Related Manuals for Miele T 8023 C
Summary of Contents for Miele T 8023 C
- Page 1 Operating and Installation Instructions Condenser Dryer T 8023 C en - US, CA To prevent accidents and appliance damage read these instructions before installation or use. M.-Nr. 09 460 400...
-
Page 2: Table Of Contents
Contents IMPORTANT SAFETY INSTRUCTIONS....... . . 3 Control panel ........... . . 5 Before loading the dryer . -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS To prevent the risk of fire, the WARNING - To reduce the risk of following textiles must not be dried in fire, electric shock, or injury to this dryer: persons when using your appliance, – items which have not been washed. follow basic precautions, including the following: –... -
Page 4: Save These Instructions
IMPORTANT SAFETY INSTRUCTIONS Allow the dryer to complete each GROUNDING INSTRUCTIONS stage of the program selected, This appliance must be grounded. In including the cooling down phase. This the event of malfunction or breakdown, will ensure that the items being grounding will reduce the risk of removed are not too hot to handle electric shock by providing a path of... -
Page 5: Control Panel
Control panel e- "Programs" buttons "Start/Stop" button For selecting a drying program. Starts and stops a program. Interrupts a program when pressed. "Options" buttons Flashes during program selection For selecting a drying option. and lights once the program starts. "Dryness" button "Door"... -
Page 6: Before Loading The Dryer
Before loading the dryer Program recommendations The dryer must be correctly installed Normal and connected before the first use. Please refer to the "Installation – Cottons and Permanent Press blends Instructions". Wrinkle-free ^ Before using for the first time, clean the drum with a cloth. -
Page 7: Using The Dryer
Using the dryer 1. Turn on the dryer and load 2. Select a program the laundry ^ Press the "On/Off" button to turn on the dryer. ^ Press the "Door" button to open the door. ^ Load the laundry loosely into the drum. - Page 8 Using the dryer Program Fabric Note Normal Available drying options: Turbo, Gentle, Anti-crease Extra Dry Multi-layer fabrics, mixed loads of The "Extra dry" program should not be sturdy cottons, e.g. jeans, towels. selected for jersey materials. Items may shrink. More Dry Uniform loads of cotton, e.g.
-
Page 9: Select A Drying Option (If Needed)
Using the dryer 3. Select a drying option OPTIONS (if needed) Turbo Fast drying for sturdy fabrics with increased temperature and a reduced program length. Gentle For drying delicate fabrics slowly at a lower temperature. Anti-crease Prevents wrinkles if laundry is not removed immediately after the end of a program. -
Page 10: Select The Dryness Level
Using the dryer 4. Select the dryness level 5. Select the buzzer (if desired) ^ Press the "Buzzer" button to have a The dryness level can be selected in the "Normal" and "Wrinkle-free" tone beep at the end of the program. programs. -
Page 11: Start The Program
Using the dryer 6. Start the program 7. At the end of a program The "End/Anti-crease" indicator will light at the end of a program and the buzzer will sound if it was selected. If a fault occurred, a "FAULT" indicator ^ Press the "Start/Stop"... -
Page 12: Canceling Or Changing A Program
Using the dryer Canceling or changing a Adding or removing laundry program during a program ^ Press and release the "Start/Stop" ^ Turn off the dryer using the "On/Off" button to stop the drying program. button. ^ Press the "Door" button. To continue drying: ^ Select the new program by pressing ^ Open the door. -
Page 13: Child Lock
Child lock Child lock To deactivate the child lock Repeat steps 1. to 5. When activated, the child lock prevents the dryer from being operated by The "Child lock" indicator will go out. locking the control panel functions. The control panel is now unlocked. The dryer can be turned on but not 6. -
Page 14: Dryer Care
Dryer care Cleaning the lint filter The lint filter must be cleaned after every program. ^ Remove the lint from the door frame lint filter with your fingers. ^ Any lint remaining in the hollow casing of the door can be removed through the gap at the bottom with a ^ Open the door and remove the lint dust brush or vacuum. -
Page 15: Cleaning The Exterior And The Control Panel
Dryer care Cleaning the exterior and the control panel The lint filters can be rinsed with hot water if necessary. To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. -
Page 16: Emptying The Condensed Water Container
Dryer care Emptying the condensed water container Depending on the installation, the condensed water will either be pumped to a drain or collected in the condensed water container, located in the upper left corner of the machine. The container holds approximately 1 gallon of water. -
Page 17: Cleaning The Condenser
Dryer care Cleaning the condenser To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. ^ Clean the condenser every 6 months and when the "Filter/Vent"... - Page 18 Dryer care Rinsing the condenser Returning the Condenser ^ Put the condenser back in place in the reverse order. Check that the gasket around the front of the condenser is flush and not crimped. ^ To prevent leaks, make certain the condenser is pushed in all the way and locked in place.
-
Page 19: Quick Guide
Quick Guide Remove this guide for easy reference Please read all instructions, especially the "Important Safety Instructions", before using the dryer. - Page 20 Quick Guide 1.Turn on the dryer and load the 2. Select a program laundry ^ Press the "On/Off" button to turn on the dryer. ^ Press the "Door" button to open the door. ^ Load the laundry into the drum. Make ^ Press the e or - button until the sure that there is enough space in desired program indicator lights.
- Page 21 Quick Guide 4. Select the dryness level 5. Select the buzzer (if desired) 6. Start the program ^ Press the "Start/Stop" button. 7. At the end of a program The "Anti-crease / End" indicator will light. ^ Press "Door" and remove the laundry. ^ Clean the lint filter.
- Page 22 Quick Guide Program When to use Note Normal Available drying options Turbo, Gentle, Anti-crease Extra Dry For laundry to be folded and shelved The "Extra Dry" program should not be immediately, e.g. jeans, towels. selected for jersey materials. Items may shrink. More Dry For uniform loads, e.g.
-
Page 23: Dryer Care
Changing the light bulb ^ Replace the light bulb with a temperature proof bulb, available To reduce the risk of electric from Miele. shock, disconnect the dryer from the power supply by shutting off the The light bulb must not exceed the... -
Page 24: Frequently Asked Questions
Frequently asked questions What if the dryer will not run? Possible fault Solution The "Start/Stop" button was not Make sure the dryer is on. Press the pressed. "Start/ Stop" button to begin the drying program. The circuit breaker tripped or the dryer Make sure the dryer is plugged in or is unplugged. - Page 25 Frequently asked questions What if the "Filter/Vent" fault indicator is lit? Possible fault Solution The lint filter is clogged. Clean the lint filters. See "Dryer care". The air supply in the room is Open a window or door to increase insufficient.
-
Page 26: After Sales Service
Miele Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further... -
Page 27: Installation Instructions
Installation Instructions To prevent accidents and machine damage read these instructions before installation or use. -
Page 28: Important Safety Instructions
If it will not fit the outlet, have a proper outlet installed by Repair and maintenance work a qualified electrician. should be performed by a Miele authorized service technician. Work by Do not use an extension cord to unqualified persons could be connect this appliance to the power dangerous and could void the warranty. -
Page 29: Washer / Dryer Stack
Washer / Dryer Stack The tumble dryer can also be placed on top of a Miele washing machine for a stacked installation. An appropriate stacking kit is required. The stacking kit is available from your Miele dealer or the Miele Technical Service Department. -
Page 30: Electrical Connection
Electrical connection The dryer comes with a 5 ft long, GROUNDING INSTRUCTIONS 12/4 AWG cord and a NEMA 14-30 P This appliance must be grounded. plug. In the event of malfunction or It should be connected to a breakdown, grounding will reduce 120/208-240 V, 30 A, 60 Hz AC power the risk of electric shock by supply. -
Page 31: Installation
Installation Front view Power cord with plug Four height adjustable feet Condensed water container Optional drain hose: An alternative to using the Control panel condensed water container is to Door drain condensed water into a sink, standpipe or gully. Access panel to condenser... -
Page 32: Installation Site
Installation Rear view Installation site Do not install the dryer in an area where it can be blocked, e.g. behind a door. This appliance is not intended to be mounted in a wall or other vertical surface of a building or cabinet. -
Page 33: Installation Beneath A Counter
It must be installed by a Miele Service Technician. The cover plate of the built-under kit replaces the appliance lid and ensures electrical safety. -
Page 34: Installation Tips
Installation Installation tips Level the dryer An airflow gap of " (10 mm) must be provided between the machine and the floor. This airflow gap must not be blocked by a toe-kick or thick piled carpets. Sufficient venting of the installation site, e.g. -
Page 35: External Water Drain
If the hose is not long enough, an extension hose is available as an ^ Unwind the hose from the holder and optional accessory from the Miele. carefully pull it from the clamps. Installing the drain hose Do not pull or kink the drain hose, it... - Page 36 Installation Draining the condensed water into a sink ^ Secure the hose carefully, e.g. by tying the hose to the water tap, to avoid damage by overflowing water. ^ Use the curved guide to prevent the drain hose from becoming kinked (see Front view illustration).
-
Page 37: Installation Requirements
Installation Installation requirements Example: Connection to a sink standpipe demanding a non-return valve Connect the drain hose with a To prevent water from flowing non-return valve directly to a sink back into the machine a non-return standpipe. valve must be installed at the following installations: –... - Page 38 Installation ^ Install the connector 1 with the sink connecting nut 2 to the sink standpipe. Usually the sink connection nut is equipped with a washer. Please remove the washer. ^ Plug the hose end 4 to the connector ^ Using a screwdriver tighten the hose clamp 3 directly behind the sink connecting nut.
-
Page 39: Caring For The Environment
Caring for the environment Disposal of the packing Disposal of an appliance materials Old appliances may contain materials that can be recycled. Please contact The packing materials protect the your local recycling authority about the appliance during shipping. They have possibility of recycling these materials. - Page 40 All rights reserved / 2812 M.-Nr. 09 460 400 / 00 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.