Page 1
CD/SD RECEIVER RECEPTEUR CD/SD KD-LHX552/KD-LHX551 For canceling the display demonstration, see page 8. Pour annuler la démonstration des affichages, référez-vous à la page 8. For installation and connections, refer to the separate manual. Pour l’installation et les raccordements, se référer au manuel séparé.
How to reset your unit This will reset the microcomputer. Your preset adjustments will also be erased. Thank you for purchasing a JVC product. How to forcibly eject a disc If a disc cannot be recognized by the receiver or cannot be ejected, ejects the disc as follows.
How to forcibly eject a disc ... How to read this manual ... How to change the display pattern during playback ... Control panel — KD-LHX552/KD-LHX551 Parts identification ... Remote controller — ... 6 RM-RK300 Main elements and features ...
Press and hold both buttons at the same time. The following marks are used to indicate... : Built-in CD player operations. : External CD changer operations. : SD player operations. How to change the display pattern during playback Source operation screen RDS Radiotext (RT) or DLS screen is shown when the source is “TUNER”...
“Ext Input” setting (see page 34). If the source is not ready, you cannot select the source. Key icon appears as negative pattern. KD-LHX552/KD-LHX551 Parts identification 5 0 (eject) button 6 T/P (traffic programme/programme type) button 7 MENU button...
Remote controller — Installing the lithium coin battery (CR2025) • When operating, aim the remote controller directly at the remote sensor on the receiver. Make sure there is no obstacle in between. Warning: • Store the battery in a place where children cannot reach to avoid risk of accident.
Getting started Ÿ Select the source. You can also select the source by... ⁄ Adjust the sound as you want. (See pages 24 and 25.) Basic operations To drop the volume in a moment (ATT) To turn off the power Caution on volume setting: Discs produce very little noise compared with other sources.
Canceling the display demonstrations If no operations are done for about 20 seconds, display demonstration starts. [Initial: Interval]—see page 30. Select “Off.” Exit from the setting. To activate the display demonstration In step 2 above, select “All Time” or “Interval.” For more details, see page 30.
Radio operations Select “TUNER.” Ÿ Select the band (FM/AM). Start searching for a station. When a station is received, searching stops. To stop searching, press the same icon again. Listening to the radio To tune in to a station manually In step on the left...
Storing stations in memory You can preset six stations for each band. FM station automatic presetting — SSM (Strong-station Sequential Memory) Select the FM band (FM1 – FM3) you want to store into. Local FM stations with the strongest signals are searched and stored automatically in the FM band.
Listening to a preset station Select a preset station (1 – 6) you want. • Holding can display the Preset Station List (see below). To select a preset station using the Preset Station List Appears only for FM. Select a preset number. Preset Station List The lists show either the station frequency or PS name (the first 8 characters).
FM RDS operations Searching for your favorite FM RDS programme You can tune in to a station broadcasting your favorite programme by searching for a PTY code. • To store your favorite programme, see page Ÿ Select a PTY code. If there is a station broadcasting a programme of the same PTY code as you have selected, that station is tuned...
Storing your favorite programmes You can store six favorite programme types. Preset programme types: Select a PTY code. Select a preset number. Selected PTY code is stored in the selected preset number. Repeat steps to store other PTY codes into other preset numbers.
To deactivate the TA Standby Reception The TP indicator goes off. PTY Standby Reception PTY Standby Reception allows the receiver to switch temporarily to your favorite PTY programme from any source other than AM. • This function also takes effect for the DAB tuner.
Using the message service— RDS Radiotext (RT) What is RDS Radiotext RDS Radiotext is part of the RDS data signal to transmit various text information (e.g. programme information, phone numbers, e-mail and web addresses, artist/title information and news headlines). The text service is part of the RDS broadcast.
Disc/SD card operations About MP3 and WMA tracks MP3 and WMA (Windows Media “tracks” (words “file” and “track” are used interchangeably) are recorded in “folders.” • When an MP3 or a WMA folder includes an image <jll> file edited by Image Converter (Wide Ver 1.2)—supplied in the CD-ROM, you can show the image on the display while the tracks in the folder are...
Playing discs in the CD changer About the CD changer It is recommended to use the JVC MP3- compatible CD changer with your receiver. • You can also connect other CH-X series CD changers (except CH-X99 and CH-X100). However, they are not compatible with MP3 discs, so you cannot play back MP3 discs.
About the SD card You can play back MP3/WMA tracks recorded on the SD card and show the stored image on the display during playback— ImageLink. (See pages 16, 30, and 48 for details.) The required SD recording format is FAT 12/16 and the recommended storage type is 8 MB to 512 MB.
Page 19
If an SD card has been loaded... The album name/performer with indicator and the track title with indicator will appear if “Tag” is set to “On” (see page 32). Operation screens used for the following operations is of MP3 playback in the receiver.
To select a disc during playback • If you hold the icon, the Disc List will appear on the display (see the right column). Prohibiting disc ejection You can lock a disc in the loading slot. “No Eject” flashes, and the disc cannot be ejected.
Page 21
If you select the current folder (highlighted on the screen), its File List appears. • Select a track (only for MP3/WMA disc or SD card). File List of the current folder appears. Appears only if the current disc is an MP3 discs.
Page 22
Ex.: To select track 32 while playing track 6 in the CD changer * If the source is “CD-CH”: Works only when JVC MP3 compatible CD changer (CH-X1500) is connected. (3 times) First time you press “+10” or “–10,” the...
Selecting the playback modes You can use only one of the following playback modes at a time. Select your desired playback mode. Mode Intro play Track: Folder* Disc* Off: Mode Repeat play Track: Folder* Disc* Off: Mode Random play Folder* Disc or SD: All tracks of the current disc or the SD card.
Sound adjustments Setting the basic sound selection menu—SEL Ÿ Select a setting item. Adjust the selected item. A To adjust the speaker output balance between the front and rear speakers—FAD (fader). To adjust the speaker output balance between the left and right speakers— BAL (balance).
Selecting preset sound modes (i-EQ: intelligent equalizer) You can select a sound mode suitable to the music genre. Available sound modes FLAT (No sound mode is applied), HARD ROCK, R & B, POP, JAZZ, DANCE, COUNTRY, REGGAE, CLASSIC, USER 1, USER 2, USER 3 Select a sound mode.
Graphic displays Before starting the following procedure, prepare a CD-R or an SD card including still images (pictures) and animations (movies). • With Image Converter (Wide Ver 1.2) included in the supplied CD-ROM, you can create your own images and animations. (Samples are included in the CD-ROM.) Insert a CD-R, an SD card, or supplied CD-ROM.
Downloading an animation or pictures • It takes a long time to download an animation. For details, see page 49. • To activate the downloaded files, see page 29. In step on page 26... Appears only if “PICTURE” is selected. •...
Page 28
Appears only if “PICTURE” is selected. • To delete the stored animation File name appears. • To delete the stored pictures File name appears. Repeat step to delete more pictures. Exit from the setting. Deleting all the stored animation and pictures •...
Activating the downloaded fi les • To activate the animations stored for opening and ending screens 1 Select “Opening” or “Ending.” 2 Select a setting you want. Default: Factory-preset animation is used. User: Your own edited animation is used. • To activate the graphic screen using either picture or movie 1 Select “Graphics.”...
General settings — PSM Basic procedure You can change PSM (Preferred Setting Mode) items listed in the table that follows. Select a PSM category. You can move to a different category by simply changing the PSM items. Indications Demo Display demonstration Graphics Graphics Select a PSM item.
Page 31
Indications KeyIn CFM Key-in confirmation Opening Opening screen Ending Ending screen UserPict. User picture Clock Hr Clock hour Clock Min Clock minute 24H/12H Clock system Clock Adj Automatic clock adjustment Scroll Scroll Displayed only after a downloadable file is stored in memory. Displayed only after a downloadable file is stored in memory and while selecting “UserPict.”...
Page 32
Indications Dimmer Dimmer From– To Dimmer time Contrast Contrast LCD Type Display type Font Type Font type Tag display Theme Audio level meter Key Info Key information Sensitiv. Touch panel sensitivity Displayed only when “Dimmer” is set to “Time Set.” Depends on the “Dimmer”...
Page 33
Indications PTY Stnby PTY Standby AF-Regn’l Alternate frequency/ regionalization reception TA Volume Traffic announcement volume P-Search Programme search IF Filter Intermediate frequency filter DAB AF Alternative frequency reception Announce Announcement standby Depends on the amplifier gain control. Displayed only when the DAB tuner is connected. Selectable settings, [reference page] You can select one of the PTY codes for the PTY Standby Reception, [14].
Page 34
O (back to the beginning) • The indication on the display will also be shown in the selected language. Changer: [Initial]; To use a JVC CD changer, [17]. Ext In: To use any external component, [39]. Muting1/Muting2: Select either one which mutes the sounds while using the cellular phone.
Selecting the dimmer mode You can dim the display at night or as you set the timer. Dims the display when you Auto: turn on the headlights. \ Go to step 9. Off: Cancels. \ Go to step 9. Always dims the display. \ Go to step 9.
Page 36
Select the source. \ CD \ SD \ Changer AllSource* ) \ Line In \ FM \ AM (or Ext In* \ DAB* \ (back to the beginning) When you select “AllSource,” you can use the same color for all the sources. Depends on the “Ext Input”...
Other main functions Assigning titles to the sources You can assign titles to CDs (both in this receiver and in the CD changer) and the external components (LINE-IN and EXT-IN). Maximum number of Sources CDs/CD-CH Up to 32 characters (up to 30 discs) External components Up to 8 characters •...
Changing the control panel angle Detaching the control panel When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder. Detaching the control panel Before detaching the control panel, be sure to turn off the power.
External component operations You can connect an external component to the LINE IN plugs on the rear—LINE-IN and another to the CD changer jack on the rear using the Line Input Adapter KS-U57 (not supplied)—EXT-IN. • For connection, see Installation/Connection Manual (separate volume).
DAB tuner operations Select “DAB.” Ÿ Select the band (DAB1/DAB2/ DAB3). Start searching for an ensemble. When an ensemble is received, searching stops. To stop searching, press the same icon again. ⁄ Select a service (either primary or secondary) to listen to. Listening to the DAB tuner To tune in to an ensemble manually In step...
Page 41
33). It is recommended to use DAB (Digital Audio Broadcasting) tuner KT-DB1000 with your receiver. If you have another DAB tuner, consult your JVC IN-CAR ENTERTAINMENT dealer. • Refer also to the Instructions supplied for your DAB tuner. When surrounding sounds are noisy...
Storing DAB services in memory You can preset 6 DAB services (primary) for each band. Ex.: Storing an ensemble (primary service) into the preset number 1 of the DAB1 band. Select an ensemble (primary service). • Holding Preset Service List (see step 5). * Moves to the other DAB bands.
Change a service if necessary. Using the standby reception You can use three types of Standby Reception. • Road Traffic News Standby Reception—TA Standby Reception (see the following). • Announcement Standby Reception (see the right column) • PTY Standby Reception (see page 44). Road Traffic News Standby Reception (TA Standby Reception) Road Traffic News Standby Reception allows...
To deactivate the Announcement Standby Reception Select “ANN Off” in step 2 on page 43. The ANN indicator goes off. PTY Standby Reception PTY Standby Reception allows the unit to switch temporarily to your favorite PTY programme from any source other than AM. •...
• After starting the heater in the car. • If it becomes very humid inside the car. Should this occur, the CD player may malfunction. In this case, eject the disc and leave the receiver turned on for a few hours until the moisture evaporates.
More about this receiver Basic operations General • The clock in the “BACK” icon on the screen works as the time countdown indicator. If no operation is done for a certain period of time, the current screen goes off, and the source operation screen resumes.
Page 47
• When a disc or SD card has been loaded, selecting “CD” or “SD” for the playback source starts playback. • When a track or folder whose number is greater than 99 is selected, the icon before the number ( , ) goes off (to show its assigned 3-digit number).
Page 48
• For MP3/WMA discs: The maximum number of characters for file/ folder names vary among the disc format used (includes 4 extension characters—<.mp3> or <.wma>). – ISO 9660 Level 1: up to 12 characters – ISO 9660 Level 2: up to 31 characters –...
Page 49
Storing your own sound modes • If you do not want to store your current adjustment, but only to apply the adjustment to the current playback source, press “BACK” repeatedly to go back to the operation screen of the current source. Adjustment you made remains effective until you select a sound mode.
The built-in shock-proof circuit is working. CD-R/CD-RW is not finalized. Disc is locked. The CD player may have functioned incorrectly. Remedies Finish the operation within the time limit. Adjust it to the optimum level. Check the cords and connections.
Page 51
Symptoms • Disc sound is sometimes interrupted. • “No Files” appears on the display for a while. • Noise is generated. • Elapsed playing time is not correct. • “Not Support” appears on the display and track skips. • “No Music” appears on the display.
Page 52
Disc is inserted upside down. No disc is in the magazine. This receiver is not connected to the CD changer correctly. The CD player may have functioned incorrectly. The built-in microcomputer may have functioned incorrectly due to noise, etc. Remedies Select “On”...
Specifications AUDIO AMPLIFIER SECTION Maximum Power Output: Front: 52 W per channel Rear: 52 W per channel Continuous Power Output (RMS): Front: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion.
Page 54
Cette procédure réinitialise le micro- ordinateur. Vos ajustements préréglés sont aussi effacés. Merci pour avoir acheté un produit JVC. Comment forcer l’éjection d’un disque Si un disque ne peut pas être reconnu ou ne peut pas être éjecté par l’autoradio, forcez l’éjection de la façon suivante.
Page 55
Comment forcer l’éjection d’un disque ... Comment lire ce manuel ... Comment changer le modèle d’affichage pendant la lecture ... Panneau de commande — KD-LHX552/KD-LHX551 Identification des parties ... Télécommande — RM-RK300 Composants principaux et caractéristiques ... Pour commencer ... 7 Opérations de base ...
Comment lire ce manuel Les méthodes suivantes sont utilisées pour rendre les explications simples et faciles à comprendre. • Certains conseils et remarques sont donnés dans la section “Pour en savoir plus à propos de cet autoradio” (voir les pages 46 à 49). •...
“SourceExt” (voir page 34). Si la source n’est pas prête, vous ne pouvez pas la choisir. L’icône de la touche apparaît en négatif. KD-LHX552/KD-LHX551 Identification des parties 5 Touche 0 (éjection) 6 Touche T/P ( routières/type de programme 7 Touche MENU 8 Bouton de réinitialisation...
Télécommande — Mise en place de la pile-bouton au lithium (CR2025) • Pour l’utiliser, dirigez la télécommande directement sur le capteur de télécommande de l’autoradio. Assurez-vous qu’il n’y a pas d’obstacle entre les deux. Avertissement: • Rangez la pile dans un endroit hors de la portée des enfants afin d’éviter tout risque d’accident.
Pour commencer Ÿ Choisissez la source. Vous pouvez aussi choisir la source en... ⁄ Ajustez le son comme vous le souhaitez. (Voir les pages 24 et 25.) Opérations de base Pour couper le volume momentanément (ATT) Pour mettre l’appareil hors tension Précautions sur le réglage du volume: Les disques produisent très peut de bruit par rapport aux autres sources.
Annulation de la démonstration des affichages Si aucune opération n’est effectuée pendant environ 20 secondes, la démonstration des affichages démarre. [Réglage initial: Interval.]—voir page 30. Choisissez “Arret”. Quittez le réglage. Pour mettre en service la démonstration des affichages À l’étape 2, ci-dessus, choisissez “Toujours” ou “Interval.”.
Fonctionnement de la radio Choisissez “TUNER”. Ÿ Choisissez la bande (FM/AM). Démarrez la recherche d’une station. Quand une station est reçue, la recherche s’arrête. Pour arrêter la recherche, appuyez de nouveau sur la même touche. Écoute de la radio Pour accorder une station manuellement À...
Mémorisation des stations Vous pouvez prérégler six stations pour chaque bande. Préréglage automatique des stations FM —SSM (Mémorisation automatique séquentielle des stations puissantes) Choisissez la bande FM (FM1 – FM3) pour laquelle vous souhaitez mémoriser les stations. Les stations FM locale avec les signaux les plus forts sont recherchées et mémorisées automatiquement dans la bande FM.
Écoute d’une station préréglée Choisissez la station préréglée (1 – 6) souhaitée. • Maintenir pressée d’afficher la liste des stations préréglées (voir ci-dessous). Pour choisir une station préréglée en utilisant la liste des stations préréglées. Apparaît uniquement pour FM. Choisissez un numéro de préréglage. Liste des stations préréglées La liste montre la fréquence de la station ou le nom qui lui est affecté...
Utilisation du système FM RDS Recherche de votre programme FM RDS préféré Vous pouvez accorder une station diffusant votre programme préféré en effectuant une recherche par code PTY. • Pour mémoriser votre programme préféré, référez-vous à la page 13. Ÿ Choisissez un code PTY S’il y a une station diffusant un programme du code PTY que vous avez...
Mémorisation de vos programmes préférés Vous pouvez mémoriser six de vos types de programme préféré. Types de programme préréglés: Choisissez un code PTY. Choisissez un numéro de préréglage. Le code PTY choisi est mémorisé sur le numéro de préréglage choisi. Répétez les étapes à...
Pour mettre hors service l’attente de réception TA L’indicateur TP s’éteint. Attente de réception PTY L’attente de réception PTY permet à l’autoradio de commuter temporairement sur votre programme PTY préféré à partir de n’importe quelle source autre que AM. • Cette fonction affecte aussi le tuner DAB. Pour choisir votre code PTY préféré...
Utilisation du service de messages—Radiotexte RDS (RT) Qu’est qu’un Radiotexte RDS? Le Radiotexte RDS est une partie des données du signal RDS et permet de transmettre diverses informations (par ex. des informations sur le programme, numéros de téléphone, adresses électroniques et de site Web, informations sur l’artiste/titre et les titres des actualités).
Utilisation d’un disque ou d’une carte SD A propos des disques MP3 et WMA Les “plages” MP3 et WMA (Windows Media Audio) (les termes “fichier” ® et “plage” sont utilisés de façon interchangeable) sont enregistrées dans des “dossiers”. • Si un dossier MP3 ou WMA contient un fichier d’image <jll>...
Lecture de disques dans le changeur de CD À propos du changeur de CD Il est recommandé d’utiliser un changeur de CD JVC compatible MP3 avec votre autoradio. • Vous pouvez aussi connecteur un autre changeur de CD de la série CH-X (sauf le CH-X99 et le CH-X100).
À propos de la carte SD Vous pouvez reproduire des plages MP3/ WMA enregistrées sur une carte SD et afficher les images mémorisées sur l’affichage pendant la lecture—ImageLink. (Voir pages 16, 30 et 48 pour les détails.) Le format requis pour l’enregistrement sur une carte SD est FAT 12/16 et le volume recommandé...
Page 71
Si une carte SD est insérée... Le nom de l’album/interprète avec l’indicateur et le titre de la plage avec l’indicateur apparaissent si “Balise” est réglé sur “Activer” (voir page 32). Les écrans de commande utilisés pour les procédures suivantes sont ceux de la lecture d’un disque MP3 dans l’autoradio.
Pour choisir un disque pendant la lecture • Si vous maintenez pressé l’icône, la liste des disques apparaît sur l’affichage (voir la colonne de droite). Interdiction de l’éjection du disque Vous pouvez verrouiller un disque dans la fente d’insertion. “No Eject” clignote et le disque ne peut pas être éjecté.
Page 73
Si vous choisissez le dossier actuel (mis en valeur sur l’écran) sa liste des fichiers apparaît. • Choisissez une plage (uniquement pour les disques MP3/WMA ou les cartes SD). La liste des fichiers du dossier actuel apparaît. Apparaît uniquement si le disque actuel est un disque MP3.
Page 74
Ex.: Pour choisir la plage 32 lors de la lecture de la plage 6 dans le changeur de CD. * Si la source est “CD-CH”: Fonctionne uniquement quand un changeur de CD JVC compatible MP3 (CH-X1500) est connecté. (3 fois) La première fois que vous appuyez sur la touche “+10”...
Sélection des modes de lecture Vous pouvez utiliser un des modes de lecture suivants à la fois. Choisissez le mode de lecture souhaité. Mode Lecture des introductions Plage: Dossier* Disque* Arret: Mode Lecture répétée Plage: Dossier* Disque* Arret: Mode Lecture aléatoire Dossier* Disque ou SD: Toutes les plages du disque actuel ou de la carte SD.
Ajustements sonores Réglage du menu de sélection du son de base—SEL Ÿ Choisissez une option de réglage. Ajustez l’option choisie. A Pour ajuster la balance de sortie des enceintes entre les enceintes avant et arrière—FAD (fader). Pour ajuster la balance de sortie des enceintes entre les enceintes gauche et droite—BAL (balance).
Sélection des modes sonores préréglés (i-EQ: égaliseur intelligent) Vous pouvez choisir le mode sonore qui convient le mieux à votre genre de musique. Modes sonores disponibles FLAT (Aucun mode sonore n’est appliqué), HARD ROCK, R & B, POP, JAZZ, DANCE, COUNTRY, REGGAE, CLASSIC, USER 1, USER 2, USER 3 Choisissez un mode sonore.
Affichages graphiques Avant de commencer la procédure suivante, préparez un CD-R ou une carte SD avec des images fixes et des animations (séquences vidéo). • Avec Image Converter (Wide Ver 1.2) qui se trouve sur le CD-ROM fourni, vous pouvez créer vos propres images et animations.
Transfert d’une animation ou d’images • Il faut un certain temps pour télécharger une animation. Pour les détails, référez-vous à la page 49. • Pour activer les fichiers téléchargés, référez- vous à la page 29. À l’étape ! de la page 26... Apparaît uniquement si “IMAGE”...
Page 80
Apparaît uniquement si “IMAGE” est choisi. • Pour supprimer l’animation mémorisée Le nom du fichier apparaît. • Pour supprimer les images mémorisées Le nom du fichier apparaît. Répétez l’étape plus d’images. Quitter le réglage. pour supprimer Suppression de toutes les animations et images mémorisées •...
Activation des fichiers transférés • Pour activer les animations mémorisées pour les écrans d’ouverture et de fermeture 1 Choisissez “Ouverture” ou “Fin”. 2 Choisissez le réglage souhaité. Défaut: L’animation préréglée à l’usine est utilisée. Per so: Votre propre animation est utilisée.
Réglages généraux — PSM Procédure de base Vous pouvez changer les options PSM (mode des réglages préférés) de la table suivante. Choisissez une catégorie PSM. Vous pouvez passer à une catégorie différente en changeant simplement les réglages PSM. Indications Demo Démonstration des affichages Graphique...
Page 83
Indications ToucheCFM Animation Ouverture Écran d’ouverture Écran de fermeture Image Image personnelle Heures Heures Minutes Minutes 24H/12H Système de l’horloge Aj. Horloge Ajustement automatique de l’horloge Défi le Défilement Est affiché uniquement après qu’un fichier transféré est mémorisé. Est affiché uniquement après qu’un fichier transféré est mémorisé et que “Image” est choisi pour “Graphique”.
Page 84
Indications Assombrit Gradateur De – A Minuterie de gradateur Contraste Contraste Type LCD Type d’aff i chage Caractère Type de police de caractères Balise Aff i chage des balises Thème Indicateur de niveau sonore ToucheInf Limite des touches Sensibil. Sensibilité du panneau tactile Est affiché...
Page 85
Indications Attnt PTY Attente PTY AF-Rég Fréquence alternative/ réception régionale TA Volume Volume des informations routières Recherche Recherche de programme Filtre IF Filtre de fréquence intermédiaire DAB AF Recherche de fréquence alternative Annonce Attente d’annonce Dépend de la commande de gain de l’amplificateur. Est affiché...
Page 86
Français O (retour au début) • L’indication sur l’affichage apparaît aussi dans la langue choisie. Changer: [Réglage initial]; Pour utiliser un changeur de CD JVC, [17]. Ext In: Pour utiliser n’importe quel appareil extérieur, [39]. Sourdine1/Sourdine2: Choisissez le réglage qui permet de couper le son quand vous utilisez un téléphone...
Sélection du mode de gradateur Vous pouvez assombrir l’affichage la nuit ou au moment réglé dans la minuterie. Auto: Assombrit l’affichage quand vous allumez les feux. \ Allez à l’étape 9. Arret: Annulation. \ Allez à l’étape 9. Activer: Assombrit toujours l’affichage. \ Allez à...
Page 88
Choisissez la source. \ CD \ SD \ Changer Toute SRC* ) \ Line In \ FM \ AM (ou Ext In * \ DAB* \ (retour au début) Si vous choisissez “Toute SRC”, vous pouvez utiliser la même couleur pour toutes les sources.
Autres fonctions principales Affectation de titres aux sources Vous pouvez affecter des titres aux fréquences des stations, au CD (dans cet autoradio et dans le changeur de CD) et aux appareils extérieurs (LINE-IN et EXT-IN). Le nombre maximum de Sources CDs/CD-CH 32 caractères maximum (pour 30 des...
Changement de l’angle du Retrait du panneau de commande panneau de commande Lors du retrait ou de la fixation du panneau de commande, assurez-vous de ne pas endommager les connexion à l’arrière du panneau de commande et sur le porte-panneau. Retrait du panneau de commande Avant de retirer le panneau de commande, assurez-vous de mettre l’appareil hors tension.
Utilisation d’un appareil extérieur Vous pouvez connecter un appareil extérieur aux prises LINE IN à l’arrière—LINE-IN et un autre appareil à la prise du changeur de CD aussi à l’arrière en utilisant l’adaptateur d’entrée de ligne KS-U57 (non fourni)—EXT-IN. • Pour la connexion, référez-vous au Manuel d’installation/raccordement (volume séparé).
Fonctionnement du tuner DAB Choisissez “DAB”. Ÿ Choisissez la bande (DAB1/ DAB2/DAB3). Démarrez la recherche d’un ensemble. Quand un ensemble est reçu, la recherche s’arrête. Pour arrêter la recherche, appuyez de nouveau sur le même icône. ⁄ Choisissez le service (primaire ou secondaire) que vous souhaitez écouter.
Page 93
Il est recommandé d’utiliser le tuner DAB (Digital Audio Broadcasting) KT-DB1000 avec votre autoradio. Si vous possédez un autre tuner DAB, consultez votre revendeur autoradio JVC. • Référez-vous aussi aux Manuel d’instructions fournies avec votre tuner DAB. Quand les sons environnants sont bruyants...
Mémorisation de services DAB Vous pouvez prérégler 6 services DAB (primaires) pour chaque bande. Ex.: Mémorisation d’un ensemble (service primaire) sur le numéro de préréglage 1 de la bande DAB1. Choisissez un ensemble (service primaire). • Maintenir aussi d’afficher la liste des services préréglés (voir l’étape 5).
Changez le service si nécessaire. Utilisation de l’attente de réception Vous pouvez utiliser trois types d’attente de réception. • Attente de réception d’informations routières—attente de réception TA (voir ci- après). • Attente de réception d’annonce (voir la colonne de droite). •...
Pour mettre hors service l’attente de réception d’annonce Choisissez “ANN Arret” à l’étape 2 de la page L’indicateur ANN s’éteint. Attente de réception PTY L’attente de réception PTY permet à l’appareil de commuter temporairement sur votre programme PTY préféré à partir de n’importe quelle source sauf AM.
Entretien Comment nettoyer le panneau tactile Pour retirer les taches ou la poussière de la surface du panneau, mettez l’appareil hors tension, puis frottez avec un chiffon sec et doux. • Faites attention de ne pas rayer la surface en frottant.
Pour en savoir plus à propos de cet autoradio Opérations de base Généralités • L’horloge dans l’icône “RETOUR” sur l’écran fonctionne comme un indicateur de compte à rebours. Si aucune opération n’est faite pendant une certaine période de temps, l’écran actuel disparaît et l’écran de commande de la source revient.
Page 99
• Si un disque ou une carte SD est en place, choisir “CD” ou “SD” comme source de lecture démarre la lecture automatiquement. • Si une plage ou un dossier dont le nombre est supérieur à 99 est choisie, l’icône devant le nombre ( , ) disparaît (pour permettre l’affichage du nombre de 3...
Page 100
• Pour les disques MP3/WMA: Le nombre maximum de caractères pour les noms de fichier/dossier vraie selon le format du disque utilisé (et inclus les 4 caractères de l’extension—<.mp3> ou <.wma>). – ISO 9660 Level 1: 12 caractères maximum – ISO 9660 Level 2: 31 caractères maximum –...
Page 101
Mémorisation de vos propres modes sonores • Si vous ne souhaitez pas mémoriser l’ajustement actuel, mais seulement l’appliquer à la source de lecture actuelle, appuyez répétitivement sur “RETOUR” pour retourner à l’écran de commande de la source actuelle. L’ajustement réalisé reste actif jusqu’à...
Guide de dépannage Ce qui parait être un problème n’est pas toujours sérieux. Vérifiez les points suivants avant d’appeler un centre de service. Symptôme • L’écran disparaît soudainement. • Aucun son n’est entendu des enceintes. • Cet autoradio ne fonctionne pas du tout.
Page 103
Symptôme • Le son du disque est parfois interrompu. • “No Files” apparaît un instant sur l’affichage. • Du bruit est produit. • La durée de lecture écoulée n’est pascorrecte. • “Not Support” apparaît sur l’affichage et la plage est sautée.
Page 104
Symptôme • Le transfert semble ne jamais finir. • L’animation d’ouverture et de fermeture n’apparaît pas. • L’animation ne bouge pas. • L’animation n’a pas été transférée en entier. • Les réglages de la catégorie “VIDEO” n’ont aucun effet. • Vous ne pouvez pas choisir une image pour “Image”.
Spécifications SECTION DE L’AMPLIFICATEUR AUDIO Puissance de sortie maximum: Avant: 52 W par canal Arrière: 52 W par canal Puissance de sortie en mode continu (RMS): Avant: 19 W par canal pour 4 Ω, 40 Hz à 20 000 Hz avec moins de 0,8% de distorsion harmonique totale.