A substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate. GD15N*/GD15A*...
CONFIDENTIAL 3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the GD15N*/GD15A* monitors. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1 Disassembly Cautions:1. Disconnect the monitor from the power source before disassembly.
6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts. 7. To protect aganist shock hazard,use an isolation transform. GD15N*/GD15A*...
Check IC101. appear at Pin 4 of IC101? Does proper DC 2.5 V appear at Check IC199, IC104. Pin 2, 4 of IC109, IC104? Does proper DC 3.3 V Check IC103. appear at Pin 3 of IC103? Check IC201. GD15N*/GD15A*...
Page 38
CONFIDENTIAL 7 Electrical Parts List Memo 7-16 GD15N*/GD15A*...
Page 39
CONFIDENTIAL 6 Exploded View & Parts List Memo GD15N*/GD15A*...
Page 40
RA306 ~ RA311? Does the clock pulse Check IC204 and related circuit of IC204. appear at Pin 12 of IC204? Does the clock pulse appear at Replace IC403. output Pin 39, 40 of IC403? Replace LCD Panel. GD15N*/GD15A*...
Page 41
Check Pin 8 (AGC) Check replace the tuner. of IC703 (CN402). Check Pin 72, 73, 74 of IC402. Replace IC402. Check related circuit of Does the signal appear at D405. D405 and replace D405. Check IC301 and replace mainboard. GD15N*/GD15A*...
Does the low signal Check related circuit of at R528, R529? R528, R529 and replace. Check Pin 14, 17 Replace IC502. of IC502 (TDA7496). Check Pin 60, 67 of Replace IC501 (MSP25/10). IC501 (MSP25/10). Check related circuit of IC501, IC502 and tuner. GD15N*/GD15A*...
Page 43
CONFIDENTIAL 4 Alignments and Adjustments Memo GD15N*/GD15A*...
Page 44
3-2 Replacement Order of Lamp Assemblies 1. After confirm there is nothing on the desk Turn the LCD module over and put it on a flat desk set to the ground. 2. Push down the stopper and slide the lamp unit. GD15N*/GD15A*...
Page 45
LCD module : opposite process 2 and 3 Replacement of lamp unit should be done at the power off state and rcommended clean bench condition. 3-3 Reassembly Reassembly procedures are in the reverse order of Disassembly procedures. GD15N*/GD15A*...
Page 46
CONFIDENTIAL 3 Disassembly and Reassembly Memo GD15N*/GD15A*...
GND-Green GND-Blue GND-Blue GND-Blue No Connection No Connection Not Used GND-Sync/Self Test GND-Sync/Self Test GND-Sync/Self Test DDC Data DDC Data DDC Data Horizontal sync H/V-Sync Not Used Vertical sync Not Used Not Used DDC Clock DDC Clock DDC Clock GD15N*/GD15A*...
Page 48
CONFIDENTIAL 2 Product Specifications 2-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1 Timing Chart GD15N*/GD15A*...
Page 49
Sync. width 0.057ms 0.106ms 0.125ms 0.064ms 0.106ms Back porch 0.626ms 0.607ms 0.478ms 0.448ms 0.513ms Sync. polarity Positive Positive Positive Positive Negative or Negative Dot Clock 36.000MHz 40.000MHz 50.000MHz 49.500MHz 75.000MHz Sync. Type Separate Separate Separate Separate Separate Scan Type GD15N*/GD15A*...
Page 50
12.795ms 13.714ms 12.549ms Front porch 0.017ms 0.086ms 0.020ms Sync. width 0.050ms 0.086ms 0.060ms Back porch 0.466ms 1.114ms 0.784ms Sync. polarity Positive Negative Negative Dot Clock 78.750MHz 30.240MHz 57.284MHz Sync. Type Separate Separate Separate Composite Composite Sync.-on-G Sync.-on-G Scan Type GD15N*/GD15A*...
Use only an anti-static solder removal device. Some brushing clothes together, or lifting your foot from solder removal devices not classified as “anti-static” a carpeted floor can generate enough static can generate electrical charges sufficient to damage electricity to damage an ESD. ESDs. GD15N*/GD15A*...
Page 53
Samsung Electronics Co.,Ltd. 416, Maetan-3Dong, Paldal-Gu, Suwon City, Kyungki-Do, Korea. Printed in Korea P/N : BN81-00032A-00 http://www.samsungmonitor.com (SyncMaster Worldwide) http://www.samsung-monitor.com (SyncMaster USA) http://www.sec.co.kr/monitor (Korea)