Husqvarna YTH22V46XLS Owner's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Lawn Mower
  5. HUSQVARNA YTH22V46XLS
  6. Owner's manual

Husqvarna YTH22V46XLS Owner's Manual

Husqvarna lawn mower user manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

07002
YTH22V46XLS
Owner's Manual
532 43 87-04

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna HUSQVARNA YTH22V46XLS

Summary of Contents for Husqvarna HUSQVARNA YTH22V46XLS

  • Page 1 07002 YTH22V46XLS Owner's Manual 532 43 87-04...

  • Page 2: Safety Rules

    Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent ac ci den tal starting when setting up, trans port ing, ad just ing or making repairs, al ways dis con nect spark plug wire and place...
  • Page 3 Safe Operation Practices for Ride-On Mowers III. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the ma chine and the mowing activity. Never assume that children will remain where you last saw them. •...

  • Page 4: Table Of Contents

    PRODUCT SPECIFICATIONS Gasoline Capacity 3.0 Gallons and type: Unleaded Regular Oil Type (API-SG-SL): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) Oil Capacity: W/ Filter: W/O Filter: Spark Plug: Champion QC12YC (Gap: .040") Ground Speed (MPH): Forward: Reverse: Charging System: 16 AMPS @ 3600 RPM Battery: AMP/HR:...

  • Page 5: Assembly

    UNASSEMBLED PARTS Keys (2) Keys Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Stan dard wrench sizes are listed. (1) 1/2"...

  • Page 6: Assembly

    NOTE: You may now roll your tractor off the skid. Follow the instructions below to remove the tractor from the skid. WARNING: Before start ing, read, un der stand and fol low all in struc tions in the Op er a tion section of this man u al. Be sure tractor is in a well-ventilated area.

  • Page 7: Operation

    These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. REVERSE NEUTRAL REVERSE ENGINE OFF OPERATION SYSTEM (ROS) LIGHTS ON BATTERY FUEL ATTACHMENT ATTACHMENT CLUTCH DISENGAGED CLUTCH ENGAGED FREE WHEEL (Automatic Models only) Failure to follow instructions could result in serious injury or death.
  • Page 8 KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the applicable safety standards of the American National Standards Institute. (A) ATTACHMENT LIFT LEVER - Used to raise and lower the mower or other attachments mounted to your tractor.
  • Page 9 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. We rec om mend standard safety glasses or a wide vision safety mask worn over spectacles.
  • Page 10 TO MOVE FORWARD AND BACKWARD (See Fig. 7) The direction and speed of movement is controlled by the forward and reverse drive pedals. • Start tractor and release parking brake. • Slowly depress forward (K) or reverse (L) drive pedal to begin movement.
  • Page 11 TO STOP MOWER BLADES • Disengage at tach ment clutch con trol. CAUTION: Do not operate the mower without either the en tire grass catcher, on mowers so equipped, or the deflector shield (S) in place (See Fig. 10). Fig. 10 REVERSE OPERATION SYSTEM (ROS) Your tractor is equipped with a Reverse Operation System (ROS).

  • Page 12: Before Starting The Engine

    BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine in your tractor has been shipped, from the factory, already filled with sum mer weight oil. • Check engine oil with tractor on level ground. • Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level.

  • Page 13: Purge Transmission

    PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. To ensure proper operation and performance, it is rec om - mend ed that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de vel - oped during shipping of your tractor.

  • Page 14: Maintenance Schedule

    MAINTENANCE SCHEDULE Check Brake Operation Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades Lubrication Chart Check Battery Level Clean Battery and Terminals Clean Debris Off Steering Plate ck Transaxle Cooling Check Mower Levelness ck V-Belts Check Engine Oil Level Change Engine Oil (with oil filter)

  • Page 15: Maintenance

    TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed. (See “TO CHECK BRAKE”...

  • Page 16: Clean Air Screen

    TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to ensure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent pos- si ble damage to seals, do not use high pressure water or steam to clean transmission.

  • Page 17: Spark Plugs

    MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.

  • Page 18: Service And Adjustments

    SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. •...
  • Page 19 SERVICE AND ADJUSTMENTS • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring. • Repeat on opposite side of tractor. Fig. 21 • ATTACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with washer and...
  • Page 20 SERVICE AND ADJUSTMENTS TO LEVEL MOWER Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.
  • Page 21 SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 30) MOWER DRIVE BELT REMOVAL • Park tractor on a level surface. En gage parking brake. • Lower attachment lift lever to its lowest position. • Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.
  • Page 22 SERVICE AND ADJUSTMENTS TO CHECK BRAKE If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be serviced. You may also check brake by: •...

  • Page 23: Interlocks And Relays

    SERVICE AND ADJUSTMENTS REPLACING BATTERY (See Fig. 34) WARNING: Do not short battery ter mi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from ac ci den tal grounding.

  • Page 24: Storage

    Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.

  • Page 25: Trou Ble Shoot Ing

    TROUBLESHOOTING POINTS PROBLEM CAUSE 1. Out of fuel. Will not start 2. Engine not “CHOKED” properly. 3. Engine flooded. 4. Bad spark plug. 5. Dirty air filter. 6. Dirty fuel filter. 7. Water in fuel. 8. Loose or damaged wiring. 9.
  • Page 26 TROUBLESHOOTING POINTS PROBLEM CAUSE Engine continues 1. Faulty operator-safety presence control system. to run when oper- ator leaves seat with attachment clutch engaged 1. Worn, bent or loose blade. Poor cut - uneven 2. Mower deck not level. 3. Buildup of grass, leaves, trash under mower. 4.

  • Page 27: Repair Parts

    SCHEMATIC SCH13 RELAY PTO SWITCH (MATING SIDE) IGNITION SWITCH POSITION CIRCUIT “MAKE” M+G+A1 B+A1 RUN/OVERRIDE B+A1 L+A2 START B + S + A1 BATTERY FUSE AMMETER (OPTIONAL) WHITE PTO SWITCH (DISENGAGED) WHITE BLACK BLUE BLACK BLACK BLACK BLACK BLACK BLUE BLACK IGNITION UNIT...
  • Page 28 TRACTOR - - MODEL NUMBER YTH22V46XLS (96043011200), PRODUCT NO. 960 43 01-12 ELECTRICAL T27S With 12V Outlet Option...
  • Page 29 ELECTRICAL PART DESCRIPTION 532 16 34-65 Battery 874 76 04-12 Bolt Hex Head 1/4-20 x 3/4 532 18 64-91 Box Battery 532 17 61-38 Switch Interlock Push-In 532 40 02-52 Harness Socket Light w/4152J 532 00 41-52 Bulb Light 532 40 02-53 Cable Battery 532 41 28-95 Cable Starter...
  • Page 30 CHASSIS chassis-tex_GT HUSQ II_1...
  • Page 31 CHASSIS PART DESCRIPTION 532 43 97-52 Applique Subasm. 532 43 74-69 Dash 532 43 97-25 Hood 532 43 97-33 Lens LH 532 43 77-62 Grille 532 43 97-32 Lens RH 532 19 61-25 Plate Engine 817 06 05-12 Screw 5/16-18 x 3/4 532 42 36-94 Fender 873 68 05-00...
  • Page 32 TRACTOR - - MODEL NUMBER YTH22V46XLS (96043011200), PRODUCT NO. 960 43 01-12 DRIVE drive-tex_K46_pedal_26_r2...
  • Page 33 DRIVE PART DESCRIPTION - - - - - - - - - - Transaxle, TUFFTORQ K46BT 532 12 35-83 Key 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga. 532 41 36-78 Spring, Brake 532 19 96-79 Spring Return Cruise 532 40 38-06 Rod, Brake 812 00 00-01 Ring E 532 43 54-86 Rod, Brake, Park...
  • Page 34 TRACTOR - - MODEL NUMBER YTH22V46XLS (96043011200), PRODUCT NO. 960 43 01-12 ENGINE engine-tex_bs-2cyl_23...
  • Page 35 ENGINE Engine Power Rating Information The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive En- gineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05).

  • Page 36: Steering Assembly

    STEERING ASSEMBLY steering-tex_HUSQHR_1_r1 53 8...
  • Page 37 STEERING ASSEMBLY PART DESCRIPTION 532 43 97-40 Wheel, Steering 532 19 59-68 Axle Asm., Front 532 40 30-87 Spindle Asm., LH 532 40 30-88 Spindle Asm., RH 532 12 49-31 Bearing, Race Thrust Harden 532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga. 812 00 00-29 Ring, Klip #T5304-75 532 12 12-32...
  • Page 38 TRACTOR - - MODEL NUMBER YTH22V46XLS (96043011200), PRODUCT NO. 960 43 01-12 SEAT ASSEMBLY PART DESCRIPTION 532 42 40-71 Seat 532 18 01-66 Bracket Pivot Fender 532 14 06-75 Strap, Asm Fender 873 80 06-00 Nut, Lock W/Ins. 3/8-16 unc 532 12 41-81 Spring, Seat Cprsn 532 17 18-77...

  • Page 39: Mower Lift

    MOWER LIFT lift-tex_17_r3 PART DESCRIPTION 532 42 20-27 Shaft Asm., Lift 532 19 52-31 Lever Lift Handle 532 41 15-55 Grip, Lever 532 19 63-14 Spring Torsion 532 19 42-09 Pin Cotter 7/16 Bow Tie Lock 532 41 07-10 Spring Lift Assist 819 19 19-12 Washer Clear Zinc 532 19 42-08...
  • Page 40 TRACTOR - - MODEL NUMBER YTH22V46XLS (96043011200), PRODUCT NO. 960 43 01-12 MOWER DECK 46_tex_lt_pred_25_r1...

  • Page 41: Mower Deck

    MOWER DECK KEY PART NO. NO. DESCRIPTION 532 42 16-49 Mower Housing 532 40 55-07 Cover Mandrel RH 532 40 55-06 Cover Mandrel LH 532 19 51-86 Arm Suspension 532 19 30-03 Bolt/Washer asm 7/16-20 unf 532 40 53-80 Blade Mower Hi Lift 532 19 28-72 Shaft Assembly, Mandrel 532 18 72-81...

  • Page 42: Wheels And Tires

    DECALS PART DESCRIPTION 532 41 16-57 Decal, Operators 532 42 91-96 Decal, Badge 532 43 95-85 Decal, Panel SD 532 43 29-14 Decal, Eng. HP 532 42 38-29 Decal, Customer Respons. 532 43 84-73 Decal, Replacement 532 41 86-00 Decal, Pedal Husq. Crown WHEELS AND TIRES wheel_art_1-tex 12 7...
  • Page 44 10.19.10 TH Printed in the U.S.A.

This manual is also suitable for:

Yth22v42ls

Table of Contents