TABLE OF CONTENTS PAGE PAGE 1 Safety Precautions -----------------------------------------------3 1.1. General Guidelines ----------------------------------------3 1.2. Leakage Current Cold Check ---------------------------3 1.3. Leakage Current Hot Check (See Figure 1.)--------3 1.4. How to Discharge the Capacitor on Flash P.C.B.----------------------------------------------------------4 2 Warning --------------------------------------------------------------5 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices ----------5 2.2.
1 Safety Precautions 1.1. General Guidelines 1.3. Leakage Current Hot Check (See Figure 1.) 1. IMPORTANT SAFETY NOTICE There are special components used in this equipment 1. Plug the AC cord directly into the AC outlet. Do not use which are important for safety. These parts are marked by an isolation transformer for this check.
1.4. How to Discharge the Capacitor on Flash P.C.B. CAUTION: 1. Be sure to discharge the capacitor on FLASH P.C.B.. 2. Be careful of the high voltage circuit on FLASH P.C.B. when servicing. Before disassembling, perform "6.4. Forced full flash emission" for discharging capacitor. The capacitor also can be discharged according to the following procedures.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
2.3.2.3. How to Replace the Fuse A replacement fuse cover can be purchased from your local Panasonic Dealer. 1. Remove the Fuse Cover with a screwdriver. If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safety.
NOTE: This Lithium battery is a critical component. (Type No.: ML-614S/DN Manufactured by Energy Company, Panasonic Corporation) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in requirement designed specifically for its use.
When a part replacement is required for repairing MAIN P.C.B., replace as an assembled parts. (Main P.C.B.) 2. The following category is /are recycle module part. Please send it/them to Central Repair Center. • MAIN P.C.B. (VEP03J48B: HC-V700MP/PC/PU/GK, HC-V707MEG) • MAIN P.C.B. (VEP03J48C: HC-V700P/PC/EB/EC/EE/EF/EG/EP/GC/GK/GN, HC-V707EG)
3.4. How to Define the Model Suffix (NTSC or PAL model) There are eight kinds of HC-V700/V707/V700M/V707M. • a) HC-V700M, V600M (Japan domestic model) • b) HC-V700P, V700MP • c) HC-V700PC, V700MPC • d) HC-V700EB/EC/EF/EG/EP/GN • e) HC-V707EG, V707MEG • f) HC-V700EE •...
5 Location of Controls and Components Shoe adaptor release lever [SHOE ADAPTOR RELEASE] Intelligent auto/Manual button [iA/MANUAL] Optical image stabilizer button O.I.S.] USB terminal [ ] 1080/60p button [1080/60p] (NTSC areas) 1080/50p button [1080/50p] (PAL areas) Power button [ Battery release lever [BATT] AV MULTI HDMI mini connector [HDMI] AV multi connector [AV MULTI]...
Page 14
18 Shoe adaptor mount 18 19 20 [SHOE ADAPTOR] 19 Status indicator 20 Recording start/stop button 21 LCD monitor (Touch screen) It can open up to 90 . It can rotate up to 180 towards the lens or 90 towards the opposite direction. Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the LCD monitor screen.
Page 15
Selecting a mode Slide the mode switch to switch between recording and playback. Operate the mode switch to change the mode to Motion Picture Recording Mode Still Picture Recording Mode Playback Mode How to use the touch screen You can operate by directly touching the LCD monitor (touch screen) with your finger. Touch Touch and release the touch screen to select icon or picture.
About the Touch Menu Touch (left side)/ (right side) of on the Touch Menu to switch the operation icons. Touch (left side)/ (right side) of on the Touch Menu. It is also possible to switch the operation icons by sliding the Touch Menu right or left while touching it.
6 Service Mode 1. Indication method of the service menu Set the mode switch “Motion Picture Recording” mode. 2. While the power is turned OFF, keep pressing the “Power” button, “Zoom lever” to W side and “intelligent auto/Manual” button for more than 3 seconds until the top screen of the Service Mode Menu being displayed. Service mode menu Screen display Contents...
6.1. Built-in Memory Self Check Execution (HC-V700M/V707M only) Touch the [ 3 ] of LCD, select Built-in memory self check execution. Operation specifications Indication contents • Built-in memory self check result display Display the Built-in memory self check execution. Displays other than “OK” are abnormalities of Built-in memory. Touch the [ BAK ] of LCD to end the service mode, and then POWER OFF.
6.3. Power ON Self Check Result Display Touch the [ 5 ] of LCD, select Power ON self check result display. Operation specifications Indication contents • Power ON self check result display Function to diagnose correct function of the device and interface between devices result display. Display the following communication test result.
6.5. Erasing the lock histories Touch the [ 10 ] of LCD, select erasing the lock histories execution. Operation specifications Indication contents • Erasing the error histories stored in EEPROM. (working time is not erased) Cutting of battery connection or AC power supply connection to end the service mode. 6.6.
7 Service Fixture & Tools 7.1. When Replacing the Main P.C.B. After replacing the MAIN P.C.B., be sure to achieve adjustment. The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-AVC” web-site in “TSN system”, together with Maintenance software. 7.2.
Page 22
CAUTION-1. (When servicing FLASH P.C.B.) 1. Be sure to discharge the capacitor on FLASH P.C.B.. Refer to “HOW TO DISCHARGE THE CAPACITOR ON FLASH P.C.B.”. The capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed. 2.
8 Disassembly and Assembly Instructions 8.1. Disassembly Flow Chart for the Unit This is a disassembling chart. When assembling, perform this chart conversely. 8.2. PCB Location...
8.3. Disassembly Procedure for the Item Removal Monitor P.C.B. (Fig. D17) 1 Locking tab Unit 1 Hanging part Monitor P.C.B. MOS Unit (Fig. D18) 3 Screws (S) Item Removal IR Filter MOS Shield Case Unit Side Case-L Unit (Fig. D1) 2 Screws (A) Lens Sheet 1 Screws (B)
Page 25
8.3.1. Removal of the Side Case-L Unit (Fig. D1) (Fig. D2)
8.3.2. Removal of the Top Case Unit 8.3.3. Removal of the ESD P.C.B. Unit (HC-V700M/V707M only) (Fig. D4) 8.3.4. Removal of the Front Case Unit (Fig. D5) (Fig. D3)
9 Measurements and Adjustments 9.1. Electric Adjustment • Adjustment method is different from a conventional High definition video camera. • An exclusive jig and PC (including software for adjustment “Tatsujin”) are necessary for electric adjustment. • A USB driver for service is necessary to communication with PC. •...
Page 35
Adjustment Items • Adjustment item as follows. The adjustment instruction is available at "Software download" on the "Support Information from NWBG/VDBG-AVC" web-site in "TSN System".
10 Factory Setting 10.1. How To Turn On The Factory Settings? 1. Set the mode switch “Motion Picture Recording” mode. 2. While the power is turned OFF, keep pressing the “Power” button, “Zoom lever” to W side and “intelligent auto/Manual” button for more than 3 seconds until the top screen of the Service Mode Menu being displayed.
10.2. What Is The Factory Settings? The factory settings clean up and/or refresh the following settings. 1. MENU, MODE, ADJUSTMENT VALUE. 2. SD card format. 3. Reset the folder number and file number of still pictures. (Setting the folder number is 100, and file number is 0.) 4.
11 Block Diagram 11.1. Overall Block Diagram OVERALL BLOCK DIAGRAM NOTE : VIDEO SIGNAL : AUDIO SIGNAL : CLK or CONTROL LINE LENS(F1.8-3.5 21x) IC101 ZOOM/ COLOR LCD MOS IMAGE FOCUS PANEL IC901 IRIS SENSOR MOTOR/ DRIVER IC902 MAGNETIC SENSOR Analog IC102,302 IC706...
11.4. Video/Audio Signal Process(2) Circuit Block Diagram VIDEO/AUDIO SIGNAL PROCESS ( 2 ) CIRCUIT BLOCK DIAGRAM IC901 IC3701 (LCD COLOR DRIVER) (AVIO) LCD LVDS0P JK6002 (AV JACK) V OUT PROTOCOL PARSING, VOUT LCD LVDS0N PARITY DETECTION, HDY OUT ADVANCED DESERIALIZER Y IN HDYOUT LCD LVDS1P...
11.6. Power Supply Circuit Block Diagram POWER SUPPLY CIRCUIT BLOCK DIAGRAM Please check the Fuse Resistor when an output JK6401 IP6401 voltage does not output. FUSE RESISTOR: DC IN (R1001/R1261/R6409) R1001 CL1001 Q1501 PW STNOREG (To FLASH) CL1341 PW CAM1.2V CL1002 PW SENS1.8V CL1422...
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks C301 F1G0J1050007 C.CAPACITOR CH 6.3V 1U C302 F1L0J1040001 C.CAPACITOR CH 6.3V 0.1U C303 F1G0J1050007 C.CAPACITOR CH 6.3V 1U C304 F1G0J1050007 C.CAPACITOR CH 6.3V 1U C305 F1G1C104A077 C.CAPACITOR CH 16V 0.1U...
Page 66
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks C921 F1H1A105A036 C.CAPACITOR CH 10V 1U C922 F1H1A105A036 C.CAPACITOR CH 10V 1U C924 F1G1H220A644 C.CAPACITOR CH 50V 22P C925 F1G1H220A644 C.CAPACITOR CH 50V 22P C926 F1G1H220A644 C.CAPACITOR CH 50V 22P...
Page 67
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks C1522 F1L0J1040001 C.CAPACITOR CH 6.3V 0.1U C1523 F1L0J1040001 C.CAPACITOR CH 6.3V 0.1U C2301 F1L0J1040001 C.CAPACITOR CH 6.3V 0.1U C2304 F1L0J1040001 C.CAPACITOR CH 6.3V 0.1U C2305 F1L0J1040001 C.CAPACITOR CH 6.3V 0.1U...
Page 68
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks C3461 F1G0J1050007 C.CAPACITOR CH 6.3V 1U C3462 F1G0J1050007 C.CAPACITOR CH 6.3V 1U C3464 F1L0J1040001 C.CAPACITOR CH 6.3V 0.1U C3465 F1L0J1040001 C.CAPACITOR CH 6.3V 0.1U C3466 F1G0J1050007 C.CAPACITOR CH 6.3V 1U...
Page 69
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks C6421 F1G0J1050007 C.CAPACITOR CH 6.3V 1U 1 (MAIN P.C.B.) C6421 F1J1A106A043 C.CAPACITOR CH 10V 10U 1 (SD HOLDER P.C.B.) D901 DZ2J200M0L DIODE 1 E.S.D. D902 B3AFB0000426 DIODE...
Page 70
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks IC6411 L2ES00000038 1 E.S.D. IP1502 K5H402YA0080 IC PROTECTOR IP6401 K5H402YA0080 IC PROTECTOR JK6001 K2HC106E0009 JACK, A/V JK6002 K2HZ112E0001 JACK, AV MULTI JK6003 K1FA119E0020 JACK, HDMI JK6401 K2EBYB000003 JACK, DC JK6402 K2HZ105E0013...
Page 71
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks Q4902 DSA300100L TRANSISTOR 1 E.S.D. Q4903 DSC300100L TRANSISTOR 1 E.S.D. Q4904 DSA300100L TRANSISTOR 1 E.S.D. Q4907 DSC300100L TRANSISTOR 1 E.S.D. Q4908 DSC300100L TRANSISTOR 1 E.S.D. Q6421 DSC300100L TRANSISTOR...
Page 72
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks R913 ERJ2GEJ151 M.RESISTOR CH 1/10W 150 R914 ERJ2GEJ151 M.RESISTOR CH 1/10W 150 R915 ERJ2GEJ820 M.RESISTOR CH 1/16W 82 R1001 D1JBR102A006 FUSE RESISTOR R1101 ERJ2RKD124 M.RESISTOR CH 1/16W 120K R1107 ERJ1GEJ103...
Page 73
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks R3426 ERJ2RHD101 M.RESISTOR CH 1/16W 100 R3428 ERJ2RHD101 M.RESISTOR CH 1/16W 100 R3429 ERJ1GEJ273 M.RESISTOR CH 1/20W 27K R3430 ERJ2RHD431 M.RESISTOR CH 1/16W 430 R3431 ERJ2RHD272 M.RESISTOR CH 1/16W 2.7K...
Page 74
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks R4909 ERJ1GEJ102 M.RESISTOR CH 1/20W 1K R4910 ERJ1GEJ562 M.RESISTOR CH 1/20W 5.6K R4911 ERJ1GEJ151 M.RESISTOR CH 1/20W 150 R4912 ERJ1GEJ471 M.RESISTOR CH 1/20W 470 R4913 ERJ3RBD103 M.RESISTOR CH 1/10W 10K...
Page 75
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks VA6405 D4EDY1310001 VARISTOR X2303 H0J327200085 CRYSTAL OSCILLATOR X3402 H1A5405B0027 CRYSTAL OSCILLATOR...
Page 76
Model No. : HC-V700/V700M/V707/V707M Frame and Casing Section...
Page 77
Model No. : HC-V700/V700M/V707/V707M LCD Section...
Page 78
Model No. : HC-V700/V700M/V707/V707M Packing Parts and Accessories Section...
Page 79
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks VYK5L06 FRONT CASE UNIT 1 (-K) VYK5L17 FRONT CASE UNIT 1 (-S) VEP03J60C ESD P.C.B. UNIT(16GB) 1 V700MP,MPC,MPU,MGK, V707MEG VWJ2327 ECM RELAY FPC VGQ1D43 LENS SHEET VMP0C14 BATTERY FRAME...
Page 80
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks OPERATING INSTRUCTIONS (CHINESE(SIMPLIFI VQT3Y53 1 GK ED)) OPERATING INSTRUCTIONS (GERMAN/TURKISH/I VQT3Y44 1 EG TALIAN/DUTCH) VQT3Y45 OPERATING INSTRUCTIONS (FRENCH) 1 EG,EF OPERATING INSTRUCTIONS (SPANISH/PORTUGUE VQT3Y46 1 EC SE/SWEDISH/ DANISH/FINNISH) OPERATING INSTRUCTIONS (ENGLISH/POLISH/C...
Page 81
Model No. : HC-V700/V700M/V707/V707M Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks B202 VHD2072 SCREW B203 VHD2072 SCREW B204 VHD2072 SCREW B205 VHD2072 SCREW B206 VHD2072 SCREW B207 VHD2072 SCREW B208 VHD2072 SCREW...