Related Manuals for Fujitsu FLASH-CAN-100
Summary of Contents for Fujitsu FLASH-CAN-100
-
Page 1: User Guide
Fujitsu Microelectronics Europe FMEMCU-UG-900001-32 User Guide F²MC-16LX FAMILY EVALUATION BOARD FLASH-CAN-100 USER GUIDE... -
Page 2: Revision History
21.07.99 V2.1 Schematic of board added to this manual 05.08.99 V2.1 Attached Floppy modified to incl. Softune Worbench Projects see \readme.txt – Revision V1.2 UG-900001-32 Change even page title here Revision History - 2 - © Fujitsu Microelectronics Europe GmbH... - Page 3 07/02/03 V3.0 Disclaimer corrected V3.1 Series support, device list corrected 27.11.06 V3.2 Changed Socket Information This document contains 20 pages. © Fujitsu Microelectronics Europe GmbH Change odd page title here Revision History 1.1. Regarding connectivity (MB90470) added Hardware: - 3 - problems added.
-
Page 4: Warranty And Disclaimer
Product or parts thereof, if the Product is returned to Fujitsu Microelectronics Europe GmbH in original packing and without further defects resulting from the customer´s use or the transport. -
Page 5: Table Of Contents
8 SILK-PLOT OF THE BOARD ... 17 9 SCHEMATIC OF THE BOARD ... 18 10 RELATED PRODUCTS ... 19 11 INFORMATION IN THE WWW... 20 © Fujitsu Microelectronics Europe GmbH Change odd page title here Contents - 5 - UG-900001-32... -
Page 6: Overview
The "Flash/CAN100"-board was developed in order to support customers and allow a fast software design start. Fujitsu emulators require a target system that provides Vcc and GND as well as an oscillation circuit. Additionally most of Fujitsu’s flash microcontroller support the burn-in flash programming algorithm. -
Page 7: Features
< external reset via RS232 < Flash-Programming Software for PC’s The target board will be delivered with the MB90F598G single-CAN, 128KByte flash microcontroller. This microcontroller contains the 'burn-in'-boot loader for programming the flash. © Fujitsu Microelectronics Europe GmbH - 7 - UG-900001-32... -
Page 8: Supported Microcontroller Series
= MB90V580, MB90F583, MB90583, etc. < MB90590G = MB90V590G, MB90F594/A/G, MB90594/A/G, MB90591/G, etc. < MB90595G = MB90V595, MB90F598, MB90598, etc. * modifications are necessary for FlashCAN100P-M06: see chapter 5.1 UG-900001-32 Change even page title here - 8 - © Fujitsu Microelectronics Europe GmbH... -
Page 9: Deliverables
< 1 socket adapter cover < documentation < Flash programming utility – floppy disc For software add-ons please contact your local technical support team for the latest software release or Flash-Programming tools. © Fujitsu Microelectronics Europe GmbH - 9 - UG-900001-32... -
Page 10: Configuration Of The Evaluation-Board
Pin 74 Pin 97 Pin 98 Pin 74 n.a. n.a. - 10 - © Fujitsu Microelectronics Europe GmbH CAN2 n.a. n.a. Pin 72 Pin 71 (Not supported by Jumper 3-6 !) n.a. n.a. n.a. n.a. - Page 11 MB90590 UART0 MB90595 UART1 Table 2: MCU pin-number used, for the asynchronous boot-loader software © Fujitsu Microelectronics Europe GmbH Change odd page title here SIN / Jumper handwire Pin 88 – JP10.2 (Not supported by Jumper JP7 - JP10) Pin 21 (JP10:1-2) Pin 21 (JP10:1-2) handwire Pin 27 –...
-
Page 12: Modifications For Use With Mb90470 / Mb90480 Series
Caution with the probe-cable: The probe-cable MB2132-457 (Yamaichi socket) can NOT be used for dual voltage (Vcc3=+3V, Vcc5=+5V), because Pin 23 and Pin 84 (Vcc3 / Vcc5) are shortcut within the probe-cable. UG-900001-32 - 12 - © Fujitsu Microelectronics Europe GmbH... -
Page 13: Schematic Of The Modifications For Mb90470 / Mb90480
Change odd page title here Chapter 5 Configuration of the Evaluation-Board 5.1.1 Schematic of the modifications for MB90470 / MB90480 © Fujitsu Microelectronics Europe GmbH - 13 - UG-900001-32... -
Page 14: Using The Asynchronous Boot-Loader
Chapter 6 Using the Asynchronous Boot-Loader 6 Using the Asynchronous Boot-Loader The asynchronous boot-loader SW from Fujitsu can be used to program a blank flash microcontroller. This tool is available on the floppy disc. The following additional steps to chapter 5 need to be taken to set up the hardware (power supply disconnected!): 1. -
Page 15: Connectors
7.1 Power connector (X1) The following figure shows the power connection jack X1. This connector is used to connect an external unregulated DC power supply voltage (9V-12V DC) to the evaluation board. Connector X1: It is recommended to use 9V to keep the power dissipation to a minimum. Otherwise, an additional heat sink for the linear voltage regulator might be necessary. -
Page 16: Uart (X4)
(Check that Pin 8 of U4 and Pin 8 of U5 are grounded.) UG-900001-32 Change even page title here Chapter 7 Connectors Connector X4: Connector X2, X3: - 16 - © Fujitsu Microelectronics Europe GmbH GND DTR RxD TxD CTS RTS DSR CANL CANH... -
Page 17: Silk-Plot Of The Board
Change odd page title here Chapter 8 Silk-Plot of the board 8 Silk-Plot of the board Silk Plot of the new FLASH-CAN2-100P-M06 © Fujitsu Microelectronics Europe GmbH - 17 - UG-900001-32... -
Page 18: Schematic Of The Board
Change even page title here Chapter 9 Schematic of the board 9 Schematic of the board UG-900001-32 - 18 - © Fujitsu Microelectronics Europe GmbH... -
Page 19: Related Products
< FLASH-CAN2-100P-M06 < MB2132-464 < MB2141A/B < MB2145-507 < MB90Vxxx < MB90Fxxx © Fujitsu Microelectronics Europe GmbH Change odd page title here Chapter 10 Related Products Evaluation-board according to this user guide Probe cable for socket: Yamaichi IC149-100-x14-y5 Yamaichi: http://www.yamaichi.de... -
Page 20: Information In The Www
11 Information in the WWW Information about FUJITSU MICROELECTRONICS Products can be found on the following Internet pages: Microcontrollers (8-, 16- and 32bit), Graphics Controllers Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://www.fme.gsdc.de/gsdc.htm Memory products: Flash, SDRAM and FRAM http://www.fme.fujitsu.com/products/memory/index1.html...