Related Manuals for Husqvarna 324R X-series
Summary of Contents for Husqvarna 324R X-series
- Page 1 Operator′s manual 324R X-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
KEY TO SYMBOLS Symbols WARNING! Clearing saws, Wear sturdy, non-slip boots. brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the Only use non-metallic, flexible operator’s manual. -
Page 3: Table Of Contents
CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Symbols ..............2 Please read the operator’s manual carefully. CONTENTS Contents ............... 3 WARNING! Long-term exposure to noise can result in permanent hearing Note the following before starting: ......3 impairment. -
Page 4: Introduction
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. -
Page 5: What Is What
WHAT IS WHAT? What is what on the brush cutter? Blade 16 Air filter cover Grease filler cap, bevel gear 17 Handle adjustment Bevel gear 18 Locking nut Cutting attachment guard 19 Support flange Shaft 20 Support cup Handlebar 21 Drive disc Throttle control 22 Trimmer head Stop switch... -
Page 6: General Safety Precautions
GENERAL SAFETY PRECAUTIONS Important Personal protective equipment IMPORTANT! IMPORTANT! The machine is only designed for trimming grass, grass A clearing saw, brushcutter or trimmer can be clearing and/or forestry clearing. dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It The only accessories you can operate with this engine is extremely important that you read and understand the unit are the cutting attachments we recommend in the... -
Page 7: Machine's Safety Equipment
GENERAL SAFETY PRECAUTIONS BOOTS control and the throttle lockout both move back to their original positions. This movement is controlled by two Wear boots with steel toe-caps and non-slip sole. independent return springs. This arrangement means that the throttle control is automatically locked at the idle setting. - Page 8 GENERAL SAFETY PRECAUTIONS be checked. See instructions under the heading Vibration damping system Maintenance. Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier. Stop switch Using incorrectly wound cord or a blunt or incorrect cutting attachment (wrong type or incorrectly filed, see Use the stop switch to switch off the engine.
- Page 9 GENERAL SAFETY PRECAUTIONS under the heading Adjusting the harness and brush Regularly check that the muffler is securely attached to cutter. the machine. Check that the harness straps are correctly positioned. Once the harness and machine have been adjusted, check that the harness quick release works correctly. If the muffler on your machine is fitted with a spark Muffler arrestor mesh this must be cleaned regularly.
-
Page 10: Cutting Equipment
GENERAL SAFETY PRECAUTIONS When fitting, tighten the nut in the opposite direction to the WARNING! Always stop the engine direction of rotation of the cutting attachment. To remove before doing any work on the cutting it, undo the nut in the same direction as the cutting attachment. -
Page 11: Sharpening Grass Cutters And Grass Blades
GENERAL SAFETY PRECAUTIONS Keep the correct setting on the saw blade! Follow our A correctly sharpened blade is essential for working instructions and use the recommended setting tool. An efficiently and to avoid unnecessary wear to the blade and incorrectly set saw blade increases the risk of jamming brush cutter. -
Page 12: Trimmer Head
GENERAL SAFETY PRECAUTIONS Trimmer head IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise the machine will generate harmful vibration. • Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engine size. -
Page 13: Assembly
ASSEMBLY Fitting the handlebar Transport position, handlebar • Remove the screw at the rear of the throttle handle. • The handlebar can easily be turned to fit along the • Slide the throttle handle onto the right side of the shaft for easier transportation and storage. -
Page 14: Fitting A Blade Guard, Grass Blade And Grass Cutter
ASSEMBLY Fitting a blade guard, grass blade Fitting the blade guard and saw and grass cutter blade • Remove the mounting plate (H). Fit the adapter (I) and bracket (J) with the two screws (K) as shown. Fit the blade guard (A) to the adapter using the 4 screws (L) as shown. -
Page 15: Fitting A Trimmer Guard And Superauto Ii 1" Trimmer Head
ASSEMBLY the spanner in the opposite direction to the direction Insert a finger into the centre hole of the cover (I) while of rotation (Caution! left-hand thread). grasping the cover with your other fingers. Using the index finger and thumb of your other hand, release the two catches (J) that engage in the cut-outs in the bottom half (K). -
Page 16: Adjusting The Harness And Brush Cutter
ASSEMBLY guard onto the fitting on the shaft and secure it with situation that requires you to free yourself from the the bolt (L). machine and harness. Spreading the load on your shoulders A well-adjusted harness and machine makes work much easier. -
Page 17: Fuel Handling
Contact your local petrol operation. station to find out where to dispose of excess fuel. • For the best result and function use HUSQVARNA • The transport guard must always be fitted to the engine oil. - Page 18 FUEL HANDLING When the oil level is low, top up using engine oil to the edge of the oil refill hole. Only use recommended engine oil. Fuelling WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke or place hot objects near fuel.
-
Page 19: Starting And Stopping
STARTING AND STOPPING Check before starting trimmer guard if they have been exposed to impact or are cracked. • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been... -
Page 20: Warm Engine
STARTING AND STOPPING Primer bulb: Press the air purge repeatedly until fuel Starting begins to fill the bulb. The bulb need not be completely filled. WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately. -
Page 21: Working Techniques
WORKING TECHNIQUES General working instructions yourself incorrectly or make the cut in the wrong place the tree may hit you or the machine and cause you to lose control. Both situations can cause serious IMPORTANT! personal injury. This section describes the basic safety precautions for working with brush cutters and trimmers. - Page 22 WORKING TECHNIQUES • Control the felling direction (take advantage of the • Start at whichever end of the area is easiest, and clear wind). an open space from which to work. • Work systematically to and fro across the area, WARNING! Neither the operator of the clearing a width of around 4-5 m on each pass.
-
Page 23: Brush Cutting With A Saw Blade
WORKING TECHNIQUES • To fell to the left, the bottom of the tree should be wood. Small stems require more pressure, while large pushed to the right. Tilt the blade and bring it stems require less pressure. diagonally down to the right, exerting firm pressure. At the same time push the stem using the blade guard. -
Page 24: Grass Clearing Using A Grass Blade
WORKING TECHNIQUES Grass clearing using a grass blade can also damage sensitive bark on trees and bushes, and damage fence posts. • Reduce the risk of damaging plants by shortening the cord to 10-12 cm and reducing the engine speed. •... -
Page 25: Maintenance
MAINTENANCE Carburettor Muffler WARNING! The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch CAUTION! Some mufflers are fitted with a catalytic can come loose and cause personal converter. See chapter on Technical data to see whether injury. -
Page 26: Cooling System
The spark plug should be replaced after about a month in operation or earlier if necessary. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. -
Page 27: Bevel Gear
However, before using the machine you should check that the bevel gear is filled three-quarters full with grease. Use HUSQVARNA special grease. The grease in the bevel gear does not normally need to be changed except if repairs are carried out. -
Page 28: Maintenance Schedule
MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. -
Page 29: Technical Data
TECHNICAL DATA Technical data 324Rx Engine Cylinder displacement, cm 25,0 Cylinder bore, mm Stroke, mm Idle speed, rpm 3100 Recommended max. speed, rpm 11000 Speed of output shaft, rpm 8300 Max. engine output, acc. to ISO 8893, kW/ rpm 0,8 / 7000 Catalytic converter muffler Speed-regulated ignition system Ignition system... -
Page 30: Ec-Declaration Of Conformity
EC-declaration of conformity (Applies to Europe only) We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the brush cutters Husqvarna 324Rx with serial numbers dating from 2009 onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:... - Page 31 Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...
- Page 33 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
- Page 34 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
- Page 35 T35, T35x 8,5 m 10 cm 4" 4,3 m "Clic" 15 cm 6"...
- Page 36 Original instructions 1153287-26 ´®z+U<h¶64¨ ´®z+U<h¶64¨ 2010-03-30...