Page 1
Before Using the Remote Control Inserting the Batteries Using the Remote Control Remote Control Operating Range Setup Screen Size and Setting-up Distance Setting-up Methods Connecting to a Video Source Connecting to a Computer Printed in Japan 402171600 (9002555) 02.02-.6A(C05)
Inserting the Batteries The batteries are not inserted into the remote control at the time of purchase, and so you need to insert them before the remote control can be used. Remove the battery compartment cover. While pressing the cover here, lift the cover up. Insert the batteries.
Using the Remote Control Set the R/C switch on the remote control to the ON position. Remote control light-receiving area Point the remote control light-emitting area toward one of the remote control light- receiving area on the projector and operate the remote control buttons.
Remote Control Operating Range (illumination) button When the button is pressed, the buttons shown in colour in the illustration at left are illuminated for 10 seconds. If you press the button while the buttons are illuminated, the illumination will illumination continue for a further 10 seconds.
Screen Size and Setting-up Distance The distance between the projector and the screen determines the actual image size. Recommended distance : 0.9m - 12.4m (3.0 - 40.7 ft.) While referring to the table below, position the projector so that the image size is smaller than the screen size.
Setting-up Methods The projector supports the following five projection methods, allowing you to choose the best method for displaying your images. After setting up the projector, refer to the User's Guide for details on turning on the power and adjusting settings such as the screen size. ("Basic Operations"...
Turn off the power for both the projector and the video source before connecting them. If the power for either device is on at the time of connection, damage may result. Check the shapes of the cable connectors and the device ports before making the connections.
Page 8
After making the connections, change the "Comp2/YCbCr Input" in the "Setting" menu to either "YCbCr" or "YPbPr" to match the signals from these devices. ("Setting" menu in User's Guide ) After making the connections, change the "Audio Input" setting in the "Audio"...
Projecting Composite Video Images When connected via a 3RCA A/V cable To Audio 2 port (white/red) To Video port (yellow) yellow To video output port (yellow) To audio output L port (white) white To audio output R port (red) 3RCA A/V cable (commercially-available) When connected via an RCA video cable and a stereo mini-pin audio cable To Audio 1 port...
Projecting S-Video Images When audio output is via a 2RCA audio cable To Audio 2 port (white/red) To S-Video port To video output white port S-Video cable (commercially-available) To audio output L port (white) To audio output 2RCA audio cable (white/red) R port (red) (commercially-available) When audio output is via a stereo mini-pin audio cable...
Projecting RGB Video Images When connecting to the Computer 2/Component Video port (Example: When audio output is via a 2RCA audio cable) To Computer 2/Component Video port To RGB output white port Computer cable (optional) To audio output L port (white) 2RCA audio cable (white/red) To Audio 2 port To audio output...
Page 12
Continued on the back page RGB video is only compatible with sync-in-green signals. This can be checked by looking at "Sync. Mode" in the "About" menu. After making the connections, change the "Comp1 Input" or "Comp2 /YCbCr Input" setting in the "Setting" menu to "RGB Video". For separate sync (separate H-SYNC and V-SYNC) signals, set to "Analog-RGB".
Page 13
Turn off the power for both the projector and the computer before connecting them. If the power for either device is on at the time of connection, damage may result. Check the shapes of the cable connectors and the device ports before making the connections.
Page 14
If connecting using a computer cable To Computer2/Component Video port To monitor port Computer cable (optional) If more than one external component is connected to the projector, change the "Comp2/YCbCr Input" or "Comp1 Input" setting in the "Setting" menu to "Analog-RGB" after making the connections. ("Setting"...
Playing Sound from the Computer When audio output is via a 2RCA audio cable To audio output L port (white) To audio output R port (red) white To Audio 2 port (white/red) 2RCA audio cable (white/red) (commercially-available) When audio output is via a stereo mini-pin audio cable To audio output port Stereo mini-pin audio cable To Audio 1 port...
Page 16
To USB port When audio output is via a USB cable To USB port USB cable (commercially-available) After making the connections, change the "Audio Input" setting in the "Audio" menu to either "Audio1", "Audio2" or "USB", depending on which input port you are using. ("Audio" menu in User's Guide ) The USB cable can only be connected to computers with a standard USB interface.
Using the Remote Control to Operate the Mouse Pointer The accessory remote control can be used as a wireless mouse. To USB mouse port To USB port USB cable (commercially-available) Once the connection has been made, the mouse pointer can be operated as follows.
Page 18
The USB cable can only be connected to computers with a standard USB interface. If using a computer which is running Windows, the computer must have had a full version of Windows 98/2000/Me installed. If the computer is running a version of Windows 98/2000/Me that has been upgraded from an earlier version of Windows, correct operation cannot be guaranteed.
Connecting to an External Monitor To Monitor Out port Cable provided with monitor Monitor port A commercially available adapter might be required for connecting a Macintosh computer. Digital RGB signals that are being input to the Computer 1 port cannot be output to an external monitor.
Page 20
Name and function of the projector operating panel buttons [Help] button [Power] button Displays the online help menu to assist you if you have Turns the projector power on and off. a problem. [Video] button [Computer/YCbCr] button Changes the image source between the Video port and Changes the image source between the Computer 1 port the S-Video port.
Page 21
Name and function of the remote control buttons Underneath cover Remote control light-emitting area Outputs infrared remote control signals. Indicator [Freeze] button [Menu] button Keeps the current computer or video image on the Lights when a remote control signal is being Displays or hides the environment setting menus.