Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DeWalt DCS381-XE
Summary of Contents for DeWalt DCS381-XE
- Page 1 INSTRUCTION MANUAL DCS380-XE, DCS381-XE 18 V CORDLESS RECIPROCATING SAWS...
-
Page 3: Definitions: Safety Guidelines
1) WORK AREA SAFETY Definitions: Safety Guidelines a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the The definitions below describe the level of severity for each signal presence of flammable liquids, gases or dust. -
Page 4: Electrical Safety
c) Prevent unintentional starting. Ensure the switch is in the off position g) Use the power tool, accessories and tool bits etc., in accordance with before plugging in. Carrying power tools with your finger on the switch or these instructions and in the manner intended for the particular type of plugging in power tools that have the switch on invites accidents. -
Page 5: Extension Cords
• Replacement of the supply cord. If the supply cord is damaged, it must be • Do not operate this tool for long periods of time. Vibration caused by the replaced by the manufacturer or an authorised D WALT Service Centre in order operating action of this tool may cause permanent injury to fingers, hands, and to avoid a hazard. -
Page 6: Important Safety Instructions For All Battery Packs
• Charge the battery packs only in designated D WALT chargers. CAUTION: When not in use, place tool on its side on a stable surface where it • DO NOT splash or immerse in water or other liquids. will not cause a tripping or falling hazard. Some tools with large battery packs will •... -
Page 7: Charging Procedure
• Contents of opened battery cells may cause respiratory irritation. Provide fresh • Do not use an extension cord unless it is absolutely necessary. Use air. If symptoms persist, seek medical attention. of improper extension cord could result in risk of fire, electric shock or electrocution. -
Page 8: Charge Indicators
3. The completion of charge will be indicated by the red light remaining ON battery pack elicits the same trouble indication as the original, have the charger and the continuously. The pack is fully charged and may be used at this time or left in the battery pack tested at an authorized service center. -
Page 9: Storage Recommendations
WARNING: Burn hazard. Do not submerge the battery pack in any liquid or allow any liquid to enter the battery pack. Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return to a service DCS381-XE center for recycling. Storage Recommendations 1. -
Page 10: Operation
COMPONENTS (FIG. 1, 2) OPERATION WARNING: Never modify the power tool or any part of it. Damage or personal WARNING: To reduce the risk of serious personal injury, turn tool off and injury could result. disconnect tool from power source before making any adjustments or removing/ installing attachments or accessories. - Page 11 Figure 7. The blade TO REMOVE BLADE FROM SAW can be installed in the DCS381-XE in two positions as shown in Figure 7. Both units allow the blade to CAUTION: Burn hazard. Do not touch the the blade immediately after use. Contact be installed upside-down to assist in flush-to cutting;...
- Page 12 Failure one of the three settings and release the button. to do so may result in explosion, property The DCS381-XE comes with a fixed shoe that is damage, electric shock, and/or serious not adjustable.
-
Page 13: Maintenance
POCKET/PLUNGE CUTTING – WOOD ONLY (FIG. 12) METAL CUTTING (FIG. 13) The initial step in pocket cutting is to measure the surface area to be cut and mark Your saw has different metal cutting capacities depending upon type of blade used clearly with a pencil, chalk or scriber. - Page 14 Cleaning WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To minimize the risk of eye injury, always wear AS/NZS51337 approved eye protection when performing this. WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool.
- Page 16 The battery voltage is nominal, it can measure above or below depending on the state of charge. Stanley Black & Decker 701 East Joppa Road, Baltimore, MD 21286 • 82 Taryn Drive, Epping, VIC 3076 Australia (MAR11) Part No. N111154 DCS380-XE, DCS381-XE Copyright © 2011 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...