wake up time. -
Page 20: Sleep Time Setting
SLEEP TIME SETTING PR04 1. When this button, up to 2 hours every 20 minutes can be set to MONO the sleep timer. SLEEP 2. If you press the SLEEP button for the first time, SLEEP 0 sign of the non set sleep-timer appears on the upper left side of the screen. -
Page 21: To Select The Screen Color
TO SELECT THE SCREEN COLOR When no signal is being received, the TV will automatically turn blue or red at the time SCREEN BLUE or SCREEN RED on. 1. Press the MENU button to select the and then to be displayed on the right appearance. -
Page 22: To Select The Auto Volume Control
TO SELECT THE AUTO VOLUME CONTROL Different sound source (eg. Advertisement during movies) fairly often do not have the same volume level. In the case, you can equalize the volume with the AVC(auto volume control) ON. 1. Press the MENU button to select the FEATURES and then to be displayed on the right appearance. -
Page 23: Watching Picture In Picture
The unit is capable of displaying two picture with the small sub picture simultaneously. This is called the Picture-In-Picture function. A TV picture or a picture from external source equipment such as a VTR can be displayed as another picture. MODE SUB CH UP SUB CH DOWN... -
Page 24: To Watch A Tv Or An External Source As A Sub-Picture
TO WATCH A TV OR AN EXTERNAL SOURCE AS A SUB-PICTURE 1. Select the desired program. 2. Press the PIP button to display a sub-picture. SUB-PICTURE 3. Press the sub TV / VIDEO button repeatedly to select the input for the sub picture(the small picture). -
Page 25: To Switch The Main And Sub Picture Of The Pip
TO SWITCH THE MAIN AND SUB-PICTURE OF THE PIP Press the SWAP button when a picture-in-picture is displayed. The main picture(the large picture) and sub-picture(the small picture) are switched. Press the SWAP button again to switch again. TO FREEZE THE SUB-PICTURE Press the STILL button when a sub-picture is displayed. -
Page 26: To Connect Other Machines Like Video
CONNECTING OTHER MACHINES LIKE VIDEO AUDIO SET CAMCORDER GAME PLAYER LASER DISC PLAYER NAMES AND FUNCTIONS OF CONNECTIVE TERMINALS VIDEO 2 Input/Output terminal (Scart Jack Input/Output) This always provides with TV signal output of the selected R-AUDIO-L VIDEO channel. Input terminals of VIDEO1 (picture, sound on left, right) R-AUDIO-L VIDEO(DVD-Y) -
Page 27: Connecting Video
CONNECTING VIDEO When connecting other equipment, please ensure you turn the main switch OFF to prevent any damage to the equipment. L When connecting the VIDEO to the back of the TV 1. Prepare the connective plug for picture / sound. 2. -
Page 28: Connecting At Av2(Scart)
CONNECTING AT AV2(SCART) When connecting other equipment, please ensure you turn the main switch OFF to prevent any damage to the equipment. L Connecting to a HI-FI STEREO VIDEO(STEREO mode is defaulted) 1. Prepare the connective plug for picture / sound. 2. -
Page 29: Connecting With S Picture Video
L Connecting SCART to SCART(STEREO mode is defaulted) 1. Prepare the connective plug for picture / sound. 2. Connect the SCART input/output terminal of VIDEO with the SCART input/output terminal of TV. REAR SCART TERMINAL SCART INPUT/ OUTPUT HI-FI STEREO VIDEO CONNECTING WITH S PICTURE VIDEO When connecting other equipment, please ensure you turn the main switch OFF to prevent any damage to the equipment. -
Page 30: Connecting With Video Camera(Camcorder)
CONNECTING WITH VIDEO CAMERA(CAMCORDER) When connecting other equipment, please ensure you turn the main switch OFF to prevent any damage to the equipment. L To connect VIDEO CAMERA with the TV M When watching a recording by VIDEO CAMERA, it’s convenient to connect with the TV front connector. 1. -
Page 31: Connecting With Audio Set
CONNECTING WITH AUDIO SET When connecting other equipment, please ensure you turn the main switch OFF to prevent any damage to the equipment. MWhen listening to sound in powerful AUDIO, while watching the picture on TV. MConnect external input terminal of AUDIO to right & left sound output of TV signal. R-AUDIO-L VIDEO R-AUDIO-L... -
Page 32: Connecting Dvd Player
CONNECTING DVD PLAYER When connecting other equipment, please ensure you turn the main switch OFF to prevent any damage to the equipment. MWhen connecting the DVD player. 1. Prepare the connective plug for picture / sound. 2. Connect the DVD-Y output terminal of DVD player with the DVD-Y input terminal of TV. 3. -
Page 33: Viewing Teletext(Option)/Use Of The Teletext Buttons
VIEWING TELETEXT(OPTION) / USE OF THE TELETEXT BUTTONS M The teletext service is carried on a TV transmission signal, therefore it is only available when a TV program can be received on your TV. Your choice of TV program also governs which Teletext service you will receive. TO SELECT THE TEXT MODE First, turn on your TV SET and choose your TV program. -
Page 34: Reveal
REVEAL Some Teletext pages play a role in concealing part of the display in, for example, a quiz page with concealed answer. The REVEAL button releases the concealed text as long as the REVEAL button is not again. HOLD Some Teletext pages contain more information than can be displayed simultaneously and are therefore sub-divided into a series of two or more pages. -
Page 35: Specification
SPECIFICATION TV Standard PAL / SECAM, NTSC 3.58 / 4.43(AV) Color system B / G, D / K, I, M, H Sound system Rated voltage 110-240V~, 50 / 60Hz Power consumption 148W Sound Output Power MAIN: 8W X 8W HYPER + CHINA + IVORY COAST Channel Coverage VHF L : E2(48.25MHz)~S6(147.25MHz) VHF H : S7(147.25MHz)~S36(423.25MHz) -
Page 36: Nec Service Centres
Western Australia Perth 45 Sarich Court, Osborne Park 6017 (08)9445 5901 For Service in outer areas, please contact your NEC retailer for the address of the nearest Authorized NEC Service Centre. NEC Australia Pty. Ltd. 244 Beecroft Road EPPING 2121...