Page 1
LC-40LE822E LC-40LE812E LC-40LE822ERU LC-40LE812ERU LC-40LU822E LC-40LX812E LC-46LE822E LC-40LX812ERU LC-46LE822ERU LC-46LE812E LC-46LU822E LC-46LE812ERU LC-52LE822E LC-46LX812E LC-52LE822ERU LC-46LX812ERU LCD COLOUR TELEVISION LCD-FARBFERNSEHGERÄT TÉLÉVISEUR COULEUR À ÉCRAN CRISTAUX LIQUIDES (LCD) TELEVISORE A COLORI LCD LCD-KLEURENTELEVISIE TELEVISIÓN EN COLOR LCD TELEVISOR DE CRISTAL LÍQUIDO OPERATION MANUAL LCD RENKLİ...
Page 2
SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked and of the same rating as above, which is also indicated on the pin face of the plug, must be used.
Dear SHARP customer Attaching the stand unit ........7 Using the remote control unit ........ 8 Thank you for your purchase of the SHARP LCD colour Quick guide ..............9 TV product. To ensure safety and many years of trouble- Initial installation overview........
Introduction Important safety precautions • Cleaning—Unplug the AC cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product. Do not use liquid cleaners or aerosol cleaners. • Use a soft damp cloth to gently wipe the panel when it is dirty. To protect the panel, do not use a chemical cloth to clean it. Chemicals may cause damage or cracks in the cabinet of the TV.
Introduction Part name Remote control unit >a (Standby/On) > LE822E/LE822ERU/LU822E (Page 16) Exit the “Menu” screen. p (Display information) Press to access conventional Press to display the station analogue TV mode. information (channel number, signal, etc.) in the upper right corner of the screen (Page 41).
Refer to the guide display below the menu Contrast bar to see when to press the ; button. This product is embedded with LC Font technology, which was developed by SHARP Corporation for clearly displaying easy-to-read LCFONT characters on LCD screens.
Introduction Operation without a remote control unit This function is useful when there is no remote control unit within your reach. Press @- and the “Menu” screen displays. Press !s/r instead of a/b or Yl/k instead of c/d to select the item.
Preparation Attaching the stand unit • Before performing work, spread cushioning over the surface on which you will be laying the TV. This will prevent it from being damaged. CAUTION • Attach the stand in the correct direction. • Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over. Confirm that there are nine screws (four long Insert and tighten four short screws into the screws and five short screws) with the stand...
Preparation Using the remote control unit Inserting the batteries Before using the TV for the first time, insert two supplied “AAA” size alkaline batteries. When the batteries become depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries. Open the battery cover.
Quick guide Initial installation overview Follow the steps below one by one when using the TV for the first time. Some steps may not be necessary depending on your TV installation and connection. Run the Preparation initial Watch TV settings ...
Quick guide Before turning on the power Standard DIN45325 plug (IEC 169-2) 75 q coaxial cable Place the TV close to the AC outlet, and keep the power plug within Satellite antenna cable reach. AC cord (product shape varies in some countries) ...
Quick guide Starting channel search. Initial auto installation When the TV is powered on for the first time after Digital search purchase, the initial auto installation wizard appears. Analogue search Follow the menus and make the necessary settings one after another. Skip Confirm the following before turning on Press a/b to select “Digital search”, “Analogue...
Page 14
Quick guide Searching for cable broadcasts Menu Description Selectable items Specifies if you To change each item to the appropriate Scrambled need to add pay-TV Yes, No settings: stations services. Press a/b to select the menu, and then press ;. Channel: Extracts all of information from a channel (quick, but...
Page 15
Quick guide Start search: Searching for satellite broadcasts DVB-S/S2 channel searching. Press c/d to select “Yes”, and then press Press c/d to select “Start search”, and then press ;. The TV searches for, sorts and stores all the receivable TV stations according to their settings and the connected antenna.
Quick guide Press a/b to select “Next”, and then press When you change the antenna connection setting: Press c/d to select “Change setting” on the SAT1 [ASTRA 1] DVB-S/S2 setting screen in the left column, and then press ;. Next •...
Quick guide Channel strength of DVB-T Checking signal strength and Supply voltage channel strength (DVB-T/C/S/S2) Frequency Signal strength Channel strength If you install a DVB-T/C/S/S2 antenna for the first time CH No. or relocate it, you should adjust the alignment of the Signal strength antenna to receive a good reception while checking the Current...
Watching TV Daily operation Switching between digital, satellite and analogue broadcasts Switching on/off Watching digital Watching analogue broadcasts broadcasts Turning on/off the power Turn on (;) the MAIN POWER switch on the rear of the TV (Page 4). Watching satellite To turn on the TV, press <a on the TV broadcasts or >a on the remote control unit.
Watching TV Selecting an external video Selecting a sound mode source DTV/SAT mode Once the connection If multi sound modes are received, each time you press CH list is made, press b to 7 the mode switches as follows. display the “INPUT” screen, and then press b or Audio (ENG) STEREO...
Watching TV EPG is a programme list that is displayed on the screen. With the EPG, you can check the schedule of DTV/SAT/RADIO/ DATA, view detailed information about them, tune to an event currently on-air. Useful settings for using EPG Basic setting EPG display settings View setting...
Watching TV Selecting a programme using EPG Basic operation The illustrations on this page are explained using three digit services. Display/Close the EPG screen Press EPG. Programme info. Search by genre Search by date Timer list Select Enter Back Exit NOTE •...
Page 22
Watching TV Display the timer list for TV Cancelling the timer setup programmes Press EPG. Press B. • Refer to page 20 for the timer setup. Press a/b/c/d to select the programme with timer setup, and then press ;. Timer setup using EPG Press c/d to select “Cancel”, and then press You can switch to a programme at a set time.
Watching TV Buttons for teletext operations Teletext Buttons Description What is teletext? :r/s Increase or decrease the page number. Teletext broadcasts pages of information and Select a group or block of pages displayed entertainment to specially equipped TV. Your TV receives in the coloured brackets at the bottom of Colour (R/G/Y/B) teletext signals broadcast by a TV network, and decodes...
Connecting external devices Before connecting ... • Be sure to turn off the TV and any devices before making any connections. • Firmly connect a cable to a terminal or terminals. • Carefully read the operation manual of each external device for possible connection types. This also helps you get the best possible audiovisual quality to maximise the potential of the TV and the connected device.
Connecting external devices SCART connection Component connection Example of connectable devices Example of connectable devices DVD player/recorder DVD player/recorder You will enjoy accurate colour reproduction and high quality images through the EXT 3 terminal when connecting a DVD player/recorder or other device. Decoder ...
Connecting external devices Audio connections VIDEO connection Speaker/amplifier connection Example of connectable devices Connect an amplifier with external speakers as shown DVD player/recorder below. Game console Camcorder Connecting an amplifier with digital/ analogue audio inputs You can use the EXT 2 terminal when connecting to a game console, camcorder, a DVD player/recorder or other device.
AQUOS LINK Controlling HDMI devices using AQUOS LINK What is AQUOS LINK? Using the HDMI CEC protocol, with AQUOS LINK you can interactively operate compatible system devices (AV amplifier, DVD player/recorder, Blu-ray player/ recorder) using a single remote control unit. NOTE •...
AQUOS LINK Connecting an AQUOS BD player/AQUOS recorder via Connecting an AQUOS BD the AQUOS AUDIO speaker system player/AQUOS recorder only AQUOS BD player/AQUOS recorder AQUOS BD player/AQUOS AQUOS AUDIO speaker system recorder The ARC (Audio Return Channel) function ...
AQUOS LINK Operating an AQUOS LINK device Setup menu AQUOS LINK allows you to operate the HDMI-connected You can call up the menu of an HDMI CEC-compatible device with a single remote control unit. external device (player, recorder, decoder, etc.) using the “Setup menu”...
Basic adjustment NOTE Picture settings You can also select “AV mode” by pressing #. • • The item marked with * is available only when selecting “HDMI 1”, “HDMI 2”, “HDMI 3”, “HDMI 4” or “EXT 3” from the “INPUT” Go to “Menu”...
Page 31
Basic adjustment Picture Film mode Advanced Automatically detects a film-based source (originally encoded at 24 or 25 frames per second, depending on This TV provides various advanced functions for the vertical frequency), analyses it and then recreates optimising the picture quality. each still film frame for high-definition picture quality (“Advanced (High)”, “Advanced (Low)”, “Standard”, “Off”).
Basic adjustment Audio settings Audio Bass enhancer Go to “Menu” > “Setup” > “Audio”. This function allows you to enjoy bass-enhanced sound. Menu CH list Setup Audio :Enter :Back Clear voice Audio This function emphasises speech against background STANDARD noise for greater clarity. Auto volume [Off] Setting audio input...
Basic adjustment “Energy save” status icons Power save settings Icon Description Go to “Menu” > “Setup” > “ECO”. “Energy save” is set to “Standard”. Menu “Energy save” is set to “Advanced”. CH list Setup :Enter :Back When “Energy save” is set to “Standard” or “Advanced”, “Energy save”...
Basic adjustment Digital search Channel settings After selecting the service you want to search, either “Terrestrial” or “Cable”, refer to Digital Menu broadcast setting on pages 11_12. CH list Setup Analogue search :Enter :Back The TV searches for, sorts and stores all the receivable TV stations.
Basic adjustment Manual adjust Manual search Configure various settings for each service using the Add new services within a specified frequency band. colour (R/G/Y/B) buttons. After setting the items on the following screen, the TV starts searching. • Refer to the table about menu items in the right column Service Service Lock...
Basic adjustment Analogue setting Skip You can reconfigure the analogue TV channels settings Channels with “Skip” set to “On” are passed over when automatically or manually. using :r/s even if selected while watching the image from the TV. Additional search Use this menu to add new services automatically after Decoder “Analogue search”...
Basic adjustment View setting Password/Lock settings Parental rating View setting This function allows DTV services to be restricted. It prevents children from watching violent or sexual scenes that may be harmful. Allows you to use a PIN to protect certain settings from Go to “Menu”...
Basic adjustment View setting Language settings Language View setting You can select an OSD language from among 23 Digital audio language languages. Refer to the OSD language column in the specification table for the selectable languages (Page 56). Set up to three preferred multi audio languages to display Go to “Menu”...
Useful viewing functions • Time shift does not work for ATV, external inputs, data Time shift broadcasts and radio broadcasts. • To release time shift, press READY, change the DTV/SAT channel, change “INPUT” or turn off the power of the TV. This function enables you to pause the digital TV or •...
Page 40
Useful viewing functions Option Display information regarding time shift Auto input selection Channel display Channel information displays by pressing p on the remote You can choose whether or not to switch the input control unit. source automatically when receiving an AQUOS LINK or an Euro SCART compatible signal on the TV during time shift operations.
Useful viewing functions Item (for SD [Standard-Definition] signals) Selecting the picture size Keeps the original aspect ratio in a full Normal screen display. Selecting the WSS picture size For 14:9 letterbox pictures. A thin side bar appears on each side, and you may automatically Zoom 14:9 also see bars on the top and bottom...
Useful viewing functions Selecting the recording picture Adjusting image position size manually Option Option Position REC picture size For adjusting a picture’s horizontal and vertical position. You can use this menu to set the appropriate picture size Go to “Menu” > “Setup” > “Option” > “Screen for viewing a 16:9 format TV programme on a 4:3 TV.
Useful viewing functions Display settings Time and title display Channel display View setting Time display You can display the channel information by pressing p on the remote control unit. Go to “Menu” > “Setup” > “View setting” > DTV mode ATV mode “Individual setting”...
Other useful features Repeat until the label is fully spelt out. Setting when using external NOTE devices • The label can be six characters or less. • When you want to set an input source label of less than six characters, select “END”...
Other useful features Additional features Option Channel selecting effect Option This function shows a screen effect when choosing or Colour system changing channels. Go to “Menu” > “Setup” > “Option” > “Screen You can change the colour system to one that is effect”...
Other useful features NOTE Connecting a USB device • You may need to setup the TV for a Home network server in “Ethernet setup” from the “View setting” menu. Connect a USB device to the TV as shown below. • The factory preset value for the “Ethernet setup”...
Other useful features Photo mode Slide show Selecting the BGM Viewing thumbnails Setup the slide show BGM from “Select slide show BGM” by pressing B when selecting photo thumbnails. This bar is not shown in the “Home network” screen. Buttons for thumbnail operations This bar is not shown in the “Home network”...
Other useful features NOTE Music mode • “Video mode” is only available for USB mode. • Instead of pressing buttons on the remote control unit, the operations above are also available on the screen with the operation panel. You can call up this operation panel by pressing CONTROL on the remote control unit or select “Control (USB)”...
Other useful features NOTE View setting • Progressive format jpeg files are not supported. • Music files or video files in USB 1.1 devices may not be played DivX® setup properly. • Operation using USB hubs is not guaranteed. • Some video file formats may not be played depending on the This is the function to confirm your registration code.
Connecting a PC After connecting Connecting a PC You must also set “RGB” from the “Input select” menu when selecting “EXT 3” from the “INPUT” menu (Pages 17 and 42). HDMI connection NOTE • The PC input terminals are DDC1/2B-compatible. HDMI 1, 2, 3 or 4 •...
Connecting a PC Adjusting the PC image Adjusting the PC image manually automatically Option Option Fine sync. Auto sync. Ordinarily you can easily adjust the picture as necessary to change image position using “Auto sync.”. In some This function enables the screen to be automatically cases, however, manual adjustment is needed to adjusted to its best possible condition when the analogue optimise the image.
Connecting a PC Command format RS-232C port specifications Eight ASCII codes +CR PC control of the TV C1 C2 C3 C4 P1 P2 P3 P4 • When a programme is set, the TV can be controlled from the PC using the RS-232C terminal. The input signal (PC/video) can be selected, the volume can be adjusted and various other adjustments and settings ...
Page 53
Connecting a PC RS-232C command list CONTROL ITEM COMMAND PARAMETER CONTROL CONTENTS CONTROL ITEM COMMAND PARAMETER CONTROL CONTENTS POWER O W R POWER OFF (STANDBY) VOLUME VOLUME (0_60) SETTING POSITION H-POSITION (AV/PC) INPUT INPUT SWITCHING V-POSITION (AV/PC) SELECTION A (TOGGLE) CLOCK (0_180) TV (CHANNEL FIXED) PHASE (0_40)
Appendix Troubleshooting Problem Possible solution • No power. • Turn on (;) the MAIN POWER switch on the rear of the TV (Page 4). • Is the AC cord disconnected? Check if you pressed <a on the TV. • • The TV cannot be operated.
Updating your TV via DVB-T Getting update information Ensure that your TV software version is always up to Information date. From time to time SHARP will make updated TV base software and DVB software available. Message list View setting When new software is detected, you can confirm the...
Appendix The TV displays a confirmation screen while Updating your TV via USB checking the data in the inserted USB device. CAUTION Information • If the data is not compatible with the system, an error message appears on the screen. Repeat steps 2 and 3 after pressing Software update •...
The copyrights for the software components and various relevant documents included with this product that were developed or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws. This product also makes use of freely distributed software and software components whose copyrights are held by third parties.
• As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be...
• This TV should be mounted on a wall only with the wall mount bracket and attachment* available from SHARP (Page 57). The use of other wall mount brackets may result in an unstable installation and may cause serious injuries.
SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg SHARP CORPORATION http://www.sharp-eu.com Printed in Poland Gedruckt in Polen Imprimé en Pologne Stampato in Polonia Gedrukt in Polen Impreso en Polonia Impresso na Polónia Polonya’da basılmıştır Надруковано в Польщі Напечатано в Польше...