Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt DCD720-XE
Summary of Contents for DeWalt DCD720-XE
- Page 1 INSTRUCTION MANUAL DCD720-XE CORDLESS RIGHT ANGLE DRILL/DRIVER...
-
Page 3: Definitions: Safety Guidelines
The vibration emission level given in this information sheet has been measured in Technical Data accordance with a standardised test given in EN 60745 and may be used to compare DCD720-XE one tool with another. It may be used for a preliminary assessment of exposure. Voltage 14.4... - Page 4 safety instructions before attempting to operate this product. Keep these instructions in e) When operating a power tool outdoors, use an extension cord suitable a safe place. for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
-
Page 5: Extension Cords
b) Do not use the power tool if the switch does not turn it on and off. Any 6) SERVICE power tool that cannot be controlled with the switch is dangerous and must a) Have your power tool serviced by a qualified repair person using only be repaired. -
Page 6: Important Safety Instructions For All Battery Packs
• Use clamps or other practical way to secure and support the workpiece to a exposed areas with soap and water. Allowing dust to get into your mouth, eyes, stable platform. Holding the work by hand or against your body is unstable and or lay on the skin may promote absorption of harmful chemicals. -
Page 7: Important Safety Instructions For All Battery Chargers
READ ALL INSTRUCTIONS SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion) • Do not incinerate the battery pack even if it is severely damaged or is • Do not charge or use the battery pack in explosive atmospheres, such as in the completely worn out. - Page 8 Charging Procedure (Fig. 1) • Do not expose the charger to rain or snow. • Pull by the plug rather than the cord when disconnecting the charger. This will 1. Plug the charger into an appropriate outlet before inserting the battery pack. reduce the risk of damage to the electric plug and cord.
-
Page 9: Charge Indicators
Charge Indicators 2. The charger and battery pack may become warm to the touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the This charger is designed to detect certain problems that can arise. Problems are cooling of the battery pack after use, avoid placing the charger or battery pack in indicated by the red light flashing at a fast rate. -
Page 10: Assembly And Adjustments
2. For long storage, it is recommended to store a fully charged battery pack in a INTENDED USE cool dry place out of the charger for optimal results. This drill is designed for professional drilling and screwdriving applications. NOTE: Battery packs should not be stored completely depleted of charge. The battery DO NOT use under wet conditions or in presence of flammable liquids or gases. -
Page 11: Operation
When changing the position of the control button, be sure the paddle is released. 3. Insert the bit or other accessory about 19 mm (3/4") into the chuck and tighten NOTE: The first time the tool is run after changing the direction of rotation, you may securely by holding the chuck and rotating in the clockwise direction. -
Page 12: Drill Operation
Installing and Removing the Battery Pack (Fig. 3) For more information regarding fuel gauge battery packs, please contact Stanley Black & Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call 1800 444 224 or (NZ). NOTE: For best results, make sure your battery pack is fully charged. 0800 339 258. -
Page 13: Maintenance
Cleaning 2. Use sharp drill bits only. 3. Always apply pressure in a straight line with the bit. Use enough pressure to keep WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once drill biting, but do not push hard enough to stall the motor or deflect the bit. - Page 16 Stanley Black & Decker 82 Taryn Drive, Epping, VIC 3076 Australia • 1800 444 224 (Aust) or 0800 339 258 (NZ) www.dewalt.com.au • www.dewalt.co.nz (JUN12) Part No. N189091 DCD720-XE Copyright © 2012 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...