9. Do not lift the CRT by the neck. 3. It is essential that service technicians have an accurate high voltage meter available at all times. Check the calibration of this meter periodically. CKB5237L/7227L...
Page 4
PLUG REVERSED (USING AC ADAPTER instructions are issued whenever appropriate. PLUG AS REQUIRED) Components identified by on schematics and EARTH GROUND parts lists must be sealed by a soldering iron after replacement and adjustment. Figure1-1. Leakage Current Test Circuit CKB5237L/7227L...
4. After servicing, always check that the screws, lead to the instrument chassis ground before components and wiring have been correctly connecting the positive lead; always remove reinstalled. Make sure that the area around the the instrument’s ground lead last. serviced part has not been damaged. CKB5237L/7227L...
Page 6
Some solder removal devices not classified as enough static electricity to damage an ESD. “anti-static” can generate electrical charges Indicates ESDs on the Schematic Diagram sufficient to damage ESDs. in this manual. CKB5237L/7227L...
110 MHz Active Display CKB5237L ; Horizontal : 267 mm ± 3 mm, Vertical : 200 mm ± 3 mm CKB7227L ; Horizontal : 306 mm ± 3 mm (4:3 ratio), Vertical : 230 mm ± 3 mm Input Voltage AC 90 to 264 Volts, 60 Hz or 50 Hz ±...
GND-R Green Blue H/V Sync Sense 0 DDC Return Green GND-R GND-G GND-G Sense 1 GND-B Reserved Reserved Blue GND-Sync/Self-raster Sense 2 DDC Data V-Sync H-Sync GND-B V-Sync DDC Clock H-Sync Figure 2-5. Male Type Figure 2-6. Male Type CKB5237L/7227L...
B : Horizontal sync width O : Frame time total P : Vertical sync width C : Back porch D : Active time Q : Back porch R : Active time E : Front porch S : Front porch CKB5237L/7227L...
Page 10
B : Horizontal sync width O : Frame time total P : Vertical sync width C : Back porch D : Active time Q : Back porch R : Active time E : Front porch S : Front porch CKB5237L/7227L...
Page 11
3 Opearating Instructions 3-1 Front View and Control 3-1-1 CKB5237L/7227L Front View – MENU EXIT Figure 3-2. Rear View Table 3-1. Front Panel Controls Location Symbol Description – Power Button MENU EXIT Power Indicator LED (Dual Color) Menu Display & Menu Exit...
– decrease the contrast. To access a function, use the menu button to move to its associated icon, and then use the – button to select the adjustment type. Then, push the ↵ button to access the function. CKB5237L/7227L...
Page 13
72 W (max.) Power Less than Less than 78 W 65 W Consumption/hr 15 W (nominal) (nominal) Table 3-3. Display Power Management Signaling (DPMS) ;CKB5237L Power saving function EPA/NUTEK State Normal Operation Stand-By Suspend Mode Power Off Mode Items Mode Position A...
4 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the CKB5237L/7227L monitors. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 4-1 Disassembly (CKB7227L) Cautions:1. Disconnect the monitor from the power source before disassembly.
Page 16
6. Set the monitor on its Base and make sure that the Main PCB and the Tilt Coil. the CRT faceplate was not scratched or 6. Replace all easily accessible ground wires on otherwise damaged. the CRT GND Assembly and Bottom Chassis. CKB5237L/7227L...
Page 17
4 Disassembly and Reassembly 4-3 Disassembly (CKB5237L) Cautions:1. Disconnect the monitor from the power source before disassembly. 2. Follow these directions carefully; never use metal instruments to pry apart the cabinet. 4-3-1 Cabinet Disassembly 4-3-3 Removing the Main PCB 1. With a pad beneath it, stand the monitor on its 1.
Page 18
4 Disassembly and Reassembly 4-4 Reassembly (CKB5237L) With the CRT facing downward on a protective pad, use the steps that follow to reassemble the monitor. 4-4-1 Replacing the CRT 7. Replace the Degaussing Coil at CN600 on the Main PCB.
Vertical: 50 Hz to 120 Hz (Automatic) Unless otherwise specified, adjust at the 17”: 1024 x 768 mode (68 kHz/85 Hz), 15”: 800 x 600 mode (54 kHz/85 Hz) signals. Refer to Table 2-1 on pages 2-4 and 2-5. CKB5237L/7227L...
Page 20
Computer with a video board that uses the ET-4000 chipset (strongly recommended if Figure 5-1 : Setup 1, With Signal Generator using Samsung DM 200 software) and that displays: 1024 x 768 @ 85 Hz, or 800 x 600 @ 85 Hz (minimum).
Horizontal: 16.7~19.2 Horizontal: Less than 0.90 mm 230 mm (17”) and 200 mm (15”). 5 : 4 (Tolerance: ± 3 mm.) Vertical : Less than 0.96 mm Vertical : 17.8~20.5 CKB5237L/7227L...
Page 22
5 Alignment and Adjustments 5-2-2 (a) HORIZONTAL LINEARITY ADJUSTMENT 5-2-4 Pinbalance Adjustment The CKB5237L/7227L monitors offer only Vertical CONDITIONS Linearity adjustments. Horizontal Linearity is Scanning frequency: 68 kHz/85 Hz (17”) fixed on the Chassis and is not adjustable. 54 kHz/85 Hz (15”)
Page 23
30 minutes. 5-2-9 To Delete the User Mode Data To delete the adjustment data from the user modes, click USER DELETE. Figure 5-7. Pincushion 5-2-10 Save the Data To save the adjustment data for a mode, press FACTORY SAVE. CKB5237L/7227L...
(for 15”) WHITE WINDOW 1. Select COLOR CHANNEL 1 to control the color for 9300K. 2. Adjust the luminance of the back raster to between 0.5 to 0.7 ft-L using the Screen VR Figure 5-9. Full White Pattern (T501) controls. CKB5237L/7227L...
Page 25
5-3-2 (c) steps 2 and 3. Scanning frequency: 68 kHz/85 Hz (17”) 54 kHz/85 Hz (15”) 5-3-3 (d) WHITE BALANCE ADJUSTMENT VERIFICATION Display image: Back raster pattern Refer to the procedure for 9300K, section 5-3-2 (d). Brightness: Maximum Contrast: Maximum CKB5237L/7227L...
Page 26
Color purity is the absence of undesired color. movement during shipping. Conspicuous mislanding (unexpected color in a uniform field) within the display area shall not be visible at a distance of 50 cm from the CRT surface. CKB5237L/7227L...
Page 28
Red and Blue Alignment Red, Blue and Green Alignment (4-pole magnet movement) (6-pole magnet movement) O-Magnetic VERTICAL Field MISALIGNMENT (1) SPREAD MAGNET HORIZONTAL MISALIGNMENT Motion (1) SHIFT DIRECTION OF CROSSHATCH PATTERN Motion (2) MOVE TOGETHER SHIFT DIRECTION OF CROSSHATCH PATTERN 5-10 CKB5237L/7227L...
Page 29
Bow convergence adjustments are not available Coil (X ). Turning it right raises the right end of for the CRTs used in the CKB5237L/7227L the blue line and lowers the left end. Turning the monitors. While all CRTs have bow convergence...
Page 30
5 Alignment and Adjustments Memo 5-12 CKB5237L/7227L...
CH1 P-P = 292 V CH1 RMS = 181.6 V CH1 P-P = 444 V CH1 RMS = 354.2 V CH1 P-P = 3.68 V CH1 RMS = 840 mV CH1 P-P = 3.80V CH1 RMS = 902 mV CKB5237L/7227L...
Page 32
Check Q403. Pin 1 of T401? WAVEFORMS 8.80 V (IC302, #26) 124.8 V (T401, #1) Check CN400, D403 and Q406. CH1 P-P = 8.80 V CH1 RMS = 6.176 V CH1 P-P = 124.8 V CH1 RMS = 66.16 V CKB5237L/7227L...
Page 33
Does switching pulse appear at Check Q503, Q510, Q512 and Q513. base and collector of Q503? CH1 P-P = 848 V CH1 RMS = 305.2 V Does signal appear at gate Check IC501 and FBT. of Q504 ? Check Q504, D508 and FBT. CKB5237L/7227L...
Page 34
Does H/V sync pulse Check signal cable connection appear at Pins 4 and the signal sources. and 10 of IC105? Check IC105. Does H/V sync output appear at Pins 20 Check Micom and IC202. and 21 of IC202? Check IC401 CKB5237L/7227L...
CH1 P-P = 720m V CH1 RMS = 2.602 V Check contrast circuit Replace the IC102 5.5 V (IC101 Pin #23) on the main Board (Q507 and Q511). Check DC 75 V at Pin 6 of IC102. CH1 P-P = 5.5 V CH1 RMS = 1.084 V CKB5237L/7227L...
Page 36
Does the OSD output Check IC102 CH1 P-P = 4.96 V CH1 RMS = 4.472 V signal appear at Pins 21, 22 and 23 of IC104? Check the pins of IC600 and the related circuit. OSD Gain (IC101 Pin 11) Check IC102 CKB5237L/7227L...
Page 37
6-9 Degauss Operation Failure When you push the manual degauss button, Replace IC202 does 5 V appear at Pin 3 of IC202? When pushing the manual degauss button, does the Q600 Replace Q600 operate well? Check and replace if necessary RL601. CKB5237L/7227L...
Active Active Green Stand-By Inactive Active Blank Green blinking (0.5sec) Suspend Active Inactive Blank Green blinking (1sec) Inactive Inactive Blank blinking (1sec) Note: If the signal cable is removed, DPMS function does not operate and a self raster displays. CKB5237L/7227L...
Page 39
6 Troubleshooting 6-11 User Controls Don’t Work Does the DC level change at Pins Check the button 13 and 14 of IC201 when you push (SW201 ~ SW203) the Main PCB? Check IC201, IC202 and RESET circuit. CKB5237L/7227L...
1. The secondary voltage is read with an SSVM from the indicated point to a cold ground ( The primary voltage is read with an SSVM from the indicated point to a hot ground ( 2. This schematic diagram is subject to change without notice. CKB5237L/7227L 11-1...