KitchenAid KUDD01DPPA Product Manual

PRODUCT MODEL SERIES
KUDD01DPPA
Electrical: A 120-volt, 60 Hz, AC-only, 15-amp
fused electrical supply is required. (Circuit breaker
or time-delay fuse is recommended.) It is
recommended that a separate circuit serving only
this appliance be provided.
The 3 prong grounded outlet must be installed
within 6" (15.2 cm) to 18" (45.7 cm) of the cabinet
side wall.
If you plan to install a garbage disposer, an
additional separate 120-volt, 60 Hz, AC-only,
15- or 20-amp fused electrical supply is required.
Water: A hot water line with 4.3-145 psi
(30-1000 kPa) water pressure must be used.
Water temperature must be minimum 120°F
(49°C) at dishwasher. An easily accessible valve
with 3/8" compression fitting must be installed in
the hot water supply line.
DRAIN OPTIONS
Sink drain waste
drain hose
tee connection
support
water supply
27-1/2" – 32-1/4"
(70 cm – 82 cm)
Because Whirlpool Corporation policy includes a continuous commitment to improve our
products, we reserve the right to change materials and specifications without notice.
®
Undercounter Dishwasher
OVERALL DIMENSIONS
30" ***
(76.2 cm)
CABINET OPENING DIMENSIONS
*IMPORTANT: Custom wood door panels, if
used, may be wider than the dishwasher to
match surrounding cabinets. The 23-5/8"
(60.0 cm) must be increased so that there is
a 1/4" (6.4 mm) clearance between the
cabinet side and panel edge.
For corner installation, there must be a 1/2"
(12.7 mm) space between the adjacent
cabinet doors (i.e. door knobs) and open
dishwasher drawer.
drain hose
support
waste tee
waste
22-7/16" *
(57 cm)
raised tabs for
optional top
attaching brackets
20-15/32"
(52 cm)
drawer open
Garbage disposal
connection
6" (15.2 cm)
minimum
garbage
disposal
valve
waste
water supply
8" (20.3 cm) min. bend
radius from valve
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
23-7/16"
(59.5 cm)
32-3/16"- 34-1/2"
(81.8 cm - 87.8 cm)
* If custom wood panels are to be used,
the product depth is specified with an
11/16" (18 mm) door panel thickness.
side
** Toe panel depth: Factory supplied,
attaching
2– 4-3/8" (5 – 11 cm); Custom wood,
tabs
5" (12.7 cm) less the toe panel
thickness for integrated. Minimum
panel thickness using the supplied
screws is 3/8" (9 mm).
*** Door front height: Factory supplied –
30" (76.2 cm); Custom wood – 28-1/4"
2"– 4-3/8" **
(71.8 cm) minimum.
(5 cm – 11 cm)
NOTE: Product shown with front panels
for dimension purposes.
moisture protection tape
Utility hole:
1-1/2" (3.8 cm) dia.
hole, either side –
immediately adjacent
to corner.
22-7/8"
(58.0 cm)
23-5/8"* (60.0 cm)
Air break connection
air break
drain hose
connector
valve
water supply
8" (20.3 cm) min. bend
radius from valve
4"
(10 cm)
32-5/16"– 34-5/8"
(82.0 cm – 88.0 cm)
waste
Ref. 8546448
12-2-04