About This Guide This guide provides information on monitor features, setting up the monitor, and technical specifications. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.
Mounting the Monitor ......................9 Installing a Cable Lock ........................10 3 Finding More Information ..........................11 4 Technical Specifications ..........................12 LE1902x Model ..........................12 LE2002x and LE2002xm Models ....................... 12 LE2202x Model ..........................13 Recognizing Preset Display Resolutions .................... 13 LE1902x Model ........................
The LCD (liquid crystal display) monitors have an active matrix, thin-film transistor (TFT) panel. The monitor models and features include: ● LE1902x model, 47.0 cm (18.5-inch) diagonal viewable area display with 1366 x 768 resolution, plus full-screen support for lower resolutions; includes custom scaling for maximum image size while preserving original aspect ratio ●...
Page 8
● Intelligent Management AssetControl ● Compliant with the following regulated specifications: ◦ European Union CE Directives ◦ Swedish TCO Requirements Chapter 1 Product Features ENWW...
Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow the instructions below. Attaching the Monitor Base Lift the base from the monitor box and set it on a flat surface such as a table top. Using both hands, lift the monitor from its box, position the pedestal over the base, and press down firmly to lock it in place.
Rear Components Figure 2-2 Rear Components Component Function AC Power Connector Connects the AC power cord to the monitor. Audio Connector (select Connects the audio cable to the monitor. models) DVI-D (select models) Connects the DVI-D cable to the monitor. Connects the VGA cable to the monitor.
Connecting the Cables Place the monitor in a convenient, well-ventilated location near the computer. Remove the cable management clip from the pedestal by pulling outward on the two sides of the clip (1) then lifting the clip off the pedestal (2). Figure 2-3 Removing the Cable Management Clip Connect a VGA signal cable or DVI-D signal cable (select models).
Page 12
Connect one end of the power cord to the AC power connector on the back of the monitor, and the other end to an electrical wall outlet. Figure 2-4 Connecting the Cables WARNING! To reduce the risk of electric shock or damage to the equipment: Do not disable the power cord grounding plug.
Front Panel Controls Figure 2-6 Monitor Front Panel Controls Table 2-1 Monitor Front Panel Controls Control Function Menu Opens, selects or exits the OSD menu. Minus If the OSD menu is on, press to navigate backward through the OSD menu and decrease adjustment levels. If the OSD menu is inactive, press to activate the volume adjustment bar.
Adjusting the Monitor Tilt the monitor's panel forward or backward to set it to a comfortable eye level. Figure 2-7 Tilting the Monitor Turning on the Monitor Press the power button on the computer to turn it on. Press the power button on the front of the monitor to turn it on. CAUTION: Burn-in image damage may occur on monitors that display the same static image on screen for a prolonged period of time.* To avoid burn-in image damage on the monitor screen, you...
Removing the Monitor Pedestal Base You can remove the monitor panel from the pedestal base to install the panel on a wall, a swing arm, or other mounting fixture. CAUTION: Before beginning to disassemble the monitor, be sure the monitor is turned off and the power and signal cables are both disconnected.
To attach the monitor to a swing arm, insert four 10mm screws through the holes on the swing arm plate and into the mounting holes on the monitor. Figure 2-9 Mounting the Monitor To attach the monitor to other mounting fixtures, follow the instructions included with the mounting fixture to ensure that the monitor is safely attached.
Finding More Information HP LCD Monitors Reference Guide Refer to the included on the CD with your monitor for additional information on: ● Optimizing monitor performance ● Safety and maintenance guidelines ● Installing software from the CD ● Using the OSD menu ●...
Technical Specifications NOTE: All specifications represent the typical specifications provided by HP's component manufacturers; actual performance may vary either higher or lower. LE1902x Model Table 4-1 LE1902x Specifications Maximum Weight (Unpacked) 2.8 kg 6.17 lbs Dimensions (include base) 33.89 cm 13.34 inches...
The display resolutions listed below are the most commonly used modes and are set as factory defaults. This monitor automatically recognizes these preset modes and they will appear properly sized and centered on the screen. LE1902x Model Table 4-4 Factory Preset Modes...
Page 21
utilize .5 watts of power. There is a brief warm up period before the monitor will return to its normal operating mode. Refer to the computer manual for instructions on setting energy saver features (sometimes called power management features). NOTE: The above power saver feature only works when connected to computers that have energy saver features.