Related Manuals for JVC KD-G464
Summary of Contents for JVC KD-G464
- Page 1 CD RECEIVER KD-G464 For canceling the display demonstration, see page 7. For installation and connections, refer to the separate manual. INSTRUCTIONS GET0302-001B [UI]...
-
Page 2: How To Reset Your Unit
• If a disc is loaded, it will eject. Be careful not to drop the disc. Thank you for purchasing a JVC product. How to forcibly eject a disc If a disc cannot be recognized by the receiver or cannot be ejected, ejects the disc as follows. -
Page 3: Table Of Contents
How to reset your unit ... How to forcibly eject a disc ... How to read this manual ... How to use the MODE button ... Control panel — KD-G464 Parts identification ... Remote controller — RM-RK50 Main elements and features ... -
Page 4: How To Read This Manual
Press and hold both buttons at the same time. The following marks are used to indicate... : Built-in CD player operations. : External CD changer operations. How to use the MODE button If you press MODE, the receiver goes into functions mode, then the number buttons and 5/∞... -
Page 5: Control Panel
Disc type indicators—WMA, MP3 f Playback source indicators— CH: Lights up only when CD-CH is selected as the playback source. CD: Lights up for the built-in CD player. g Playback mode / item indicators— RND (random), RPT (repeat) h LOUD (loudness) indicator... -
Page 6: Remote Controller
Remote controller — Installing the lithium coin battery (CR2025) • When operating, aim the remote controller directly at the remote sensor on the receiver. Make sure there is no obstacle in between. Warning: • Store the battery in a place where children cannot reach to avoid risk of accident. -
Page 7: Getting Started
Getting started Ÿ You cannot select some sources if they are not ready. For FM/AM tuner only ⁄ Volume level appears. Volume level indicator Basic operations Adjust the sound as you want. (See pages 17 and 18.) To drop the volume in a moment (ATT) To turn off the power Caution on volume setting: Discs produce very little noise compared... -
Page 8: Canceling The Display Demonstrations
Canceling the display demonstrations If no operations are done for about 20 seconds, display demonstration starts. [Initial: DEMO ON]—see page 20. Finish the procedure. To activate the display demonstration In step 3 above... Setting the clock Set the hour and minute. 1 Select “CLOCK H”... -
Page 9: Radio Operations
Radio operations Ÿ Lights up when receiving an FM stereo broadcast with sufficient signal strength. Selected band appears. Start searching for a station. When a station is received, searching stops. To stop searching, press the same button again. To tune in to a station manually In step ! above... -
Page 10: Storing Stations In Memory
Storing stations in memory You can preset six stations for each band. FM station automatic presetting — SSM (Strong-station Sequential Memory) Select the FM band (FM1 – FM3) you want to store into. “SSM” flashes, then disappears when automatic presetting is over. Local FM stations with the strongest signals are searched and stored automatically in the FM band. -
Page 11: Disc Operations
Disc operations Playing a disc in the receiver About MP3 and WMA discs MP3 and WMA (Windows Media “tracks” (words “file” and “track” are used interchangeably) are recorded in “folders.” • When inserting an MP3 or a WMA disc: Total folder Total track number number... -
Page 12: Playing Discs In The Cd Changer
About the CD changer It is recommended to use the JVC MP3- compatible CD changer with your receiver. • You can also connect other CH-X series CD changers (except CH-X99 and CH-X100). However, they are not compatible with MP3 discs, so you cannot play back MP3 discs. - Page 13 • When the current disc is an MP3 disc: Selected folder number Folder name Disc information appears automatically (see page 15). Clock Current track number “ROOT” appears if no folder is included in the disc. • When the current disc is an audio CD or a CD Text disc: CD Text: Disc title/performer = Track title appears automatically...
-
Page 14: Other Main Functions
To locate a particular track (for CD) or folder (for MP3 or WMA discs) directly To select a number from 01 – 06: To select a number from 07 – 12: • To use folder search on MP3/WMA discs, it is required that folders are assigned with 2-digit numbers at the beginning of their folder names—01, 02, 03, and so on. -
Page 15: Changing The Display Information
Changing the display information While playing an audio CD or a CD Text ( If the current disc is an audio CD, “NO NAME” appears. While playing an MP3 ( • When “TAG DISP” is set to “TAG ON” (see page 20) If an MP3/WMA file does not have ID3 tags, folder name and file name appear. -
Page 16: Selecting The Playback Modes
You can use only one of the following playback modes at a time. Select your desired playback mode. Repeat play Ex.: When “TRK RPT” is selected while playing an MP3 disc in the receiver Random play Ex.: When “DISC RND” is selected while playing an MP3 disc in the receiver Only while playing an MP3 ( Only while playing discs in the CD changer (... -
Page 17: Sound Adjustments
Sound adjustments Selecting preset sound modes You can select a preset sound mode suitable to the music genre. Ex.: When “ROCK” is selected Indication pattern for each sound mode: (C-EQ: custom equalizer) Preset values Indication For: BAS * USER (Flat sound) ROCK Rock or disco music... -
Page 18: Adjusting The Sound
Adjusting the sound You can adjust the sound characteristics to your preference. Ex.: When “TRE” is selected Indication pattern changes as you adjust the level. Indication To do: BAS* Adjust the bass. (bass) TRE* Adjust the treble. (treble) FAD* Adjust the front (fader) and rear speaker balance. -
Page 19: General Settings - Psm
General settings — PSM Basic procedure You can change PSM (Preferred Setting Mode) items listed in the table on the next page. Select a PSM item. Ex.: When you select “DIMMER” Adjust the PSM item selected. Repeat steps to adjust the other PSM items if necessary. - Page 20 : Repeats scrolling (5-second intervals in between). : Cancels. • Pressing DISP for more than one second can scroll the display regardless of the setting. CHANGER : [Initial]; To use a JVC CD changer, [12]. EXT IN : To use another external component, [22]. TAG ON : [Initial];...
-
Page 21: Detaching The Control Panel
Detaching the control panel When detaching or attaching the control panel, Attaching the control panel be careful not to damage the connectors on the back of the control panel and on the panel holder. Detaching the control panel Before detaching the control panel, be sure to turn off the power. -
Page 22: External Component Operations
External component operations You can connect an external component to the CD changer jack on the rear using the Line Input Adapter KS-U57 (not supplied). • For connection, see Installation/Connection Manual (separate volume). • Before operating the external component, select the external input correctly (see page 20). -
Page 23: Maintenance
• After starting the heater in the car. • If it becomes very humid inside the car. Should this occur, the CD player may malfunction. In this case, eject the disc and leave the receiver turned on for a few hours until the moisture evaporates. -
Page 24: More About This Receiver
More about this receiver Basic operations Turning on the power • By pressing SOURCE on the receiver, you can also turn on the power. Turning off the power • If you turn off the power while listening to a disc, disc play will start from where playback has been stopped previously, next time you turn on the power. - Page 25 Playing an MP3/WMA disc • This receiver can play back MP3/WMA files with the extension code <.mp3> or <.wma> (regardless of the letter case—upper/lower). • This receiver can show the names of albums, artists (performer), and ID3 Tag (Version 1.0, 1.1, 2.2, 2.3, or 2.4) for MP3 files and for WMA files.
-
Page 26: Troubleshooting
The antenna is not connected firmly. Disc is inserted upside down. CD-R/CD-RW is not finalized. Disc is locked. The CD player may have functioned incorrectly. You are driving on rough roads. Disc is scratched. Connections are incorrect. No disc in the loading slot. - Page 27 Symptoms • Disc cannot be played back. • Noise is generated. • A longer readout time is required (“CHECK” keeps flashing on the display). • Tracks cannot be played back as you have intended them to play. • Elapsed playing time is not correct.
- Page 28 Symptoms • “NO DISC” appears on the display. • “NO MAG” appears on the display. • “RESET 8” appears on the display. • “RESET 1” – “RESET 7” appears on the display. • The CD changer does not work at all. Causes No disc is in the magazine.
-
Page 29: Specifications
Stereo Separation: 30 dB Capture Ratio: 1.5 dB [AM Tuner] Sensitivity: 20 µV Selectivity: 35 dB CD PLAYER SECTION Type: Compact disc player Signal Detection System: Non-contact optical pickup (semiconductor laser) Number of Channels: 2 channels (stereo) Frequency Response: 5 Hz to 20 000 Hz... - Page 30 Having TROUBLE with operation? Please reset your unit Refer to page of How to reset your unit 0305DTSMDTJEIN © 2005 Victor Company of Japan, Limited...
-
Page 31: Installation (In-Dash Mounting)
GET0302-002A [UI] This receiver is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers. Parts list for installation and connection The following parts are provided for this receiver. -
Page 32: Electrical Connections
Notes: • Replace the fuse with one of the specifi ed rating. If the fuse blows frequently, consult your JVC car audio dealer. • It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change “AMP GAIN”...