Sony CDX-C90 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Car Receiver
  5. CDX-C90 - Fm/am Compact Disc Player
  6. Service manual
Sony CDX-C90 Service Manual

Sony CDX-C90 Service Manual

Fm/am compact disc player
Hide thumbs Also See for CDX-C90:
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
Ver 1.1 2001. 08
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (US model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
19 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than
1 % total harmonic distortion.
Other specifications
CD player section
System
Compact disc digital audio
system
Signal-to-noise ratio
108 dB
Frequency response
5 - 20,000 Hz (±1 dB)
Wow and flutter
Below measurable limit
Laser Diode Properties
Material
GaAlAs
Wavelength
780 nm
Emission Duration
Continuous
Laser output power
Less than 44.6 µW*
* This output is the value measured at a distance of
200 mm from the objective lens surface on the Optical
Pick-up Block.
Tuner section
FM
Tuning range
FM tuning interval:
50 kHz/200 kHz switchable
87.5 - 108.0 MHz
(at 50 kHz step)
87.5 - 107.9 MHz
(at 200 kHz step)
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz
Usable sensitivity
8 dBf
Selectivity
75 dB at 400 kHz
50 dB at 200 kHz
Signal-to-noise ratio
65 dB (stereo),
68 dB (mono)
Harmonic distortion at 1 kHz
0.3% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
20 - 15,000 Hz (±0.5 dB)
Sony Corporation
9-925-982-12
2001H0400-1
e Vehicle Company
© 2001. 8
Shinagawa Tec Service Manual Production Group
CDX-C90
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
AM
Tuning range
AM tuning interval:
9 kHz/10 kHz switchable
531 - 1,602 kHz
(at 9 kHz step)
530 - 1,710 kHz
(at 10 kHz step)
Antenna terminal
External antenna connector
Intermediate frequency 10.71 MHz/450 kHz
Sensitivity
30 dBµV
General
Outputs
Digital output
Line outputs (3)
Power antenna relay
control lead
Power amplifier control
lead
Telephone ATT control
lead
Illumination control lead
Tone controls
Bass ±8 dB at 100 Hz
Treble ±8 dB at 10 kHz
Power requirements
12 V DC car battery
(negative ground)
FM/AM COMPACT DISC PLAYER
– 1 –
US Model
E Model
CDX-C680/C780
MG-363S-121
KSS-520A
– Continued on next page –

Advertisement

Table of Contents
loading

Related Manuals for Sony CDX-C90

Summary of Contents for Sony CDX-C90

  • Page 1 CDX-C90 SERVICE MANUAL US Model E Model Ver 1.1 2001. 08 Model Name Using Similar Mechanism CDX-C680/C780 SPECIFICATIONS CD Drive Mechanism Type MG-363S-121 Optical Pick-up Name KSS-520A AUDIO POWER SPECIFICATIONS (US model) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 19 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 1 % total harmonic distortion.
  • Page 2 COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS 1. GENERAL 3. ELECTRICAL ADJUSTMENTS Initial settings ................4 CD Section ................44 Setting the clock ..............5 Tuner Section ................. 44 Using the main panel controls ..........6 Basic oprations ................ 7 4. DIAGRAMS Using the rotary remote ............8 4-1.

  • Page 4: General

    SECTION 1 GENERAL This section is extracted from instruction manual. – 4 –...
  • Page 5 – 5 –...
  • Page 6 – 6 –...
  • Page 7 – 7 –...
  • Page 8 – 8 –...
  • Page 9 – 9 –...
  • Page 10 – 10 –...
  • Page 11 – 11 –...
  • Page 12 – 12 –...
  • Page 13 – 13 –...
  • Page 14 – 14 –...
  • Page 15 – 15 –...
  • Page 16 – 16 –...
  • Page 17 – 17 –...
  • Page 18 – 18 –...
  • Page 19 – 19 –...
  • Page 20 – 20 –...
  • Page 21 – 21 –...
  • Page 22 – 22 –...
  • Page 23 – 23 –...
  • Page 24 – 24 –...
  • Page 25 – 25 –...
  • Page 26 – 26 –...
  • Page 27 – 27 –...
  • Page 28 – 28 –...
  • Page 29 – 29 –...
  • Page 30 – 30 –...
  • Page 31 – 31 –...
  • Page 32 – 32 –...
  • Page 33 – 33 –...
  • Page 34 – 34 –...

  • Page 35: Disassembly

    SECTION 2 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 2-1. COVER (UPPER) 1 PTT 2.6x4 7 cover (upper) 6 claws 2-2. FRONT PANEL ASSY 3 front panel assy 1 Push the button (release). – 35 –...

  • Page 36: Cords

    2-3. CORDS 8 cord (with connector) (INVERTER) (EL transformer unit) 7 PTT 2.6x4 4 cord (with connector) (RCA) (BUS AUDIO IN, SUB OUT) 3 PTT 2.6x4 5 PTT 2.6x4 6 power cord 1 PTT 2.6x4 2 cord (with connector) (RCA) (FRONT LINE OUT, REAR LINE OUT) 2-4.

  • Page 37: Md Assy

    2-5. MD ASSY 7 MD assy 5 CN101 3 PTT 2.6x4 1 Slide the base panel in the direction of the arrow. 6 CN3 4 CN1 2 PTT 2.6x4 2-6. AUDIO BOARD 2 BVTT 2x4 3 AUDIO board 1 BVTT 2x4 –...

  • Page 38: Bracket (Md)

    2-7. BRACKET (MD) 3 bracket (MD) 2 PTT 2.6x4 5 COVER (MD) 1 PTT 2.6x4 4 PTT 2.6x4 2-8. MOTOR BLOCK 3 PTT 2.6x4 6 motor block 5 shaft 2 PTT 2.6x4 1 CN600 4 P 2X2.5 – 38 –...

  • Page 39: Base Panel Assy

    2-9. BASE PANEL ASSY FLEXIBLE board claws 1 step screw (M1.7) 5 CN300 2 step screw (M1.7) 6 base panel assy 2-10. SUB PANEL ASSY 1 B 2x4 3 PTT 2.6x4 2 B 2x4 4 sub panel assy – 39 –...

  • Page 40: Chassis (Front) Assy

    2-11. CHASSIS (FRONT) ASSY 1 ground point screw 8 shaft (pinion) assy 2 ground point screws 3 P 2x2.5 4 bracket (shaft pinion) 5 B 2.6x3 9 lever (L) assy 6 B 2.6x3 0 lever (R) assy 7 chassis (front) assy 2-12.

  • Page 41: Chassis (T) Sub Assy

    2-13. CHASSIS (T) SUB ASSY 1 P 2x3 2 P 2x3 3 chassis (T) sub assy 2-14. LEVER ASSY 5 guide (disc) 6 lever (R) assy 3 tension spring (LR) 7 lever (L) assy 1 PS 2x4 2 DISC IN SW board 4 claws –...

  • Page 42: Servo Board

    2-15. SERVO BOARD 2 PS 2x5 1 PS 2x5 3 heat sink 7 CN2 0 SERVO board 6 PS 2x4 4 CN4 5 CN5 8 P 2x3 9 loading motor assy 2-16. ROLLER ASSY • When installing, take note of the positions arm (roller) and washers.

  • Page 43: Chassis (Op) (O/S) Assy

    2-17. CHASSIS (OP) (O/S) ASSY 6 chassis (OP) (O/S) assy 8 compression spring (FL) 1 tension spring (angle) 7 compression spring (FL) 4 Fit lever (D) in the direction of the arrow. 5 Turn loading ring in the direction of the arrow. 3 damper (T) 2 damper (T) 2-18.

  • Page 44: Electrical Adjustments

    SECTION 3 ELECTRICAL ADJUSTMENTS CD SECTION FM Auto Scan/Stop Level Adjustment Setting : CD section adjustments are done automatically in this set. SOURCE button : FM 0 dB = 1 µV TUNER SECTION FM RF signal Cautions during repair generator When the tuner unit is defective, replace it by a new one antenna terminal...
  • Page 45 Ver 1.1 FM Stereo Separation Adjustment (WIDE) FM Stereo Separation Adjustment (NARROW) Setting : Setting : SOURCE button : FM SOURCE button : FM FM RF signal FM RF signal generator generator level meter level meter antenna antenna terminal 10 k Ω terminal 10 k Ω...
  • Page 46 AM Auto Scan/Stop Level Adjustment Adjustment Location : tuner unit (TU701) Setting : SOURCE n MODE button : AM –set upper view– 30 Ω 15 pF 65 pF AM RF signal generator AM dummy antenna (50 Ω ) TU701 antenna AM AUTO SCAN/ terminal Carrier frequency : 1000 kHz...

  • Page 47: Diagrams

    SECTION 4 DIAGRAMS 4-1. IC PIN DESCRIPTIONS • IC5 CXP84640-011Q (CD SYSTEM CONTROL) Pin No. Pin Name Pin Description 1 – 5 — Not used in this set. FP OPEN Front panel open detection input FP CLOSE Front panel close control output LINKOFF Bus interface link input (Not used in this set.) DRV OE...
  • Page 48 Pin No. Pin Name Pin Description BU.IN Back-up power detection input BUSON Bus on control input IN SW Disc in switch input (SW1) SELF SW Self switch input (SW2) TX CE EEPROM chip enable output SCK2 Sub Q read clock output Sub Q 80 bit, PCM peak and level data 16 bit input CD DATA CD signal process serial data output...
  • Page 49 • IC501 CXD2548R (DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) Pin No. Pin Name Pin Description SYSM System mute input (Not used.) RMUT1 R-ch, “0” detection output. (“H” : ON, “L” : OFF) (Not used.) LMUT2 L-ch, “0” detection output. (“H” : ON, “L” : OFF) (Not used.) CKOUT Master clock frequency division output (Not used.) VDD0...
  • Page 50 Pin No. Pin Name Pin Description ASY.O EFM full-swing output (“L” : VSS, “H” : VDD) Center voltage input Focus error signal input Sled error signal input Tracking error signal input Center error signal input RFDC RF signal input Condenser connection pin for LPF time constant of RF signal. ADIO OP amplifier output (Not used.) AVSS3...
  • Page 51 Pin No. Pin Name Pin Description ROUT2 R-ch, LINE output. (Not used.) AIN2 R-ch, OP amplifier input. (Not used.) AOUT2 R-ch, Analog output. (Not used.) AVDD2 — R-ch, Analog power supply. AVSS2 — R-ch, Analog GND. VSS0 — Digital GND –...
  • Page 52 • IC300 MB90F574PFV-G-139-BND (SYSTEM CONTROL) Pin No. Pin Name Pin Description TIR WR TIR IC data write output (Not used in this set.) TIR RD TIR IC data read output (Not used in this set.) TIR CE TIR IC data chip enable output (Not used in this set.) TIR CE XTIR IC data chip enable output (Not used in this set.) TIR BUSY...
  • Page 53 Pin No. Pin Name Pin Description — Power supply pin (+5 V) RAMBU RAM reset detection input TESTIN Test mode setting detection input AD ON Power control output of A/D conversion. 58, 59 RE IN0, 1 Rotary encoder input 0, 1 BOOT Compulsory boot mode input DIMMER...
  • Page 54 Pin No. Pin Name Pin Description SEEKOUT SEEK OUT output AM STIN AM stereo input (Not used in this set.) FM STIN Used in conjunction with stereo input/monaural output (FM mode) SD IN Signal detector input TU ATT Tuner mute output (Not used in this set.) TIR D0 TIR IC data 0 input/output (Not used in this set.) TIR D1...
  • Page 55 • IC500 HD6413002F16 (DISPLAY CONTROL) Pin No. Pin Name Pin Description — Power supply pin (+5 V) SIRCS Remote commander input SIRCS Remote commander input LCD-RST LCD controller reset control output ILL ON LCD controller power supply control output EL ON LCD back light EL power supply control output LCD-ST LCD controller information start request signal output...
  • Page 56 Pin No. Pin Name Pin Description DEC-INT Demodulator LSI initial output (Not used in this set.) ROM-CS PROM chip enable output — UNI-REQ Not used. LINK-OFF BUS interface link output DEC-ON Not used. DEC-CLR Demodulator LSI reset output (Not used in this set.) 97 –...

  • Page 57: Block Diagram -Cd Section

    CDX-C90 4-2. BLOCK DIAGRAM — CD SECTION — DRAM CONTROLLER DIGITAL SERVO/ MD 5V OPTICAL PICK-UP RF AMP, LD-APC ERROR AMP DIGITAL SIGNAL PROCESSOR (DIGITAL OUT) DIGITAL FILTER L.P.F KSS-520A D/A CONVERTER DOUT IC501 MAIN DATA 3 PD1 59 RFDC...

  • Page 58: Block Diagram -Main Section

    CDX-C90 4-3. BLOCK DIAGRAM — MAIN SECTION — INPUT SELECT/TONE/SUB VOLUME IC102 TUNER UNIT CN103 (1/2) L-CH ELECTRONIC VOLUME TU701 BUS AUDIO IC107(1/2) IC104 IC771 CN105 (ANTENNA) R-CH R-CH L-CH AM-ANT L-OUT FRONT FM-ANT LINE OUT R-OUT R-CH R-CH R-CH...

  • Page 59: Block Diagram -Display Section

    CDX-C90 4-4. BLOCK DIAGRAM — DISPLAY SECTION — SYSTEM CONTROL DISPLAY CONTROL DISPLAY SRAM IC300(2/2) CNJ301 IC500 IC504 (BUS CONTROL IN) SIRCS SRAM-CS KEYIN0 LINK-OFF KEYIN1 SRAM RESET Q309 S1–19,S1A,LSW1 SIRCS IC301 CONTROL KEY DET D300,301 Q308 RAMBU BU 5V...
  • Page 66 • IC Block Diagrams IC1 CXA1791N-T4 (SERVO BOARD) IC6 LB1638MTP-T1 N.C. VREF LD AMP PD AMP 1.25V OUT1 20 VCC – – 19 APC ON OUT2 18 RFI – – 17 RFO N.C. SUMMING AMP IV AMP1 – – 16 FE FOCUS IC551 LC89170M-TLM IV AMP2...
  • Page 67 IC4 MB814400C-70PFTN (SERVO BOARD) IC601 BA6195FP-YT2 25 24 23 22 21 16 15 THERMAL SHUT DOWN WRITE DRIVER DATA INPUT DATA OUTPUT CLOCK MUTE BUFFER BUFFER GENERATOR LEVEL SHIFT – – – CLOCK GENERATOR 4M BIT SENSE AMP COLUMN MEMORY DECODER I/O GATE CELL...
  • Page 68 IC1 CXD8679Q (MAIN BOARD) TIMING CIRCUIT IF SELD S / P INAF "0" DETECT IF SELC OVFLAG MUTE CIRCUIT MUTER SBCKI MUTEL MODE 4BIT DATA 3rd order L . I . P. NOISE MTPOL SDATAR SHAPER BITSTREAM x 0.75 SDATAL DRPOL DITHER MODE...
  • Page 69 IC102 CXA1946BR IC302 BA8270F-E2 BUS ON BUS ON SWITCH 35 34 30 29 28 27 26 RESET SWITCH 24 FNTO1 VOLUME VOLUME BUS ON LOUD TONE FADER 8dB STEP 1dB STEP 23 REO1 CLK IN BATTERY GAIN12 BATT BU IN SWITCH VCTBUFF GAIN11...
  • Page 70 IC721 BU2624FV-E2 IC600 BA6285FP-E2 XOUT PHASE VREF REFERENCE DIVIDER FMIN MAIN PRESCALER CONTROL COUNT DRIVER DRIVER SHIFT REGISTER LATCH AMIN IF COUNT 20BIT COUNT IFIN IC851 TA2051FN(EL) 24 23 22 21 20 14 13 NOISE FILTER NOISE SOM1 GATE SOM2 MAIN GATE GATE...

  • Page 71: Exploded Views

    SECTION 5 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by number in the exploded views are not supplied. Example : mark ! or dotted line with mark. • Items marked “*” are not stocked since KNOB, BALANCE (WHITE) ...

  • Page 72: Front Panel Section

    5-2. FRONT PANEL SECTION Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-025-811-01 BUTTON (SOURCE) 1-669-127-11 FLEXIBLE SW BOARD 3-025-820-01 FRAME (FRONT), ORNAMENT 3-025-807-01 PANEL, FRONT BACK 3-025-793-01 KNOB (VOL) 3-026-389-01 COVER (SOURCE) 3-025-815-01 LEVER (SEEK/AMS) 3-025-810-01 SHEET (FRONT), ADHESIVE 3-025-808-01 PLATE (SEEK/AMS), LIGHT GUIDE X-3375-934-1 PANEL SUB ASSY, FRONT (US)

  • Page 73: Chassis Section

    5-3. CHASSIS SECTION supplied TU701 supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3375-552-1 PANEL ASSY, SUB * 114 A-3313-956-A MAIN BOARD, COMPLETE (US) X-3375-555-1 PANEL ASSY, BASE * 114 A-3317-107-A MAIN BOARD, COMPLETE (E) 3-934-758-01 SPRING (A) * 115 X-3376-177-1 BRACKET (TRANSISTOR) ASSY...

  • Page 74: Cd Mechanism Section (1)

    5-4. CD MECHANISM SECTION (1) (MG-363S-121) M903 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 151 1-659-836-11 DISC IN SW BOARD 3-931-902-04 ARM (ROLLER) * 152 A-3291-816-B CHASSIS (T) SUB ASSY 3-936-756-01 ROLLER (D) 3-931-909-01 SPRING (LR), TENSION 3-321-393-01 WASHER, STOPPER X-3371-501-1 LEVER (L) ASSY...

  • Page 75: Cd Mechanism Section (2)

    5-5. CD MECHANISM SECTION (2) (MG-363S-121) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-931-914-01 SPRING (ANGLE), TENSION 3-931-893-01 ARM, CHUCKING * 209 A-3291-677-G CHASSIS (M) ASSY 3-931-897-01 DAMPER (T) 3-931-883-01 SPRING (TR), TENSION 3-931-879-02 LEVER (D) 3-931-881-01 LEVER (LOCK) * 204 3-913-404-11 RETAINER (DISC)

  • Page 76: Cd Mechanism Section (3)

    5-6. CD MECHANISM SECTION (3) (MG-363S-121) M901 M902 The components identified by mark ! or dotted line with mark. ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 251...

  • Page 77: Electrical Parts List

    SECTION 6 AUDIO ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by the parts list may be different from the they are seldom required for routine service. mark ! or dotted line with mark.
  • Page 78 AUDIO DISC IN SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > R146 1-260-008-11 CARBON MELF 1/8W R147 1-216-033-00 METAL CHIP 1/10W Q101 8-729-921-25 TRANSISTOR FMC2 R148 1-216-033-00 METAL CHIP 1/10W Q102 8-729-920-21 TRANSISTOR DTC314TKH04 R149 1-259-987-11 CARBON MELF 1/8W...
  • Page 79 MAIN LIMIT SW LOAD SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > A-3313-956-A MAIN BOARD, COMPLETE (US) A-3317-107-A MAIN BOARD, COMPLETE (E) D550 8-719-978-24 DIODE DTZ-TT11-5.6A ********************* D551 8-719-977-21 DIODE DTZ8.2C D552 8-719-988-62 DIODE 1SS355 X-3376-177-1 BRACKET (TRANSISTOR) ASSY D553...
  • Page 80 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-115-339-11 CERAMIC CHIP 0.1uF C412 1-163-263-11 CERAMIC CHIP 330PF 1-124-910-11 ELECT 47uF C413 1-115-866-11 ELECT 4.7uF 1-115-339-11 CERAMIC CHIP 0.1uF C415 1-124-703-11 ELECT 2200uF 1-115-339-11 CERAMIC CHIP 0.1uF C417 1-104-951-11 ELECT...
  • Page 81 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C779 1-163-037-11 CERAMIC CHIP 0.022uF * CN400 1-506-999-11 PIN, CONNECTOR (PC BOARD) 3P C781 1-135-091-00 TANTALUM CHIP 1uF * CN401 1-506-986-11 PIN, CONNECTOR (PC BOARD) 4P C784 1-128-436-11 ELECT * CN402 1-506-984-11 PIN, CONNECTOR (PC BOARD) 2P...
  • Page 82 Ver 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D424 8-719-914-43 DIODE DAN202K IC601 8-759-981-69 IC LM2904M D600 8-719-914-43 DIODE DAN202K IC602 8-759-363-82 IC PQ09TZ1U D604 8-719-988-62 DIODE 1SS355 IC721 8-759-448-85 IC BU2624FV-E2 D605 8-719-988-62 DIODE 1SS355 IC771 8-759-064-92 IC NJM5532M-D...
  • Page 83 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q415 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R300 1-216-821-11 METAL CHIP 1/16W Q416 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R301 1-216-821-11 METAL CHIP 1/16W Q417 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R302 1-216-821-11 METAL CHIP 1/16W Q601 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R309...
  • Page 84 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R366 1-216-037-00 METAL CHIP 1/10W R520 1-216-295-00 SHORT R371 1-216-049-11 RES,CHIP 1/10W R521 1-216-845-11 METAL CHIP 100K 1/16W R372 1-216-049-11 RES,CHIP 1/10W R522 1-216-817-11 METAL CHIP 1/16W R373 1-216-023-00 METAL CHIP 1/10W...
  • Page 85 MAIN SENSOR SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R782 1-216-208-00 RES,CHIP 2.7K 1/8W RB514 1-216-182-00 RES, CHIP NETWORK 220 (3216) RB515 1-216-182-00 RES, CHIP NETWORK 220 (3216) R782 1-216-210-00 RES,CHIP 3.3K 1/8W (US) <...
  • Page 86 SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C107 1-115-581-11 TANTAL. CHIP 100uF 8-752-374-12 IC CXD2522R-T6 C108 1-164-004-11 CERAMIC CHIP 0.1uF 8-759-427-15 IC MB814400C-70PFTN C109 1-115-581-11 TANTAL. CHIP 100uF 8-752-889-54 IC CXP84640-011Q C110 1-163-251-11 CERAMIC CHIP 100PF 8-759-823-87 IC LB1638M C111...
  • Page 87 SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R302 1-216-037-00 METAL CHIP 1/10W R604 1-216-097-00 RES,CHIP 100K 1/10W R303 1-216-308-00 METAL CHIP 1/10W R605 1-216-081-00 METAL CHIP 1/10W R304 1-216-683-11 METAL CHIP 0.5% 1/10W R305 1-216-675-11 METAL CHIP 0.5% 1/10W...
  • Page 88 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark PARTS FOR INSTALLATION AND CONNECTIONS *************** HARDWARE LIST *************************************** *************** 3-009-613-21 FRAME 7-685-851-04 SCREW +BVTT 2X4 (S) 3-025-812-01 COLLAR (90) 7-685-792-09 SCREW +PTT 2.6X6 (S) 3-027-138-01 SPRING, FITTING 7-685-105-19 SCREW +P 2X8 TYPE2 NON-SLIT 3-934-325-01 SCREW, +K (5X8) TAPPING 7-685-790-09 SCREW +PTT 2.6X4 (S)
  • Page 89 CDX-C90 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2001. 08 The CORRECTION-1, 2 are included into Ver 1.1...

Table of Contents