KitchenAid 30” Electric Freestanding Range Installation Instructions page 4

Four-wire electrical connection:
ing
ew
8. Remove the grounding-link screw from the range
frame. Save the grounding-link screw. Bend up the
grounding link so that it does not contact the range.
See Figure 8.
bare
wire
from
powe
suPPI
cable
grounding-
link screw
9. Connect the bare grounding wire from power supply
cable to the range using the grounding-link screw.
The grounding wire must be attached first and
must not contact any other terminal. See
Figure 9
silver-colored
bare wire
from power
supply cabl
connector and
Figure 10 wg:r supply
IO. Connect the neutral wire (white wire) to the center,
silver-colored terminal screw on the terminal block
using the brass nuts that are attached to the
terminal block cover. See Figure 10.
Il. Connect the other two wires to the outer terminals
on the terminal block. See Figure 10.
12. Do NOT loosen the factory installed nuts already
on the terminal. Tighten nuts with 3/8" nut driver for
proper electrical connection.
13. Tighten the locking ring and clamping screws of the
conduit connector.
14. Replace the terminal block cover.
Three-wire electrical connection:
Use this method ONLY if local codes PERMIT
connecting cabinet-grounding conductor to neutral
wire of power supply cable.
3. Use the brass terminal nuts attached to the
knockout opening to connect the neutral wire (white
wire) to the silver-colored terminal screw on the
terminal block. See Figure 11.
3. Connect the other two wires to outer terminal
screws on the terminal block. See Figure 11.
IO.Do Not loosen factory-installed nuts already on the
terminal. Tighten nuts with 318" nut driver for proper
electrical connection.
I1 .Tighten the locking ring and clamping screws of the
conduit connector.
12,Reinstall the terminal block cover.
Excessive Weight Hazard
Use two or more people to move and install range.
Failure to follow this instruction can result in back
or other injury.
1
18.1
Firmly grasp the range and gently lay it on its
back on the cardboard corners.
El
Pull cardboard bottom and shipping base firmly
to remove.
110
Place cardboard or hardboard in front of
range. Stand range back up onto cardboard
n
or hardboard.
Panel C
Tip Over Hazard
Connect anti-tip bracket to the
range.
Reconnect anti-tip bracket, if
the range is moved.
Do not push down on the
open oven door.
Follow the installation
instructions.
Do not let children climb onto
the oven door.
Failure to follow these
instructions can result in
death, burns, or other injury.
Electrical Shock Hazard
Take special care when drilling holes into the
Press on front of
floor. Electrical wires or plumbing may be located
storage drawer
beneath floor.
and release to
Locate the electrical circuits that could be
affected by the installation of this bracket and
turn off power to these circuits.
Failure to follow these instructions may result in
death, fire or electrical shock.
II 1 =I
I
1
Place the anti-tip bracket
template on the floor in the
I I
cab/net opening so that the
left edge is against cabinets
and the top edge is against
the rear wall, molding or
cabinet.
f il
25"
countertop
over 24"
cabinet
If countertop opening is
deeper than 25 inches,
measure and mark a
distance 25 inches in from
front of countertop
opening
and align
template with mark (or
subtract 25 inches from
countertop depth and add
the difference to the
corresponding dimension).
If countertop is not flush to
the side of cabinet
opening, align the left side
of the template to allow for
the countertop overhang.
Tape the range anti-tip
bracket template in place.
Countertop
overhangs
'cabinet
side.
PI
Insert storage drawer into slide rails on sides
.
of drawer opening. Lift front of drawer
slightly and push firmly to close drawer.
120
Push in and
. turn each
surface unit
A = Difference
control knob to "HI"
between
position. Check the
countertop
irth and
operation of the cooktop
II
elements and indicator lights.
Contact a qualified floor covering installer for the
best procedure of drilling mounting holes through
your type floor covering.
Before moving, slide range onto cardboard or
hardboard.
11
To mount
anti-tip
. bracket to
wood floor,
use the anti-tip bracket
template to mark where to
drilfmounting holes. Use a
drill with a 118" drill bit to
drill the two holes. Remove
template from floor.
To mount anti-tip bracket
to concrete or ceramic
floor,
use the anti-tip
bracket template to mark
where to drill mounting holes. Use a drill with a 3/16"
masonry drill bit to drill the two holes. Remove template
from floor. Tap plastic anchors into mounting holes in
floor with hammer.
11
Line up holes in anti-tip
. bracket with holes in floor.
Use the screws provided to
fasten anti-tip bracket to floor.
NOTE: Anti-tip bracket must be mounte
securely to the sub floor.
Depending on the thickness of
your flooring, longer screws
may be necessary to anchor '
the bracket to the sub floor.
Longer screws are available
from your local hardware store.
11
Move range close to cabinet opening.
. Plug power supply cord into grounded outlet
or connect power supply cable to junction
box. See "Electrical requirements," panels A and B for
details. "88:88" should appear in the clock display.
Remove cardboard or hardboard from
under range. Carefully move range
open. Pull open
to first stop position7
Lift front of drawer to clear white
wheels in drawer guides. Remove drawer -
and set it aside on a protected surface.
)17
Look under range (a
. flashlight may be
needed) to check that
left rear leveling leg is engaged in
the anti-tip bracket. If leveling leg is
not properly engaged, remove and v
reposition the anti-tip bracket to
u
insure that the leveling leg fits properly in the anti-tip
bracket.
11
Place rack in oven. Place le
rack, first side to side; then front to back. If the range ' '
is not level, pull range forward until the rear leveling leg is
removed from the anti-tip bracket. Adjust the leveling legs
up or down. Then slide range back into position. Check
that leveling leg is engaged in anti-tip bracket.
NOTE: Oven must be level for satisfactory baking
conditions.
OFF
1211
Press the "Clock Set" button. "TIME, HR
. AND MIN" will light up in the display. "0:OO"
will appear and the ":" will be flashing. Press
the number buttons for the correct time of day. Press
"Stat-t/Enter" button to start the clock.
)22/
Check the operation of the oven element.
. Press the "BAKE" button. "350"" will appear
In the temperature display. The ON, Bake
Element, Outer Broil Element and Oven Cavity symbols
will light up in the display. Press the "Start/Enter" button.
The bottom element should glow red and the indicator
light should be on. The upper element should become
hot but not glow red. The oven indicator light goes off
when the oven is preheated.
Press "Cancel/OFF" button.
B-l
Check the operation of the broil element.
. Press the "BROIL" button. "500"" will appear
in the temperature display. The ON, Inner
and Outer Broil Elements and Oven Cavity symbols will
light up in the display. Press the "Start/Enter" button.
The top element should glow red and the indicator light
should be on.
Press the "Cancel/OFF" button.