Sharp PN-V600A Operation Manual page 29

nZOOM2 SPECIAL SETTING
If you connect a laptop computer with any of the following
screen resolutions and black bands appear around the
screen, set ZOOM2 SPECIAL SETTING of INPUT SIGNAL on
the OPTION menu to ON and then select ZOOM2 in the SIZE
setting.
This displays the area inside the black band.
Laptop computer
Corresponding signal*
resolution
1280x800 1280x1024, 1280x960, 1400x1050*
1280x600 1280x720
1024x600 1024x768
*1: T his setting is effective only when the screen resolution,
including the black band, is one of the resolutions listed
above.
*2: U se the automatic screen adjustment.
nSCHEDULE
You can set the time to switch the monitor on and off.
Set this function with "SCHEDULE" in the OPTION menu. (See
page 26.)
When BRIGHT is set, set BRIGHTNESS SENSOR to OFF on
the SETUP menu.
SCHEDULE
– –/– –/– – – –
(2) (3)
(1)
No. POWER DAY OF THE WEEK
– – – – – – – –
-
– – – – – – – –
-
– – – – – – – –
-
– – – – – – – –
-
– – – – – – – –
-
– – – – – – – –
-
– – – – – – – –
-
– – – – – – – –
-
1 3 6 6 x 7 6 8
V: 60 Hz
1. Press or to select the SCHEDULE number, and
press .
2. Set the SCHEDULE. (See the description below.)
Press or to select items, and press
change the setting.
MENU
3. Press .
SCHEDULE becomes effective.
(1)
●: SCHEDULE effective
-: SCHEDULE not effective
(2) POWER
ON : Switches the monitor on at the specified time.
OFF : Switches the monitor off at the specified time and puts
the monitor in standby mode.
1
PC D-SUB
– – – – –:– –:– – – –
(4) (5) (6)
TIME INPUT BRIGHT
– – – – – – – – – –
:
– – – – – – – – – –
:
– – – – – – – – – –
:
– – – – – – – – – –
:
– – – – – – – – – –
:
– – – – – – – – – –
:
– – – – – – – – – –
:
– – – – – – – – – –
:
OK···[MENU]
H: 47.7 kHz
or
(3) DAY OF THE WEEK
Specifies the day of the week to execute the SCHEDULE.
0: ONLY ONCE
Executes the SCHEDULE once on the specified day.
Specify the day of the week to execute the SCHEDULE.
1: EVERY WEEK
Executes the SCHEDULE on the specified day of the week
every week. Specify the day of the week to execute the
SCHEDULE.
Periodic setting such as "Monday through Friday" is also
2
possible.
2: EVERY DAY
Executes the SCHEDULE every day regardless of the day
of the week.
(4) TIME
Specifies the time to execute the SCHEDULE.
Set the time on a 12-hour basis. (Factory default)
Can be entered as 24-hour time using the TIME setting in
DATE/TIME FORMAT.
(5) INPUT
Specifies the input mode at power-on. When not specifying,
the screen at the previous power-off appears.
Input modes displayed on DVI, HDMI and BNC depend on
INPUT SELECT settings.
(6) BRIGHT
Sets the brightness when changing the screen brightness at
a specified time.
Caution
• Do not switch off the main power after setting the
SCHEDULE.
• Specify the correct date and time. (See page 26.)
SCHEDULE does not function unless the date and time are
specified.
• Check regularly that the set date and time are correct.
• When STANDBY MODE is LOW POWER, SCHEDULE
cannot be set.
• When a temperature abnormality occurs and the backlight
brightness is reduced, the brightness is not changed even
if a schedule set to BRIGHT is executed.
TIPS
to
• Up to 8 SCHEDULE items can be registered.
• Setting the SCHEDULE flashes the power LED alternately
in red and orange in standby mode.
• A SCHEDULE that has a large number has precedence
over that of a small number when schedules overlap.
Menu Items
29
E