Related Manuals for Husqvarna LE389
Summary of Contents for Husqvarna LE389
- Page 1 LE389 1.1997 Spare Parts Owner's Manual 601 00 22 32 Piéces Dètachées Reference No. 710386 10/08/96...
-
Page 2: Safety Rules
SAFETY RULES THESE SAFETY RULES ARE FOR YOUR PROTECTION. READ THEM CAREFULLY. IMPORTANT Safety standardsrequire operator presence controls to minimize the risk of injury. Your Edger/ Trimmer is equipped with such controls. Do not attempt to defeat the function of the operator presence control under any circumstances. -
Page 3: Table Of Contents
OWNER'S INFORMATION Record the following information about your unit so that you will be able to provide it in case of loss or theft. (Enter complete 8 digit number MODEL NUMBER: from model plate on unit) SERIAL NO.: CODE NO.: PURCHASE DATE: DEALER'S NAME AND ADDRESS: TELEPHONE:... -
Page 4: Assembly
ASSEMBLY CAUTION : Always wear safety Clutch Lever glasses or eye shields while assembling Edger/Trimmer. Fig.1-ASSY to the right shows the Edger/ Control Rod Trimmer completely assembled. Handle References to the right or left hand side of the Panel Edger/Trimmer are from the viewpoint of the operator's position behind the unit. -
Page 5: Handle
• Attach the front wheels to the Edger/Trim- Upper Handles (in operating position) mer shown in Fig. 5-ASSY with a 5/16-18 Clutch x 4.50 inch hex head screw, four 11/32 x Hair Pin Lever 11/16 inch flatwashers, two spacers and a 5/16-18 hex head wide flange locknut found in parts bag. -
Page 6: Operation
OPERATION KNOW YOUR EDGER/TRIMMER READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR EDGER/TRIMMER. Compare the illustrations with your EDGER/TRIMMER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. FAST PRIMER Slow Primer Button Stop... - Page 7 HOW TO USE YOUR EDGER WARNING : The operation of this Edger/ Trimmer can result in foreign objects being thrown into the eyes, which can cause severe eye damage. Always wear safety glasses or eye shields while operating the Edger/Trim- mer.
- Page 8 • Remove the oil fill cap-dipstick and fill the • Loosen T- knob on the inside right rear crankcase to FULL line on dipstick. See Fig. of the main frame that secures the wheel 5-OP. Check frequently when filling the support rod as shown in Fig.
-
Page 9: Maintenance
• TO START THE ENGINE To stop the engine, make sure the clutch lever is all the way back or up and move Before starting the engine, be sure you have the throttle control lever to the STOP read and understood all the instructions on the preceding pages. -
Page 10: 9" Edger/Trimmer
GENERAL RECOMMENDATIONS • Clean the cover and the flange thor- oughly. The warranty on this Edger/Trimmer does not cover items that have been subjected to op- • Insert the new air filter into the cover. erator abuse or negligence. To receive full •... -
Page 11: Service And Adjustments
CAUTION : Always stop the engine and disconnect the spark plug wire before making any repairs to the Edger/Trimmer. SERVICE AND ADJUSTMENTS V-BELT REPLACEMENT Your Edger/Trimmer is equipped with a V-belt made of a special compound. If the belt be- comes worn or breaks, replace it with an orignal equipment belt as shown in the Repair Parts section of this manual. -
Page 12: Storage
adjusting, see your nearest Authorized Ser- Tightening vice Center. Wrench IMPORTANT Never tamper the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can Holding Wrench be dangerous. If you think the engine-gov- Blade erned high speed needs adjusting, contact Locknut... -
Page 13: Troubleshooting
TROUBLE SHOOTING CAUSE TROUBLE CORRECTION Stale fuel Drain fuel tank. Fill with fresh Difficult starting fuel Defective spark plug Clean and re-gap or replace Replace fuel filter Clogged fuel line Engine runs Clean fuel line; check gas tank Blocked fuel line or empty fuel tank erratic Have carburetor adjusted Carburetor out of adjustment...