Dimensions; Terminal Layouts And Wiring Diagrams - Panasonic LT4H/-L Manual

Dimensions

• LT4H digital timer
48
1.890
TIMER
OP.
RST
LOCK h m s
UP
RESET
LOCK
LT4H
DOWN
• Dimensions for embedded installation (with adapter installed)
Screw terminal type
Rubber gasket
ATC18002 (supplied)
TIMER
OP.
48 50
RST
1.890 1.969
LOCK h m s
UP
RESET
LOCK
LT4H DOWN
48
1.890 .039
• Dimensions for front panel installations
DIN rail terminal block
(8-pin type AT8-DF8K
sold separately)
(11-pin type AT8-DF11K
sold separately)
Device installation rail
AT8-DLA1
(sold separately)
95.5
(90.0)
3.760
( ) dimension is for 8-pin type.
(3.543)

Terminal layouts and Wiring diagrams

• 8-pin type
Relay output type
N.C.
Start
5
4
Reset
6
3
7
2
1 8
Operating
–
+
voltage
• Screw terminal type
Relay output type
Reset
Start
Stop
Lock
6 7 8 9 10
N.C.
1 2 3 4 5
Operating
+ –
voltage
Screw terminal type
(Flush mount)
5.5
.217
7.5
.295
Panel
Mounting frame
for flush mount
AT8-DA4 (supplied)
66
2.598
1 63.5
2.500
• Installation panel cut-out dimensions
The standard panel cut-out dimensions are shown
below. Use the mounting frame (AT8-DA4) and rub-
ber gasket (ATC18002).
80 min.
3.150
Transistor output type
Start
N.O.
5
4
Reset
3
2
1 8
Operating
–
voltage
Transistor output type
Reset
Start
Stop
Lock
N.O.
6 7 8 9 10
1 2 3 4 5
Operating
+ –
voltage
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
64.5
2.539
44.5
1.752
Pin type
Rubber gasket
ATC18002 (supplied)
TIMER
OP.
44.5 48
RST
1.752 1.890
LOCK h m s
UP
RESET
LOCK
LT4H DOWN
48
1.890
80 min.
3.150
45 +0.6 1.772 +.024
0 0
+0.6
45
0
1.772 +.024
0
• 11-pin type
Relay output type
Reset
Start
Stop
Lock
6
4
3
7
2
+
–
Note) For connecting the output leads of the transistor output type, refer to
5) Transistor output on page 48.
Pin type
(Flush mount/Surface mount)
5.5 55.6
.217 2.189
7.5
.295
Panel
Mounting frame
for flush mount
AT8-DA4 (supplied)
50 66
1.969 2.598
1
.039 3.543
• For connected installations
45 +0.6
0
1.772 +.024
0
A = (48 × n – 2.5)
Note) 1: The installation panel thickness should be between 1
and 5 mm .039 and .197
Note) 2: For connected installations, the waterproofing ability
between the unit and installation panel is lost.
Transistor output type
Reset
N.C.
6
N.O.
5 7
8
9
10
1 11
Operating
+
voltage
LT4H/-L
(units: mm inch)
Tolerance: ±1.0 ±.039
14.5
.571
44.5
1.752
8-pin type
(8p cap AD8-RC
sold separately)
11-pin type
(11p cap AT8-DP11
sold separately)
90
A
+0.6
0
inch.
Start
Stop
6
5 7
Lock
4 8
3 9
2 10
1 11
Operating
– +
voltage