Advertisement
INSTALLATION
Preparation
2
1
Remove the blue tape, air cushion and screw.
Remove the dome cover.
Do not touch the lens and lens barrel.
Push
1
Blue tape
A
Installing on the Ceiling
1
Connect the cables from the ceiling.
2
Mount the camera unit to the base plate.
2
1
Power
cables
Push the camera unit
until it clicks taking care
not to pinch the cable.
Supplied
screw
Make sure that the camera unit and base plate fit
perfectly.
3
5
Turn the lens
Loosen the
90 degrees
black
4
Screw
clockwise.
screw.
2
Air
cushion
B
Installing on the Wall
1
Set the lens in the correct direction.
1
A
Remove the black screw
.
2
Turn the lens in the arrow direction to reverse the
orientation.
3
Confirm that the dials are located at the top.
4
A
Temporarily tighten the removed black screw
.
2
3
14
A
Black screw
2
Connect the cables from the wall.
3
Mount the camera unit to the base plate.
2
Supplied
screw
Push the camera unit
until it clicks taking care
not to pinch the cable.
3
Make sure that the camera unit and base plate fit
perfectly.
ADJUSTING CAMERA IMAGE
b Checks on monitor
Connect a portable monitor.
MONITOR
OUT
GND
A dedicated MONITOR OUT connector is provided for
portable monitor.
b Angle-of-view adjustment
Adjust the angle of view by moving the lens unit.
200
(Ceiling Installed)
(Wall Installed)
● Do not touch the lens and lens barrel.
● When rotating the lens unit, make sure a metal
edge does not damage the cables.
b Zoom and focus
B
A
D C
1
2
Zoom
Focus
Loosen the zoom ring
Loosen the focus ring
A
C
knob
, and turn the
knob
, and turn the
B
D
zoom ring
to zoom in
focus ring
to focus on
or out.
the object.
When finished, tighten the zoom and focus ring
AC
knobs
securely.
When monitoring lighting or other extremely bright objects (which
exceed the maximum required illumination), smearing may occur in
the vertical or horizontal direction (either above and below the
high-brightness object or as a perpendicular band). In such a case,
adjust the angle of illumination and other factors while observing the
monitor.
Camera adjustments/settings
The camera comes pre-adjusted and ready to install at the
time of factory shipment, but you can make adjustments or
settings if you need.
If you have trouble adjusting the camera, consult your dealer
or an Authorized Sanyo Service Center.
● Electronic shutter speed setting
● White balance (color compensation)
(unit: second)
Manual White Balance
1/50
1/120
1/1000
1/2000
1
2
1
2
1
2
1
2
6
Switch1: MSB Switch2: LSB
• Using the high speed electronic shutter indoors
with low lighting, will give darker pictures. In
such a case, add some lights to make sure the
● Sync setting
lighting is sufficient.
• If the lighting is very bright, pay attention to the
Line-Lock
light angle in order to avoid or minimize the
smear phenomenon effect.
Synchronizes the unit with
power frequency*
● Aperture compensation
Sharp outline
Normal outline
7
3
3
* Adjust the roll by turning the LINE PHASE dial on the
● Backlight compensation
second and subsequent cameras.
If the vertical roll cannot be corrected by adjusting
the LINE PHASE dial on the second and
subsequent cameras, try adjusting the LINE
PHASE dial on the first camera. If it still cannot be
corrected, please check that the polarity of the
Only when using an auto-iris lens
power cords of all connected devices is correct.
● Lens iris level adjustment
Multi-spot metering
High
Normal
Backlight compensation
If the entire image is too dark or too bright, adjust
to the entire screen*
the condition.
4
5
4
5
Center zone metering
Low (darker)
Backlight compensation
to the central portion of
4
5
the screen
OFF
4
5
* If the background of the object is extremely dark, set to
Center zone metering.
After finishing camera adjustments/settings ...
1
2
Tighten the screw.
Install the dome cover.
1
Push the dome cover until it clicks.
For wall installation, securely tighten the
screw you temporarily tightened.
2
While holding down the dome cover, turn it
in the direction of the arrow until the lens is
completely visible through the camera
window.
Français
Deutsch
English
Auto-Tracing
White balance
MWB
6
RED
BLUE
Turn clockwise to
augment the color.
Internal sync
LL
7
PHASE
A. I. LENS
High (brighter)
LEVEL
1
1
2
Advertisement
