Page 1
DCR-TRV8/TRV8E/TRV10/TRV10E RMT-808/809/811/812 SERVICE MANUAL Ver 1.0 1999. 04 US Model Canadian Model DCR-TRV8/TRV10 AEP Model UK Model Australian Model Chinese Model DCR-TRV8E/TRV10E E Model Hong Kong Model DCR-TRV8/TRV8E/TRV10/TRV10E Photo: DCR-TRV10 RMT-811 Tourist Model D300 MECHANISM DCR-TRV10/TRV10E DCR-TRV8/TRV10: NTSC model For MECHANISM ADJUSTMENTS, refer to the “DV MECHANICAL...
Page 2
MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
TABLE OF CONTENTS SERVICE NOTE Superimposing a still picture in a memory stick on a moving picture– M. CHROM/M. LUMI/C. CHROM ······················ 1-27 POWER SUPPLY DURING REPAIRS ····························· 6 Preventing accidental erasure – Image protection ··············· 1-28 TO TAKE OUT A CASSETTE WHEN NOT EJECT Writing a print mark –...
Page 4
• FP-91 (TOP/END SENSOR), FP-92 (TAPE LED), Order of Adjustments ······················································ 5-7 FP-242 (S/T REEL SENSOR) Subjects ··········································································· 5-7 PRINTED WIRING BOARDS ····················· 4-33 1-2. INITIALIZATION OF B, C, D, E, F PAGE DATA ········ 5-8 • VC-217 (MECHANISM CONTROL)(8/11) 1-2-1.
Page 5
3-1-1. Equipment Required ····················································· 5-36 Switch check (1) ···························································· 5-59 3-1-2. Precautions on Adjusting ·············································· 5-37 Switch check (2) ···························································· 5-60 3-1-3. Adjusting Connectors ···················································· 5-38 Record of Use check ······················································ 5-60 3-1-4. Connecting the Equipment ············································ 5-38 3-1-5. Checking the Input Signals REPAIR PARTS LIST (Except AEP/UK model) ··············································...
SERVICE NOTE POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so that the unit cannot operate. This following two methods are available to prevent this. Take note of which to use during repairs.
SELF-DIAGNOSIS FUNCTION SELF-DIAGNOSIS DISPLAY SELF-DIAGNOSIS FUNCTION When problems occur while the unit is operating, the counter of the When problems occur while the unit is operating, the self-diagnosis viewfinder, LCD screen or LCD window consists of an alphabet function starts working, and displays on the viewfinder, LCD screen or LCD window what to do.
SELF-DIAGNOSIS CODE TABLE Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Condensation. Remove the cassette, and insert it again after one hour. Video head is dirty. Clean with the optional cleaning cassette. Non-standard battery is used. Use the info LITHIUM battery. LOAD direction.
Page 51
2-10.MS SHASSIS, CONTROL SWITCH BLOCK (PS-4550) Note for installing the operation switch block (PS-4550) 3 Two tapping screws (M1.7 3.5) 4 Control switch block (PS-4550) When installing the operation switch block (PS-4550), align the switch of the area A with the power button on the cabinet (L) side.
2-12.LCD, CONTROL SWITCH BLOCK 3 Slide the panel lock knob backward and open the LCD panel. 8 LCD assembly 6 FP-91 flexible board CN8606 6P (CK-84 board) 5 Harness (PC-112) CN8604 13P (CK-84 board) 7 Two screws (M1.7) lock ace 1 Three tapping screws (M1.7 3.5)
Page 53
2-13.SERVICE POSITION (Mainly for voltage measurement and check) Firstly: Remove the respective parts by referring to "Disassembly 2-2 through 2-4, and 2-6 through 2-9". Then, connect them as shown. Adjustment remote commander (RM-95) JK-170 board Cabinet (L) assembly Lens assembly CPC-8 tarminal board jig (J-6082-388-A) F panel assembly...
DCR-TRV8/TRV8E/TRV10/TRV10E SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. VC-217 BOARD (4/11) CAMERA REC/PB Q1500 E 0.12Vp-p Q1501 E 0.22Vp-p !º Q1502 E 0.28Vp-p !¡ Q1503 E 0.34Vp-p !™ Q1504 E 0.45Vp-p !£ IC1502 8 3.0Vp-p 13.5MHz...
Page 65
DCR-TRV8/TRV8E/TRV10/TRV10E DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. VC-217 BOARD (5/11) CAMERA REC/PB !¢ IC1600 !¢ (X1600) 1.8Vp-p 24.58MHz DV PROCESS 4-21 4-22 4-23 VC-217 (5/11)
Page 66
DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. VC-217 BOARD (6/11) !∞ IC1816 1267 CAMERA REC 3.5Vp-p 6.8msec !§ IC1816 @¶ PB 0.3Vp-p 6.8msec !¶ IC1900 !¡ CAMERA REC 2.2Vp-p 25nsec REC/PB HEAD AMP 4-25...
Page 67
DCR-TRV8/TRV8E/TRV10/TRV10E DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. VC-217 BOARD (7/11) CAMERA REC/PB @£ !• IC1200 @∞ IC1402 @∞ LINE REC (NTSC) 0.44Vp-p 0.45Vp-p @¢ !ª IC1402 @ª IC1200 #£ LINE REC (NTSC) 0.37Vp-p 0.34Vp-p...
Page 70
DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. VC-217 BOARD (10/11) CAMERA REC/PB $º IC2204 $º (X2200) 2.8Vp-p 20.0MHz $¡ IC2204 %£ (X2201, C2232) 3.0Vp-p 32.767kHz HI CONTROL 4-41 4-42 4-43 4-44 VC-217 (10/11)
Page 71
DCR-TRV8/TRV8E/TRV10/TRV10E FP-82 (VC-CK CONNECT) PRINTED WIRING BOARD For schematic diagram ¥ Refer to page 4-48 for printed wiring board. — Ref. No. FP-82 Flexible Board; 10,000 Series — FP-82 BOARD CN41 CN42 For printed wiring boards • This board is two-layer print board. However, the pat- terns of layers two have not been included in the dia- gram.
Page 72
DCR-TRV8/TRV8E/TRV10/TRV10E VC-217 (FOCUS/ZOOM MOTOR DRIVE, CAMERA, BLOCKING COMPRESS, VIDEO INTERFACE, DV PROCESS, REC/PB HEAD AMP, VC-217 BOARD (SIDE A) VIDEO IN/OUT, MECHANISM CONTROL, SERVO, HI CONTROL, AUDIO) PRINTED WIRING BOARD — Ref. No. VC-217 Board; 10,000 Series — C205 C1512...
Page 73
DCR-TRV8/TRV8E/TRV10/TRV10E VC-217 (FOCUS/ZOOM MOTOR DRIVE, CAMERA, BLOCKING COMPRESS, VIDEO INTERFACE, DV PROCESS, REC/PB HEAD AMP, VIDEO IN/OUT, MECHANISM CONTROL, SERVO, HI CONTROL, AUDIO) PRINTED WIRING BOARD — Ref. No. VC-217 Board; 10,000 Series — VC-217 BOARD (SIDE B) C202 C-15...
DCR-TRV8/TRV8E/TRV10/TRV10E SECTION 5 ADJUSTMENTS Before starting adjustment EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
1-1. Adjusting items when replacing main parts and boards. • Adjusting items when replacing main parts When replacing main parts, adjust the items indicated by r in the following table. Replaced parts Block replacement Mounted parts replacement Adjustment Adjustment Section Initialization Initialization of C page data of B, C, D,...
Page 89
• Adjusting items when replacing a board or EEPROM When replacing a board or EEPROM, adjust the items indicated by r in the following table. Replaced parts Board replacement Adjustment Adjustment Section Initialization Initialization of C page data of B, C, D, Initialization of D page data E, F page Initialization of B page data...
5-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check Filter for color temperature correction (C14) J-6080-058-A White balance adjustment/check ND filter 1.0...
1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards Pattern Box need not be disassembled. Connect the equipment for adjustments according to Fig. 5-1-2. The front panel block (MA-358 board, focus ring, Audio/video jack, microphone unit) must be assembled because the focus ring and audio/video jack are used for adjustments.
Page 92
Cabinet (R) CN8607 CN8606 CN8603 CK-84 board CPC-8 jig CN8608 i J-6082-388-A j CN8605 AC power adaptor i 8.4Vdc) FP-82 AC-L10 or flexible AC-VQ800 Must be connected. Front panel block DC IN jack Must be connected Lens when performing CN2501 CN2907 block CN1810...
1-1-3. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. POWER switch (PS4550 block) ......CAMERA WHITE BALANCE (Menu display) ......AUTO NIGHT SHOT switch (Lens block) ......... OFF DISPLAY (Menu display) ......... V-OUT/LCD DEMO MODE (Menu display) ........
1-2. INITIALIZATION OF B, C, D, E, F PAGE DATA 3. C Page Table 1-2-1. INITIALIZATION OF C PAGE DATA Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the C Page 1. Initializing the C Page Data Data”.) Note: If the C page data has been initialized, the following adjustments Fixed data-2 : Modified data.
Page 95
Initial value Initial value Address Remark Address Remark NTSC PAL NTSC PAL Emergency memory address Fixed data-1 (Initialized data) Fixed data-1 (Initialized data) PLL f fine adj. Fixed data-2 Fixed data-1 (Modified data, copy the data built in (Initialized data) the same model.) Fixed data-1 (Initialized data)
1-2-2. INITIALIZATION OF D PAGE DATA 1. Initializing the D Page Data Initial value Address Remark Note: If the D page data has been initialized, the following adjustments NTSC PAL need to be performed again. Fixed data-1 1) Modification of D page data 2) Color viewfinder system adjustments 3) LCD system Adjustments Fixed data-2...
Page 97
*1: No mark: DCR-TRV10/TRV10E < >: DCR-TRV8/TRV8E 3. D Page Table Initial value Address Remark Note : Fixed data-1 : Initialized data. (Refer to “1. Initializing the D Page NTSC PAL Data”.) Fixed data-2 Fixed data-2 : Modified data. (Refer to “2. Modification of D Page Data”.)
*1: No mark: DCR-TRV10/TRV10E < >: DCR-TRV8/TRV8E 1-2-3. INITIALIZATION OF B PAGE DATA 1. Initializing the B Page Data Initial value Address Remark Note: If the B page data has been initialized, the following adjustments NTSC PAL need to be performed again.
Page 99
3. B Page Table Address Remark Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the B Page Fixed data-1 Data”.) (Initialized data) Fixed data-2 : Modified data. (Refer to “2. Modification of B Page Data”.) Fixed data-2 (Modified data, copy the data built in Address Remark the same model.)
1-2-4. INITIALIZATION OF E, F PAGE DATA Address Remark 1. Initializing the E, F Page Data Note: If the E, F page data has been initialized, following adjustments Fixed data-1 need to be performed again. (Initialized data) 1) Modification of E, F page data 2) Camera system adjustments Adjusting page Adjusting Address...
Page 101
3. F Page Table Initial value Address Remark Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the E, F NTSC PAL Page Data”.) Angular velocity sensor sensitivity Fixed data-2 : Modified data. (Refer to “2. Modification of E, F Page Data”.) adj.
Page 102
Initial value Initial value Address Remark Address Remark NTSC PAL NTSC PAL Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data)
Page 103
4. E Page Table Initial value Address Remark Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the E, F NTSC PAL Page Data”.) Fixed data-1 Fixed data-2 : Modified data. (Refer to “2. Modification of E, F Page Data”.) (Initialized data) Initial value Address...
Page 104
Initial value Address Remark NTSC PAL Fixed data-1 (Initialized data) AGC gain calibration adj. Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Table.
1-3. CAMERA SYSTEM ADJUSTMENTS 3. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain Before perform the camera system adjustments, check that the and offset. specified value of “VIDEO SYSTEM ADJUSTMENT” are satisfied. Subject Not required 1.
4. Flange Back Adjustment (Using Minipattern Box) The inner focus lens flange back adjustment is carried out Adjusting method: automatically. In whichever case, the focus will be deviated during 1) Install the minipattern box so that the distance between it and auto focusing/manual focusing.
5. Flange Back Adjustment (Using Flange Back Adjustment Chart and Subject More Than 500m Away) The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. 5-2. Flange Back Adjustment (2) 5-1.
6. Flange Back Check Subject Siemens star (2.0m from the front of the lens) (Luminance : approx. 200 lux) Measurement Point Check operation on TV monitor Measuring Instrument Specified Value Focused at the TELE end and WIDE end. Switch setting: 1) NIGHT SHOT ..............
7. Optical Axis Adjustment Align the lens Optical Axis with the that of the CCD imager. If deviated, center of picture can lose focus when zoom is operated from the WIDE end to the TELE end. Subject Siemens star Measurement Point Check on the monitor TV Measuring Instrument Adjustment Page...
8. Picture Frame Setting 9. AGC GAIN Calibration Adjustment Subject Color bar chart Subject Clear chart (Color reproduction adjustment (Color reproduction adjustment frame) frame) (1.5m from the front of the lens) Measurement Point Display data of page 1 (Note) Measurement Point Video output terminal Measuring Instrument Adjustment remote commander...
12. Auto White Balance & LV Standard Data Input 13. Auto White Balance Adjustment Adjust to the proper auto white balance output data. Subject Clear chart If it is not correct, auto white balance and color reproducibility will (Color reproduction adjustment be poor.
14. White Balance Check 15. Angular Velocity Sensor Sensitivity Adjustment • This adjustment is performed only when replacing the angular Subject Clear chart (Color reproduction velocity sensor. adjustment frame) Although this adjustment need not be performed when the circuit Filter Filter C14 for color temperature is damaged, etc., check the operations.
1-4. COLOR ELECTRONIC VIEWFINDER 1. VCO Adjustment (DD-123 board) Set the VCO free-run frequency. If deviated, the EVF screen will be SYSTEM ADJUSTMENT blurred. Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to Mode VTR stop avoid electrical shock.
2. Bright Adjustment (DD-123 board) 3. Contrast Adjustment (DD-123 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated value.
3) Press the PAUSE button of the adjustment remote commander. each time to set the data. 4) Select page: 0, address: 01, and set data: 00. Address DCR-TRV10 DCR-TRV8 Data DCR-TRV10E DCR-TRV8E 5) Check that the EVF screen is not colored. If colored, change the data of page: D, address: 71 and 72 so that the EVF screen is not colored.
1-5. LCD SYSTEM ADJUSTMENT 1. VCO Adjustment (PD-110 board) Set the VCO free-run frequency. If deviated, the LCD screen will Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to be blurred.
2. D range Adjustment (PD-110 board) 3. Bright Adjustment (PD-110 board) Set the D range of the RGB decoder used to drive the LCD to the Set the level of the VIDEO signal for driving the LCD to the specified specified value.
4. Contrast Adjustment (PD-110 board) 5. V-COM Level Adjustment (PD-110 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the common electrode drive signal level of LCD to the specified value. If deviated, the screen image will be blackish or saturated value.
8) Select page: 3, address: 22, set data: 00, and press the PAUSE button of the adjustment remote commander. DCR-TRV10 9) Select page: 3, address: 0C, set data: 00, and press the PAUSE DCR-TRV8 Data button of the adjustment remote commander. DCR-TRV10E 10) Select page: 0, address: 01, and set data: 00.
5-2. MECHANISM SECTION ADJUSTMENT On the mechanism section adjustment For details of mechanism section adjustments, checks, and replacement of mechanism parts, refer to the separate volume “DV MECHANICAL ADJUSTMENT MANUAL D Mechanism ”and “MECHANICAL ADJUSTMENT MANUAL D200 Mechanism ”. 2-1. HOW TO ENTER RECORD MODE WITHOUT 2-3.
5-3. VIDEO SECTION ADJUSTMENTS NTSC model : DCR-TRV8/TRV10 PAL model : DCR-TRV8E/TRV10E 3-1. PREPARATIONS BEFORE ADJUSTMENTS Use the following measuring instruments for video section adjustments. 3-1-1. Equipment Required 1) TV monitor 2) Oscilloscope (dual-phenomenon, band above 30 MHz with delay mode) (Unless specified otherwise, use a 10 : 1 probe.) 3) Frequency counter 4) Pattern generator with video output terminal.
3-1-2. Precautions on Adjusting Note 1: Setting the “Forced VTR Power ON” mode (VTR mode) 1) Select page: 0, address: 01, and set data: 01. The adjustments of this unit are performed in the VTR mode 2) Select page: D, address: 10, set data: 02, and press the PAUSE or camera mode.
3-1-3. Adjusting Connectors Some of the adjusting points of the video section are concentrated at VC-217 board CN2904. Connect the measuring instruments via the CPC-8 jig (J-6082-388-A). The following table lists the pin numbers and signal names of CN2904. CN2904 Pin No.
3-1-6. Alignment Tapes Use the alignment tapes shown in the following table. Use tapes specified in the signal column of each adjustment. Name Tracking standard (XH2-1) Tape path adjustment SW/OL standard (XH2-3) Switching position adjustment Audio operation check Audio system adjustment (XH5-3 (NTSC), XH5-3P (PAL)) System operation check Operation check...
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT 1. Initialization of B, C, D, E, F Page Data If the B, C, D, E, F page data is erased due to some reason, perform “1-2. INITIALIZATION OF B, C, D, E, F PAGE DATA”, of “5-1. CAMERA SECTION ADJUSTMENT”...
3-3. SERVO AND RF SYSTEM ADJUSTMENT 2. T reel FG Duty Adjustment (VC-217 board) Adjust the take-up reel FG signal duty cycle to an appropriate value Before perform the servo and RF system adjustments, check that so that the correct T-reel FG signal is obtained. the specified value of “36 MHz Origin Oscillation Adjustment”...
5-3. APC & AEQ Adjustment (VC-217 board) 6. PLL f & LPF f Final Adjustment (VC-217 board) Mode Playback Mode VTR stop Signal Recorded signal at “Preparations Signal Arbitrary before adjustments” Measurement Point Display data of page: 3, address: 03 Pin @º...
3-4. VIDEO SYSTEM ADJUSTMENTS 2. S VIDEO OUT Y Level Adjustment (VC-217 board) Before perform the video system adjustments, check that the specified value of “36 MHz Origin Oscillation Adjustment” of Mode Camera “CAMERA SYSTEM ADJUSTMENT” is satisfied. Subject Arbitrary Measurement Point Y signal terminal of S VIDEO jack 3-4-1.
3. S VIDEO OUT Chroma Level Adjustment 4. AV OUT Y, Chroma Level Check (VC-217 board) (VC-217 board) Mode Camera Mode Camera Subject Arbitrary Subject Arbitrary Measurement Point Chroma signal terminal of S VIDEO Measurement Point Video terminal of AUDIO/VIDEO jack (75 terminated) jack (75...
5. PLL Adjustment (VC-217 board) (Except AEP/UK model) Set the VCO center level of the video input circuit (IC1200). Mode VTR stop Signal Color bar (Video terminal of AUDIO/ VIDEO jack input) Measurement Point Display data of page: 3, address: 04 Measuring Instrument Adjustment remote commander Adjustment Page...
3-4-2. BIST Check 1. Playback System Check 1-1. Preparation for Playback Set the POWER switch to VTR (or PLAYER) position. When the playback system from IC1600(SFD) to IC2002 (ADC&DAC) is normal, the display data (combination data) Connect the adjusting remote commander and set the HOLD switch to ON (SERVICE) position.
• ENC Ca BIST(PB) Check 2. Recording System Check 35) Select page: 3, address: 10, set data: 8D, and press the PAUSE 2-1. Preparations for recording button. 36) Select page: 3, address: 12, set data: 10, and press the PAUSE Playback the BIST check tape.(XH5-6(NTSC), XH5-6P(PAL)) button.
2-5. IC1900(TRX) BIST(REC) Check 9) Select page: 3, address: 11, set data: 87, and press the PAUSE button. 1) Select page: 3, address: 12, set data: 04, and press the PAUSE 10) Select page: 3, address: 12, set data: 08, and press the PAUSE button.
3-5. IR TRANSMITTER ADJUSTMENTS 2. IR Video Deviation Adjustment (CK-84 board) Mode VTR stop Adjust using a IR receiver jig (J-6082-383-A). Signal Arbitrary Measurement Point VIDEO OUT terminal of IR receiver jig Switch setting: (Terminated at 75 ) LASER LINK ........ON (Red LED is lit) Measuring Instrument Oscilloscope 1.
3. IR Audio Deviation Adjustment (CK-84 board) Mode VTR stop Signal Video : No signal Audio : –400Hz, –7.5dBs, Audio left and right terminal of AUDIO/VIDEO jack Measurement Point AUDIO L terminal and AUDIO R terminal of IR receiver jig (Terminated at 47k ) Measuring Instrument Audio level meter...
3-6. AUDIO SYSTEM ADJUSTMENTS [Connection of Audio System Measuring Devices] Connect the audio system measuring devices as shown in Fig. 5-3-14. Main unit Recording (Camera mode) Left Audio oscillator Right Attenuator 600 : 270 (1-249-410-11) + 330 (1-249-411-11) Playback Main unit TV monitor Video (Yellow) Left (White)
1. Playback Level Check 4. Overall Noise Level Check Mode VTR playback Mode Camera recording and playback Signal Alignment tape: Signal No signal: Insert a shorting plug in the For audio operation check MIC jack (XH5-3 (NTSC)) Measurement Point Audio left or right terminal of AUDIO (XH5-3P (PAL)) VIDEO jack Measurement Point...
5-4. SERVICE MODE 4-1. ADJUSTMENT REMOTE COMMANDER 2. Precautions upon using the adjustment remote commander The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The Mishandling of the adjustment remote commander may erase the correct adjustment data at times.
4-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.
4-3. SERVICE MODE 2-1. EMG Code (Emergency Code) 1. Setting the Test Mode Codes corresponding to the errors which occur are written in Page D Address 10 addresses 38, 3C and 40. The type of error indicated by the code are shown in the following table.
2-2. MSW Code MSW when errors occur: Information on MSW (mode SW) when errors occur MSW when movement starts: Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved) MSW of target of movement: Information on target MSW of movement when the mechanism position is moved Mechanism Position UNLOAD...
3. Bit value discrimination Bit values must be discriminated using the display data of the adjustment remote commander for following items. Use the table below to discriminate if the bit value is “1” or “0”. Display on the adjustment remote commander Address Page bit3 to bit0 discrimination...
5. Switch check (2) Page 2 Address 60 to 67 Using method: 1) Select page: 2, address: 60 to 67. 2) By discriminating the display data, the pressed key can be discriminated. Data Address 00 (00 to 0A) 19 (0B to 24) 32 (25 to 44) 59 (45 to 6E) 85 (4F to 9F)
DCR-TRV8/TRV8E/TRV10/TRV10E SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • Model The components identified by mark ! or have some differences from the original one. DCR-TRV8 DCR-TRV10 dotted line with mark ! are critical for safety.
6-1-6. EVF AND LENS SECTION LCD903 not supplied IC001 not supplied M904 M905 Be sure to read “Precautions upon replacing CCD imager” on page 4-7 when changing the CCD imager. Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3949-615-2 CABINET (UPPER) ASSY, VF...
Page 153
6-1-7. CASSETTE COMPARTMENT AND DRUM ASSY SECTION FP-242 (See page 6-8) not supplied Attaching procedure not supplied Note M901 Note: Once remove No. 720 CC fastener, don't use it again. Be sure to replace it with new one. (Attaching procedure is as shown above figure.) Ref.
6-1-8. LS CHASSIS BLOCK SECTION Note 1: About FP-242 and FP-92 The FP-242 and FP-92 flexible boards are installed to a chassis with a hot press, which are included in the Ref. No. 762 chassis (D3) assy, LS block section, They are not supplied separately because the high precision for installation is needed. Note 2: Selecting the T washer Select proper parts for the Ref.
6-1-9. MECHANISM CHASSIS BLOCK SECTION-1 Note: Be sure to remember the installed position (one of two position), direction and thickness of the Ref. No. 820 (head spacer) when the M902 (capstan motor )is removed. Refer to “3-9. Capstan motor” on page 15 in the “DV MECHANICAL ADJUSTMENT MANUAL ”...
! are critical for safety. ordering these items. • Model Replace only with part number specified. • CAPACITORS: DCR-TRV8 Les composants identifiés par une marque uF: µF DCR-TRV8E ! sont critiques pour la sécurité. • COILS DCR-TRV10 Ne les remplacer que par une pièce portant...
Page 179
PARTS REFERENCE SHEET You can find the parts position of location of mount locations applying to VC-217 board of a set. VC-217 SIDE A DCR-TRV8/TRV8E/TRV10/TRV10E IC2503 IC2504 I C 1 8 1 6 IC2505 IC203 I C 1 9 0 0...
Page 180
OPTICAL AXIS FRAME Take a copy of OPTICAL AXIS FRAME with a clear sheet for use. — 264 —...
Page 181
FOR CAMERA COLOR REPRODUCTION ADJUSTMENT For NTSC model DCR-TRV8/TRV10 Take a copy of CAMERA COLOR REPRODUCTION FRAME and Parts referencesheets with a clear For PAL model sheet for use. DCR-TRV8E/TRV10E — 265 —...