NEC VT45 Quick Connect Manual

Quick Connect Guide
Connections
Step 1
Connect the supplied 15pin-15pin signal cable.
For older Macintosh computers, use a
commercially available pin adapter to
connect to your Macintosh's video port.
S-V IDE
O
IN
VID
EO
IN
Monitor
Step 2
Connect the supplied power cable.
PC
ROL
CONT
OUT
RGB
OUT
L/MON O
IN
RGB IN
IN IN
IN
R
IN
AC IN
Step 3
Turn on the projector.
Step 4
Set up the Projector.
To adjust the projector's lens shift, focus or to zoom in and out use
the Lens Shift, Focus ring or Zoom lever on the lens.
To optimize image, press the AUTO ADJUST button on the cabinet
or the remote control.
AU
DIO
L/M
IN ON
O
OU T R G
RG
R B OU B O
IN T
PC
IN U T
Using the Lens Shift
RG B IN R G
B IN
1 Grip the lens shift lever on the top and bottom.
2 Hold the lever to move the lens vertically or horizontally.
See page E-14 for Lens Shift Adjustable Range.
Power down all equipment
before making connections.
Adjusting the Tilt Foot
1 Press and hold the Tilt button on the front of the projector.
2 Lift the front edge of the projector to the desired height, and release the button to lock the Adjustable Tilt
Foot.
• If the projected image does not appear square to the screen then use keystone correction for proper adjustment.
Power button
NOTE: To turn off the projector,
press and hold the POWER button
for a minimum of two seconds.
Focus ring
Zoom lever
1
2
OL PC
CONTR
RGB OUT
OUT
L/MONO
IN RGB IN
IN IN
R IN
IN
IN
AC
1
PC
CONTR OL
OUT
RGB
OUT
L/MONO
IN RGB IN
2
IN IN
R IN
IN
IN
AC
1
Printed in China

Remote Control Features

RGB VIDEO S-VIDEO POWER
3
4
AUTO ADJ.
MAGNIFY VOLUME
5
7 PICTURE FREEZE MUTE ASPECT 10
8
MENU HELP
12
11
13
14 15
ENTER CANCEL
RD-372E
1
Infrared Transmitter
Direct the remote control toward the remote sen-
sor on the projector cabinet.
2
Power Button
Use this button to turn your projector on and off.
NOTE: To turn off the projector, press and hold
the POWER button for a minimum of two seconds.
3
Source Buttons
Press to select an input device.
4
Auto Adjust Button
Use this button to adjust Position-H/V and Pixel
Clock/Phase for an optimal picture.
5
Magnify ( + / – ) Buttons
Use the (+) or (–) button to adjust the image size
up to 400%.
NOTE: The POWER, AUTO ADJ., MENU, SELECT, ENTER and CANCEL buttons on the remote control perform the same
7N8P0891
functions as the corresponding buttons on the projector cabinet. The remaining buttons are on the remote control only.
6
Volume ( + / – ) Buttons
1
Press and hold (+) to increase the volume.
Press and hold (–) to decrease the volume.
7
Picture Button
2
Press to display the Picture adjustment menu. Each time
this button is pressed, the highlight will move as follows:
...
Brightness Contrast Color Hue Sharpness
You can also select the Picture adjustment item by using
the select up or down button.
If no adjustments are performed within 3 seconds, the
Picture adjustment menu will disappear.
6
8
Freeze Button
Press to freeze a picture. Press again to resume motion.
9
9
Mute Button
This button turns off the image and sound. Press again to
restore the image and sound.
10
Aspect Button
Press to display the Aspect Ratio select menu.
Each time this button is pressed, the current aspect ratio
will change as follows:
...
Normal Zoom Wide Zoom Cinema Normal
You can also select the aspect ratio by using the Select
button.
If no adjustments are performed within 3 seconds, the
Aspect Ratio select menu will disappear.
11
Menu Button
Displays the menu.
12
Help Button
Provides information about the current signal and the status
of the projector.
13
Select ( ) Buttons
: Use these buttons to select the menu of the item
you wish to adjust.
: Use these buttons to change the level of a selected
menu item.
A press of the button executes the selection.
14
Enter Button
Use this button to enter your menu selection.
15
Cancel Button
Press this button to close menu.