70FW-53E SERVICE MANUAL SE0070FW53E00 Issued: 01 August 2002 DA-50W CHASSIS / SECAM SYSTEM COLOUR TELEVISION B/G I L L’ B/G D/K MODEL 70FW-53E E/ENL/ECG/I/SE SHARP In the interests of user safety (required by safety regulations in some countries) the set should restored to its original condition and only parts identical to those specified should be used.
Page 2
70FW-53E SERVICE MANUAL UPDATE LOG SHEET Technical Report No. Application Cause / Solution Part No. Page No. Data /Serial No. Technical Bulletin No. Use this page to keep any special servicing information as Technical Report (Bulletin), Technical Information, etc. If only part number changes are required, just change part number directly the part number in the Parts Listing Section.
PFC Circuit (Power Filter Correction), on every TV set manufac- tured from January 2001. On TV set manufactured before the above date (Serial Number 800929 for 70FW-53E or previous), this modification is not required.
70FW-53E IMPORTANT SERVICING NOTES Only qualified service personnel are allowed to carry out maintenance and repair of this receiver. SERVICING OF HIGH VOLTAGE SYSTEM AND CRT It is important that the static charge is removed from the high voltage system when carrying out work on the receiver.
70FW-53E ADJUSTMENT PROCEDURES All adjustments to this chassis, except for focus, are carried out in the Service Mode. • • • • • SERVICE MODE The Service Mode is provided to enable the engineer to correctly set up the receiver to the CRT fitted in the set.
Page 6
70FW-53E Note that the receiver should be set to FULL MODE before carrying out any geometry adjustments. This can be achieved by pressing the wide-screen mode button on the remote control until FULL MODE appears on the OSD. This can only be done out of the Service Mode.
Page 7
70FW-53E • When the volume down button is pressed, side pincushion changes from barrel shape to pincushion. • Press the stand-by button on the remote control to store. LOWER CORNER CORRECTION Adjust the LOWER CORNER CORRECTION so that the picture is centred.
Page 8
70FW-53E Colour Adjustments The following adjustments should only be carried out when the CRT or IC1801 are replaced. G2, Cut Off and Gain Adjustments 1. Follow the procedure below to set the G2 1.1 Tune the set to the output of a signal generator (cross hatch pattern).
Page 9
5. If another NVM value has to be changed, use the channel down button to select the page or position and repeat as necessary. Note: DO NOT change any NVM data, unless you have been advised to do so by a Sharp representative. If data is incorrectly changed, serious damage may occur to the receiver. Contrast Adjustments Three types of contrast levels can be varied as listed below: •...
Page 14
70FW-53E DYNAMIC FOCUS UNIT PWB (F7314N3). SYMBOL " " WITH INDICATED SECTION ACTIVE CAUTION C1701 R1707 D1701 D1702 R1709 C1703 CAUTION THE ACTIVE SECTION IS INDICATED WITH THE " " SYMBOL IC1701 FB1701 C1704 R1710 R1710 R1712 C1704 D1703 D1703...
Page 16
70FW-53E POWER SWITCH UNIT PWB (F7266N1). Component Side CAUTION D6751 D6752 THE ACTIVE SECTION IS INDICATED WITH OPC1 THE " " SYMBOL LP6701 IC6701 R6701 S6702 S6703 C6701 R6702 L6701 F7266BMN1 F6701 K7266BM T3.15AH (AA) C6746 Copper Side IC6701 R6738...
70FW-53E DESCRIPTION OF SCHEMATIC DIAGRAM NOTE: SAFETY NOTE: 1. The unit of resistance «ohm» is omitted (K=1000 ohms. M= Megaohm). 1. DISCONNECT THE AC PLUG FROM THE AC 2. All resistors are 1/8 watt. unless otherwise noted. OUTLET BEFORE REPLACING PARTS.
Page 25
70FW-53E SCHEMATIC DIAGRAM OF CRT SOCKET UNIT (F7273N3), 00 Version.
Page 26
70FW-53E SCHEMATIC DIAGRAM OF MOTHER UNIT (F7240NKA), 00 Version. Page 28...
Page 27
70FW-53E SCHEMATIC DIAGRAM OF MOTHER UNIT (F7240NKA), 00 Version. Page 29...
Page 28
70FW-53E SCHEMATIC DIAGRAM OF MOTHER UNIT (F7240NKA), 00 Version. Page...
Page 29
70FW-53E SCHEMATIC DIAGRAM OF MOTHER UNIT (F7240NKA), 00 Version. Page...
Page 30
70FW-53E SCHEMATIC DIAGRAM OF DYNAMIC FOCUS UNIT (F7314N3), 00 Version.
Page 31
70FW-53E SCHEMATIC DIAGRAM OF POWER SWITCH UNIT (F7266N1), 00 Version.
Page 32
J 4 0 1 0 0 1 5 B C N 4 J A K J 0 0 4 7 C E Z Z C 4 2 8 1 n F C 4 2 9 1 5 4 3 2 6 7 1 n F C 3 3 6 C 3 3 7...
Page 33
D 1 3 0 3 ( V S ) 6 V 8 E X 0 4 1 1 I C 1 3 0 0 V H I B A 4 5 5 8 R 1 3 0 4 ( 0 ) G N 0 3 4 1 D 1 3 0 4 6 V 8...
70FW-53E PARTS LISTING 5() 1R 3$576 '(6&5,37,21 61 &2'( (; &2'( REPLACEMENT PARTS Replacement parts which have special safety characteristics are identified in this manual. Electrical components having such features are identified in the Replacement Part List. The use of a substitute replacement part which does not have the same safety characteristics as the factory recommended is not permitted.
70FW-53E STEREO LED FLASHING CODES If the TV set does not work and the stereo led is flashing, follow the sequence according to the information below, as a guide to fault finding. 1. Unable to read or write into NVM: 66% ON, 33% OFF twice and OFF for a second.
70FW-53E PACKING OF THE SET Pack-ad SPAKX4050BMZZ Wrapper SPAKP2006BMZZ Front Carton Box SPAKC5497BMZZ Remote Control RRMCG1070BMSA Batteries UBATU0013TAZZ...