Table of Contents
Advertisement
INSTALLING THE RANGE HOOD
.,G. lo
16.Bring
electrical
cable through
access
hole drilled in wall or
bottom
of cabinet.
Provide
6" wire leads and install
proper
connector
for type
of cable
being
used.
Remove
lock
nut
from connector
and let prepared
cable project
through
cabi-
net or wall opening
so it is ready
for installation
into range
hood. (FIG. 10)
17.Position
hood in place so that:
a)
Electrical
line is routed through
appropriate
knockout
open-
ing. This step will have to be accomplished
while position-
ing hood. (FIG. 13)
b)
Large
part
of keyhole
mounting
slots
on hood
fit onto
hood
mounting
screws
projecting
from
bottom
of cabi-
net. (FIG. 11 )
c)
Damper/duct
connector
slides
into duct work
in wall or
cabinet.
18. Adjust hood so the front of hood is flush with cabinet
front.
19.Tighten
the four hood
mounting
screws
securely.
20.Install
Iocknut
on electrical
connector
and tighten
securely.
21 .Make electrical
connection
using wire nuts to connect
white
wire to white,
black wire to black.
Ground
hood
to prepared
hole using green
ground
screw
provided.
(FIG.
12)
22.Replace
wiring
box cover
and screw.
Make sure that all wir
ing is safely
contained
inside.
NOTE
I
or Ductfree
Installations
Only:
I
install
both
filters.
Make
sure
that ductfree
filter
(purchase
separately)
is next to fan assembly
with blue side next to blade.
Aluminum
filter
should
be facing
out.
USE AND CARE
SWITCHES
Right knob controls
light.
Left knob
controls
blower.
Rotate
knob
CLOCKWISE
to turn
blower
ON to HIGH
speed.
Further
CLOCKWISE
rotation
de-
creases
blower
speed.
Rotate
knob
fully
COUNTERCLOCK-
WISE
(past
HIGH
speed)
to turn fan OFF.
CLEANING
Finish
Keep your
range hood clean using a mild detergent
suit-
able for painted
surfaces.
Aluminum
Filters
should
be cleaned
frequently
with
a deter-
gent solution
to avoid grease
build up. They are also dishwasher
safe.
FILTER
REMOVAL
Filters
are removed
by turning
filter
clip to the side and lifting
filter
or filters
out. In ducted
version,
turn filter
retaining
clip to
one side and place
aluminum
filter
under
embossed
retaining
tabs on back of fan housing.
Turn filter clip so that the low end of
clip holds single
filter firmly
in place.
(FIG.
13)
In ductfree
version,
place both aluminum
and ductfree
filter un-
der tabs on back of fan housing.
Turn filter retaining
clip so that
high
end holds
both
filters
firmly
in place.
Make
sure
ductfree
filter
is next to fan assembly,
with
blue side next to fan blade,
and aluminum
filter is facing
out.
NOTE:
Make
sure
that arrows
on filter
retaining
clip point
to-
ward
back and front of hood.
LIGHT
BULB
REPLACEMENT
Light
bulb (not supplied
with
hood)
should
be 75 watts
maxi-
mum.
The lens covering
bulb is removed
by pressing
the two
extending
tabs together
until they release
from the retaining
slots. (FIG.
14)
FAN ASSEMBLY
REMOVAL
Be sure power
is disconnected.
Remove
filters.
Remove
the two
screws
holding
the motor bracket
to the range hood and unplug
the fan assembly.
Be careful
not to allow fan assembly
to drop
when the screws
are removed.
(FIG.
15).
FIG. 11
FIG. 12
FIG. 13
FIG. 14
FIG. 15
CONNECTOR
_
!
AL LINE
BLACK
W,RES
,,TEW,RES
(BARE OR
STARLOCKNUT
GROUNDING]
GREEN WIRE)
BRACKET
CLIP
NON-DUCTED
FILTER
(SOLD SEPARATELY)
ALUMINUM
FILTER
Advertisement
Table of Contents
