Integrated digital full hd colour televisions (37 pages)
Summary of Contents for Beko V30
Page 2
? ? The part number of FBT is actually 058838(28”) and 058238(32”) in SPPL. So, if you order with those part number, Beko will deliver Eldor FBT automatically. « FILE THIS SERVICE BULLETIN WITH YOUR SERVICE MANUAL « I/C : INTERCHANGEABILITY CODE...
CONTENTS PAGE Safety Instructions Technical Specifications Pin Voltages of IC’s Pin Voltages of Some Transistors Oscillograms Electrical and Service Adjustments Trouble Shooting Guide Parts List Circuit Diagram PIP Module Circuit Diagrams Attached 27/05/2002, Version 2...
SAFETY INSTRUCTIONS GENERAL GUIDELINES connectors, control shafts etc. When the exposed metallic part a return path to the 1. It is advised to insert an isolation transformer chassis the reading should be between in the AC supply before servicing a hot 4Mohm 20Mohm.
TECHNICAL SPECIFICATIONS Power source: 220-240 VAC, 50-60Hz Power consumption (max.) 120 W 21” Pure Flat 125 W 25”, 28” Mono 145 W 25”, 28” 4/3, 29” Pure Flat 140 W 29” Super Flat 150 W 28” 16/9 Super Flat 155 W 28”...
Page 7
IC 301 (MSP 3400G) MULTI STANDARD SOUND PROCESSOR Connection V DC Connection V DC 1 Not connected 33 Scart 2 sound output (R) 2 Gnd 34 Scart 2 sound output (L) 3 Gnd 35 Reference analog ground 4 Digital control input/output 36 Scart 1 sound output (R) 5 Digital control input/output 37 Scart 1 sound output (L)
1. ELECTRICAL ADJUSTMENTS 1.1. Supply Voltage Adjustment Connect a digital voltmeter to the cathode of diode D611 at the AV1 mode of the TV and set the screen voltage to the minimum with the screen potentiometer. Adjust the main supply voltage (B+) with P601 potentiometer to the following value (after adjustment, readjust Screen voltage).
Page 14
2.2. Screen Adjustment Adjustment is change according to SW versions. New SW versions start from SB8643_A05, SB8643_B04, SB8643_C04, SB8643_D04, SB8645_A05, SB8645_B04, SB8645_C03 and SB8645_D04. • If CRT brand is Philips and SW is old version, then Set Brightness value to “00” in the Picture menu and store.
Page 15
TXT table : West (West Europe), East (East Europe), Cyrillic, Arabic, Hebrew, Greek A type SW includes East, West, Greek. B type SW includes East, West, Cyrillic, Arabic. C type SW includes East, West, Cyrillic, Hebrew. D type SW includes East, West, Cyrillic. Hotel : On (Hotel Mode), Off (TV Mode) Subwoofer...
Page 16
2.7 Software Versions During exit from service menu, the software version and feature options (hexadecimal number) are shown on the screen. For example: SB8643_X05, C697H. Stereo software versions of 14.2 are named as follows: SB8643_X.. for TDA9563 (intercarrier) SB8645_X.. for TDA9565 (QSS) Mono Software versions are named as follows: SC3325-X..
POWER SUPPLY DEFECTS (I) Note: 1. All values in the diagrams are for 230 VAC mains supply. 2. Before replacing T601, check following components: R640, R604, R605, R609, C615. 3. Burst type standby mode was designed (Fixed frequency is 21.5 kHz for standby and 38.8 kHz for normal operation) .
Page 18
POWER SUPPLY DEFECTS (II) No operation Stand-by Voltages OK Check 4.2 VDC at pin 6 of IC101 Check connection to R409 and R641 Switch on the TV set. Check voltage 0.05 V pin Check the voltage 3.3 V 6 of IC101 and 0.28 V at R439 at pins 59, 66 of IC101 and pin 8 of IC402 Check and replace IC101 POWER SUPPLY DEFECTS (III)
Page 19
POWER SUPPLY DEFECTS (IV) When TV is on, voltages 145V,15V,11.8V, 3.3V, 8V, 5V, 28V are not at their proper values +B voltage is around 160V instead of 145V. Check and replace T607, R625, R645, PH601, ZD602. +B voltage is 20-80V instead of 145V. There should be 14 VAC at R612 and 11.8 VDC at cathode of D614.
Page 20
PICTURE AND COLOUR DEFECTS No picture Raster OK Check the tuner pin voltages. Check the Check video out signal at pin 38 of IC101 voltage 3.6-4.6 V at pin 18, 19 of IC101. Check and replace F101, IC101. Check CVBS signal with an oscilloscope. The Only white raster visible on screen video signal goes through R103, T104, R154, F104, T105, C150 to pin 40 of IC101...
Page 21
HORIZONTAL DEFLECTION CIRCUIT DEFECTS Power supply voltages are OK. There is no high voltage Check 15V at the collector of T503. Check and replace R503 and TR501 Hor. Driver transformer Check the voltages 1.42 VDC and 0.92 VAC at Check voltage 8V at pin 9, 39 of IC101. If + pin of C502 present replace IC101.
Page 22
VERTİCAL DEFLECTION CIRCUIT DEFECTS There is a horizontal line on the screen Check and replace R127 (at pin 20 of IC101), Check 16 VDC at pin 3 of IC501. C126 (at pin 21 of IC101), R526, D513, C527, R521. Check 35 VDC at pin 6 of IC501. Flyback lines are visible.
Page 23
AUDIO DEFECTS (I) No sound. Picture is OK. Check 28 VDC at pin 9 of IC304. Check and replace components R341, D612, S603. Audio signal at pins 1,5 of IC304 are OK. Check signals at pins 8, 10 of IC304. No sound.