Related Manuals for JVC Everio GZ-HM400
Summary of Contents for JVC Everio GZ-HM400
- Page 1 HD MEMORY CAMERA GZ-HM400 INSTRUCTIONS To view the INSTRUCTIONS, click below. Z page 1 - 44 Advanced INSTRUCTIONS To view the Advanced INSTRUCTIONS, click below. Z page 45 - 94 GUIDEBOOK...
- Page 2 2 and 3 to ensure safe use of this product. For Future Reference: Enter the Model No. (located on the bottom of the camcorder) and Serial No. (located on the battery pack mount of the camcorder) below. Model No.
-
Page 3: Safety Precautions
It could tip over, causing serious damage to the camcorder. CAUTION! Connecting cables (Audio/Video, S-Video, etc.) to the camcorder and leaving it on top of the TV is not recommended, as tripping on the cables will cause the camcorder to fall, resulting in damage. CAUTION: The mains plug shall remain readily operable. - Page 4 If this symbol is shown, it is only valid in the European Union. Remember that this camcorder is intended for private consumer use only. Any commercial use without proper permission is prohibited. (Even if you record an event such...
-
Page 5: Charge The Battery Before Recording
The battery pack is not charged at the time of purchase. CAUTION Fire or injury may result if batteries NOT approved by JVC are used. Only use the batteries specified on page 41. Power/charge lamp blinks: Charging goes out: Charging finished... -
Page 6: The Camcorder
Date/Time Setting Open the LCD monitor to turn on the camcorder Power button LCD monitor Select [YES] within 10 seconds Slide your finger up and down on the sensor. Then touch OK. • When the message disappears, press the power button for at least 2 seconds to turn off the power, and then press it again for at least 2 seconds. -
Page 7: Video Recording
Video recording CAUTION Before recording an important scene, it is recommended to conduct a trial recording. Slide the mode switch to select Select recording mode (REC) The mode changes when you press the button. Start recording Press the START/STOP button to start recording, and press it again to stop. -
Page 8: Playing Back
Playing back Select playback mode (PLAY) The mode changes when you press the button. Select the desired file Select (Touch OK) To perform operations such as forward search or reverse search (Z p. 22) To view files on TV (Z p. 24) ... -
Page 9: Table Of Contents
® ® http://www.adobe.com/ NOTE Select your desired language with a single click. The model name is indicated on the bottom of your camcorder. USING WITH TV Viewing Files on TV ... 24 Connection with TV... 24 Playback Operation ... 25 COPYING Copying Files ... -
Page 10: Read This First
Make a backup of important recorded data It is recommended to copy your important recorded data to a DVD or other recording media for storage. JVC will not be responsible for any lost data. Make a trial recording Before the actual recording of important data,... -
Page 11: Getting Started
GETTING STARTED Accessories AP-V21U AC Adapter Battery Pack Component Cable LY37115-001A USB Cable Shoe Adapter RM-V751U Remote Control Lithium Battery Pre-installed in the remote control. CD-ROM NOTE Make sure to use the provided cables for connections. Do not use any other cables. Shoe Adapter An optional microphone or light can be attached to the shoe adapter. -
Page 12: Preparing The Remote Control
Attaching the Core Filter to the USB Cable The core filter reduces interference caused when connecting to other devices. Connect the end of the cable with the core filter to the camcorder. Release the stopper. 3 cm (1-3/16") To be connected to the camcorder Wind once. -
Page 13: Index
Index NOTE • Be careful not to cover 2, 3, 5, and C during shooting. • The LCD monitor can rotate 270°. -
Page 14: Tripod Mounting
« Index Screen Date Index Screen Tripod Mounting Align the camcorder stud hole with the tripod stud, and the mounting socket with the screw, and then rotate the camcorder clockwise to mount it to the tripod. NOTE Do not use a tripod on unsteady or unlevel surfaces. -
Page 15: Indications On Lcd Monitor
Indications on LCD Monitor During both Video and Still Image Recording D E C . 2 4 . 2 0 0 9 ! Selected Recording Mode Indicator (Z p. 19, 20) @ : Auto Mode : Manual Mode # Scene Select Indicator $ Effect Mode Indicator % White Balance Indicator &... - Page 16 During Video Playback D E C . 2 4 . 2 0 0 9 ! Mode Indicator # High Speed Recording Indicator $ Playlist Playback Indicator (Appears when playing back a playlist.) % Quick Review Indicator (Z p. 19) : Digest Playback Indicator &...
-
Page 17: Necessary Settings Before Use
See page 21. To detach the battery pack NOTE • You can also use the camcorder with just the AC adapter. • The actual recording time may shorten depending on the recording environment, such as when recording scenes with fast moving subject. -
Page 18: Language Setting
Select the desired language. To return to the previous screen Select To quit the screen Select [QUIT]. Grip Adjustment NOTE • Fasten the strap when you grip the camcorder. • When carrying the camcorder, please be careful not to drop it. -
Page 19: Other Settings
• It is recommended to use Class 6 when recording video in UXP mode. NOTE No SD card is supplied with your camcorder. Insert an SD card Preparation: Press the < (Power) button for more than 2 seconds to turn off the camcorder. -
Page 20: Recording/Playback
The video recording mode is automatically selected when you turn off the camcorder and then turn on again. • If the camcorder is not operated for 5 minutes while the power is on, it turns itself off automatically to conserve power. Approximate remaining... -
Page 21: Still Image Recording
Press SNAPSHOT fully to take a still image. NOTE • If the camcorder is not operated for 5 minutes while the power is on, it turns itself off automatically to conserve power. • The sides of still images recorded in 16:9 size may be cut off when printed. -
Page 22: Zooming
Zooming Preparation: • Select mode. • Select the recording mode. Zoom in T: Telephoto You can also zoom out/zoom in by selecting [W] or [T] on the LCD monitor. (On-screen zoom control) Zoom ratio (factory-preset) mode [10X/OPTICAL] [10X/OPTICAL] To change the maximum zoom ratio ... -
Page 23: Playing Back Files
Playing Back Files Video Playback Slide the mode switch to select (video) mode. To move to the previous or next page Touch [ ] or [ ] for over a second. To play back a few seconds from the ... -
Page 24: Still Image Playback
Still Image Playback Slide the mode switch to select (still image) mode. To move to the previous or next page Touch [ ] or [ ] for over a second. To delete a still image Select To change the number of thumbnails ... -
Page 25: Viewing Files On Tv
USING WITH TV Viewing Files on TV This camcorder is designed to be used with high-definition or NTSC-type color television signals. It cannot be used with a television of a different standard. Connection with TV You can output videos from the HDMI connector, COMPONENT connector, or AV connector. -
Page 26: Playback Operation
Playback Operation AV Connector After the connection with TV is completed Turn on the camcorder and the TV. Set the TV to its VIDEO mode. (Only when connecting the camcorder to the VCR/DVD recorder) -
Page 27: Copying
VCR/DVD recorder. NOTE • It is recommended to use the JVC DVD burner CU-VD50 or CU-VD3. If you use CU-VD20 or CU-VD40, the recording time may take approx. 2 times longer than the time that is described in the instruction manual of DVD burner. - Page 28 DVD burner. • When connecting to a BD burner, use a USB cable with Mini-A(Male) to B(Male) connectors. JVC’s QAM0852-001 (optional) is recommended. Refer to page 35 for information on contacting JVC. Backup All Files Preparation: •...
-
Page 29: Dubbing Files To A Vcr/Dvd Recorder
1) Select [QUIT]. 2) When [QUIT?] appears, select [YES]. NOTE This method can be used to copy video files to discs in a computer connected to the camcorder. Dubbing Files to a VCR/DVD Recorder Preparation: • Create a playlist. -
Page 30: Pc Operation
PC OPERATION Creating a Disc Using a PC You can copy the data from the camcorder and create a disc using a PC. Installing the software to the PC System Requirements Windows Vista Windows Vista ® Home Basic (SP1) Home Premium (SP1) - Page 31 Make sure that enough free space is left in the PC’s HDD. • Press the < (Power) button for more than 2 seconds to turn off the camcorder. USB Connector Power button USB Cable Press the < (Power) button for more than 2 seconds to turn on the camcorder.
- Page 32 Making User Lists to Arrange the Files You can make a user list of a certain subject (such as Travel, Athletic meet) and put the files related to the subject into the user list. Preparation: Make backup on the PC. Double-click the icon to open the calendar.
- Page 33 Creating a Disc Using a PC Copying Files to a disc Everio MediaBrowser supports 3 disc formats. Select the one that suits your purpose. DVD-Video Suitable if you will give the disc disc: to your friends and relatives. AVCHD disc: Suitable for high quality video. Suitable for high quality video with long recording time.
- Page 34 5) Copy files to any folder on the PC (such as the desktop). To edit files Use the software compatible with AVCHD/JPEG. NOTE Do not move or delete the folders and the files in the camcorder. Contains the still image folders. Video files with defective management information are saved.
-
Page 35: Using With A Portable Media Player
Preparation: Install iTunes on a PC. ® http://www.apple.com/itunes/ Connect the camcorder to the PC with the USB cable. Select [EXPORT TO LIBRARY]. All the files with the export setting turned on are transferred to PC. If you cannot export the file to iTunes ... -
Page 36: Uploading Files To Websites
Use of this software is authorized according to the terms of the software license. When contacting the nearest JVC office or agency in your country (refer to the JVC Worldwide Service Network at http://www.jvc-victor.co.jp/english/worldmap/index-e.html) about this software, please have the following information ready. -
Page 37: Further Information
Before requesting service, consult the following chart. If the solutions indicated in the chart do not solve the problem, consult your nearest JVC dealer or JVC service center for instructions. Refer also to the FAQ of new products on JVC’s website. - Page 38 If a malfunction occurs in the built-in memory ! P erform [FORMAT BUILT-IN MEM.]. (All data is deleted.) # If this does not solve the problem, contact the JVC customer service for repairs. To reset the camcorder when it does not operate normally ...
-
Page 39: Warning Indications
Set the clock. If the message still appears after setting the clock, the battery for the clock has been depleted. Consult your nearest JVC dealer. • Be sure to use JVC battery packs. • Set [REC MEDIA FOR VIDEO] to [BUILT-IN MEMORY]. •... -
Page 40: Specifications
Specifications General Power supply DC 11 V (Using AC adapter) DC 7.2 V (Using battery pack) Power consumption Approx. 4.0 W* * When the monitor backlight is set to [STANDARD] mode. Rated Current Consumption: 1A Dimensions (W x H x D) 67 mm x 72 mm x 135 mm (2-11/16"... - Page 41 Specifications Approximate recordable time (for video) Recording medium Quality Approximate number of images (for still image) Recording medium Image size/Quality 3456 x 1944 / FINE 3456 x 1944 / STANDARD 3072 x 1728 / FINE 3072 x 1728 / STANDARD 2592 x 1456 / FINE 2592 x 1456 / STANDARD 1920 x 1080 / FINE...
- Page 42 Required charging/recording time (approx.) Battery pack BN-VF808U BN-VF815U (Provided) BN-VF823U * When the monitor backlight is set to [STANDARD] mode. Charging time 1 h 50 m 2 h 40 m 3 h 40 m h: hour/m: minute Recording time 1 h 10 m* 2 h 25 m* 3 h 40 m*...
-
Page 43: Cautions
LCD Monitor • To prevent damage to the LCD monitor, DO ... push it strongly or apply any shocks..place the camcorder with LCD monitor on the bottom. • To prolong service life ... avoid rubbing it with coarse cloth. - Page 44 Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
-
Page 45: Terms
Terms AC Adapter ...16, 42 AV Connection ...25, 28 Battery Pack ...16, 42 BD/DVD Backup ...26 BD/DVD Burner ...26 CD-ROM ...10, 29 Clock Adjust ...16 Component Connection ...24 Copying Files ...26 Date/Time Setting ...5 Digest Playback ...22 Dubbing Playback ...28 Export to Library Mode ...34 Flash ...21 HDMI ...24... - Page 46 Advanced INSTRUCTIONS HD MEMORY CAMERA GZ-HM400...
- Page 47 Upload Trimming ... 75 Operating in Conjunction with TV via HDMI ... 76 FURTHER INFORMATION Changing the Menu Settings ... 77 Troubleshooting ... 86 Cleaning ... 89 Warning Indications ... 90 JVC Software License Agreement ... 92 Terms ... 94...
-
Page 48: Recording/Playback
Manual Recording Manual recording mode enables you to set the focus and screen brightness, etc. manually. Changing to Manual Recording Mode Preparation: • Select mode. • Select the recording mode. Select [A/M] twice. To return to the auto recording mode ... -
Page 49: Aperture Priority Setting
Manual Recording Aperture Priority Setting You can add a blurring effect to the background by setting the aperture value (F-number). Press A (Aperture Priority Setting). Turn the adjustment dial to select one of the following aperture value. At the lower F-number (larger aperture value), the background will be more blurred. -
Page 50: Manual Setting In Menu
Manual Setting in Menu In the manual recording mode: Touch MENU. Select [MANUAL SETTING]. Select the desired menu. Menus SCENE SELECT Adjusts the exposure and/or shutter speed to suit your surroundings or the subject. FOCUS ASSIST Assists you to adjust the focus. - Page 51 @ [AUTO]: White balance is adjusted automatically. MWB: Adjusts the white balance manually depending on the light source. 1) Hold a sheet of plain white paper in front of the camcorder so that the white paper fills the screen. 2) Keep touching OK until the appears.
-
Page 52: High Speed Recording
Menus > ZEBRA The over-exposed sections of the subject are displayed in striped pattern on the screen. Use this as a guide for adjusting the brightness. mode only) SHARPNESS Enhances the outline of the subject. mode only) High Speed Recording You can capture fast-moving subjects clearly. -
Page 53: Advanced Recording Functions
Turning on the Face Detection Mode If you set this mode on, the camcorder detects the faces and adjust brightness and focus so that the faces are recorded clearly. The maximum of 16 face frames are displayed. -
Page 54: Advanced Playback Functions
Advanced Playback Functions Playback with Special Effects Wipe or fader effects Add effects at the beginning and end of videos. These effects cannot be set for still images. Preparation: • Select mode. • Select the playback mode. Touch MENU. Select [WIPE/FADER]. Select a desired effect. -
Page 55: File Search Function
Advanced Playback Functions File Search Function Preparation: • Select mode. • Select the playback mode. Group Index Screen You can search the desired file by the group. The group is created automatically based on recording date and time. And the contents of the group are changed when adding/deleting or editing scenes. -
Page 56: Playing Back Mts Files
Event Screen You can search the desired file by the event that you registered the file to when recording. (Z p. 52) After searching by the event, you can search by the recording date to narrow down the search. Select Select [SEARCH EVENT]. -
Page 57: Editing
Managing Files CAUTION Do not remove the recording medium or perform any other operation (such as turning off the power) while accessing files. Also, be sure to use the provided AC adapter, as the data on the recording medium may be corrupted if the battery becomes exhausted during operation. -
Page 58: Protecting Files
Deleting Selected Files After performing steps 1-2 (Z p. 56) Select [FILE SELECT]. Select the desired file and select • mark appears on the file. To select other files, repeat this step. • To check the content of the file, select [CHECK]. - Page 59 Managing Files Protecting the Currently Displayed File After performing steps 1-3 (Z p. 57) Select [CURRENT]. Select [YES]. You can select the previous or next file by selecting % or &. To quit the screen Select [QUIT]. Protecting Selected Files After performing steps 1-3 (Z p.
-
Page 60: Viewing File Information
Viewing File Information Preparation: mode: Pause the playback. Otherwise, select the file on the index screen. mode: Play back the still image. Otherwise, select the file on the index screen. Press INFO. • FILE ( mode): File name • FOLDER ( mode): Folder name •... -
Page 61: Changing The Event Registration
Managing Files Changing the Event Registration Preparation: • Select mode. • Select the playback mode. Touch MENU. Select [EDIT]. Select [CHANGE EVENT REG.]. Changing the Event of the Currently Displayed File After performing steps 1-3 Select [CURRENT]. Select [YES]. You can select the previous or next file by &... -
Page 62: Dividing Files
Dividing Files You can divide a selected video into two. Preparation: • Select mode. • Select the playback mode. Touch MENU. Select [EDIT]. Select [DIVIDE]. Select the desired file. Playback starts. Select [SET] at the point you want to divide the file. It is recommended to select [SET] after the pause button is pressed. -
Page 63: Trimming Files
Managing Files Trimming Files You can select the necessary part of the video and save it as a new video file. Preparation: • Select mode. • Select the playback mode. Touch MENU. Select [EDIT]. Select [TRIMMING]. Select the desired file. Select [SET] at the start point. -
Page 64: Face Detection Zoom
Face Detection Zoom You can enlarge the part including a face in a still image and save it as a new file. Preparation: • Select mode. • Select the playback mode. Select the desired still image. Select Touch the touch sensor to select the face to zoom. -
Page 65: Playlists
Playlists It is a list that enables you to organize recorded videos in order of preference. Preparation: • Select mode. • Select the playback mode. Creating Playlists Touch MENU. Select [EDIT PLAYLIST]. Select [NEW LIST]. Select an item and display files. •... -
Page 66: Playing Back Playlists
Creating Playlists Including Picture Titles You can easily create a playlist including a picture title. Press TITLE. Select the desired picture title. You can check the picture title in full-screen by selecting [CHECK]. Select the desired file. You can check the scene by selecting [CHECK]. -
Page 67: Other Operations Of Playlists
Playlists (Continued) Other Operations of Playlists You can perform additional editing and delete files in a created playlist. Adding/Deleting Files in Playlist After performing steps 1-2 (Z p. 64) Select [EDIT]. Select the playlist you want to edit. To add or delete files, follow the steps 5 to 8. -
Page 68: Print Setting
(Digital Print Order Format). You can set which images to be printed and the number of prints with this camcorder. This feature is useful to print with a DPOF-compatible printer or take the SD card to a photo lab for printing. -
Page 69: Direct Printing With Pictbridge Printer
(Continued) Direct Printing with PictBridge Printer If your printer is compatible with PictBridge, still images can be printed easily by connecting the camcorder directly to the printer with the USB cable. Preparation: Press the < (Power) button for more than 2 seconds to turn off the camcorder. -
Page 70: Copying
Copying Files Copying/Moving Files You can copy or move files between the built-in memory and the SD card. mode mode Preparation: • Select mode. • Select the playback mode. • Make sure that SD card is inserted in the SD card slot. -
Page 71: Using A Bd/Dvd Burner
Copying Files Using a BD/DVD Burner The files in the camcorder can be backed up to a disc using a BD/DVD burner. • Use one of the following methods to view the disc. (If you try to play back the disc with incompatible player, the disc may not be ejected.) - Page 72 To quit the screen 1) Select [QUIT]. 2) When [QUIT?] appears, select [YES]. NOTE This method can be used to copy video files to discs in a computer connected to the camcorder. Selecting Files for Backup Preparation: • Select mode.
- Page 73 To play back the created disc in the BD/DVD burner using the camcorder 1) Connect the camcorder to the BD/DVD 2) Turn on the camcorder first, then turn on 3) Insert the disc. 4) Select [PLAYBACK]. 5) Select the desired folder. ( 6) Select the desired file.
-
Page 74: Using A Usb External Hard Disk Drive
Refer also to the optional USB external hard disk drive’s instruction manual. • When connecting to a Seagate’s FreeAgent™ Desk series product, use a USB cable with Mini-A(Male) to Mini-B(Male) connectors. JVC’s QAM0852-001 (optional) is recommended. Refer to page 35 for information on contacting JVC. •... - Page 75 • Do not format the USB external hard disk drive using the PC. If you did, format again using the camcorder. (All the data in the USB external hard disk drive will be erased.) • Avoid the following operations using the PC.
-
Page 76: Uploading Files To Websites
Uploading Files to Websites Upload Trimming You can select the necessary part of the video and save it as a new video file ready for uploading. Preparation: • Select mode. • Select the playback mode. Touch MENU. Select [UPLOAD SETTINGS]. Select the desired file. -
Page 77: Operating In Conjunction With Tv Via Hdmi
HDMI cables. NOTE • Not all HDMI-control devices comply with the HDMI-CEC standard. The HDMI control function of the camcorder will not work when connected to these devices. • The camcorder is not guaranteed to operate with all HDMI-CEC-enabled devices. -
Page 78: Further Information
2 seconds after SNAPSHOT is pressed. • You can confirm the countdown on the camcorder screen. • It is recommended to attach the camcorder to a tripod and use this function to prevent the vibration after SNAPSHOT is pressed. - Page 79 SNAPSHOT is pressed. BRACKETING*: Activates the bracket shooting function. In addition to an image with the exposure set by the camcorder, four other images are recorded with exposure values shifted (between –0.6 EV and +0.6 EV by 0.3 EV). You can select the image that has a suitable exposure after shooting.
- Page 80 Complete stabilization may not be possible if hand shake is excessive, or depending on the shooting conditions. • Switch off this mode when recording with the camcorder on a tripod. OFF: Deactivates the function. AGC: Electrically brightens the scene in dark place.
- Page 81 Changing the Menu Settings Mode Menus x.v.Color Records video in the color range suitable for viewing in an x.v.Color™ compliant TV. WIND CUT Reduces noise caused by wind. 4 GRID Displays grid lines on the monitor to help compose the subject accurately.
- Page 82 Menus DISPLAY SETTINGS LANGUAGE Sets the display language. CLOCK ADJUST Sets the time. DATE DISPLAY STYLE Sets the date and time display format. MONITOR BRIGHT Sets the brightness of the LCD monitor. MONITOR BACKLIGHT Enables you to adjust the brightness of backlight on the monitor.
- Page 83 The demonstration only works when the AC adapter is connected, not with the battery pack. • If an SD card is in the camcorder, demonstration will not take place even if this mode is set to [ON]. OFF: Disables the function.
- Page 84 DVD are finalized automatically even if the setting is [OFF]. YES: Performs this function. [NO]: Cancels this function. NOTE Information about obtaining system update will be made available on the JVC’s web site. YES: Performs this function. [NO]: Returns to the menu screen without executing reset.
- Page 85 Changing the Menu Settings Menus CONNECTION SETTINGS DISPLAY ON TV Displays camcorder’s on-screen display on a TV screen. VIDEO OUTPUT Sets the aspect (16:9/4:3) to the screen of the connected television when outputting videos from the AV connector. COMPONENT OUTPUT...
- Page 86 Ensures stable speeds and operation when accessing the built-in memory. FORMAT SD CARD You have to format newly purchased SD cards with this camcorder before using them. This will also ensure stable speeds and operation when accessing the SD card.
-
Page 87: Troubleshooting
Fully charge the battery pack, run it down, and then recharge it again. • If the camcorder is used for long periods of time in high or low temperatures, or if the battery pack is repeatedly charged, the amount of remaining battery may not be displayed correctly. - Page 88 Set [WB] in [MANUAL SETTING] appropriately to the light source. • Select [MWB] in [WB] while holding a sheet of plain white paper in front of the camcorder so that the white paper fills the screen. Keep touching OK until the •...
- Page 89 Set [EFFECT] to [OFF]. • If there are many files (such as video) in the camcorder, it takes time for the camcorder to respond. It is recommended that you copy all files from the camcorder onto your computer, and erase the files from the camcorder.
-
Page 90: Cleaning
If a malfunction occurs in the built-in memory ! P erform [FORMAT BUILT-IN MEM.]. (All data is deleted.) # If this does not solve the problem, contact the JVC customer service for repairs. To reset the camcorder when it does not operate normally ... -
Page 91: Warning Indications
Set the clock. If the message still appears after setting the clock, the battery for the clock has been depleted. Consult your nearest JVC dealer. • Be sure to use JVC battery packs. • Set [REC MEDIA FOR VIDEO] to [BUILT-IN MEMORY]. •... - Page 92 Replace the backup destination with another disc. • Move the files or folders to a PC or other devices, and then format the built-in memory of the camcorder or the SD card. • Select [FILE + MANAGEMENT NO] in [FORMAT BUILT-IN MEM.] or [FORMAT SD CARD].
-
Page 93: Jvc Software License Agreement
1 COPYRIGHT; OWNERSHIP You acknowledge that all copyrights and other intellectual property rights in the Program are owned by JVC and its licensor, and remain vested in JVC and such licensor. The Program is protected under the copyright law of Japan and other countries, and related Conventions. - Page 94 Should You breach any provision of this Agreement, JVC may terminate this Agreement without giving any notice to You. In this event, JVC may claim against You for any damages caused by Your breach. Should this Agreement be terminated, You must...
-
Page 95: Terms
Aperture Priority ...48 Auto Finalize ...83 Auto Power Off ...82 Backlight Compensation ...50 BD/DVD Backup ...70 BD/DVD Burner ...70 Brightness Adjustment ...47 Component Output ...84 Continuous Shooting Speed ...82 Copying Files ...69 Date Display Style ...81 Deleting Files ...56 Demo Mode ...82 Digest Playback ...72 Display on TV ...84 Dividing Files ...61...