JVC TM-2703U User Manual

Color monitor/receiver

Hide thumbs Also See for TM-2703U:

User manual (40 pages)

User manual (41 pages)

Table Of Contents

Table of Contents

Quick Links

Download this manual

Color Monitor/Receiver Users Guide

��

�

��

�

��

Important Note:

In the spaces below, enter the model and serial number of your television (located at the

rear of the television cabinet). Staple your sales receipt or invoice to the inside cover of this

guide. Keep this user's guide in a convenient place for future reference. Keep the carton and

original packaging for future use.

Model Number:

Serial Number:

For Model TM-2703U

Illustration of TM-2703U and RM-C203

LCT1467-001A-A

0503-TN-II-IM

Table of Contents

Summary of Contents for JVC TM-2703U

Page 1: Important Note
Staple your sales receipt or invoice to the inside cover of this guide. Keep this user's guide in a convenient place for future reference. Keep the carton and original packaging for future use. Model Number: Serial Number: For Model TM-2703U Illustration of TM-2703U and RM-C203 LCT1467-001A-A 0503-TN-II-IM...
Page 2 5. In the event of trouble, unplug the unit and call a service technician. Do not attempt to repair it yourself or remove the rear cover. Changes or modifications not approved by JVC could void the warranty. • When you don’t use this TV set for a long period of time, be sure to disconnect both the power plug from the AC outlet and antenna for your safety.
Page 3 CAUTION ON REPLACABLE LITHIUM BATTERY The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 100ºC or incinerate. Replace battery with CR2032 Panasonic (Matsushita Electric) or Maxell is recommended.
Page 4 light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. ��...
Page 5 * Point the remote towards the remote sensor on the target component. The maximum operating distance is about 8 meters. * To operate a JVC VCR, use any of the following buttons: VCR POWER, TV/VCR INPUT, VCR CH+/-, PLAY, REWIND, FAST-FORWARD, STOP, RECORD and PAUSE.
Page 6: Table Of Contents
Table of Contents Quick Setup ... 7 Unpacking your TV ... . 7 Diagrams ....8 TV Remote Control .
Page 7: Quick Setup
Quick Setup Thank you for your purchase of a JVC Color Television. Before you begin setting up your new television, please check to make sure you have all of the following items. In addition to this guide, your television box should include: 1 Television ��...
Page 8: Diagrams
Quick Setup NOTE: Before you connect your television to another device, please refer to the proper diagrams for your specific TV and remote. These will help you in understanding how to connect your television to another device, as well as use the remote to set up your television.
Page 9: Tv Remote Control
Quick Setup • For information on remote control buttons, see pages 32 - 35. Remote Control �� ...
Page 10: Getting Started
The right and left buttons will turn the volume up or down. These buttons are also marked with four arrows and are used with JVC’s onscreen menu system. To use the onscreen menus, press the M button.
Page 11: Connecting Your Devices
Quick Setup Basic Operation Turn the television on and off by pressing the P of the remote. Step 2 – Connecting Your Devices Please follow the flow chart below to determine which connection setup is right for you. Then, refer to the appropriate diagrams to connect your television to other devices that you may have.
Page 12 Quick Setup Diagram #1 Note: • If you do not have a cable box, connect the cable wire directly from the wall outlet into the back of the TV. Diagram #2 �� Notes: • You must connect the video cable from the DVD player to the BNC connector box in order for it to work.
Page 13: Connecting To A Dvd Player
Quick Setup Diagram #3 �� Connecting to A DVD Player You can connect a DVD player instead of a VCR as illustrated in Diagram #2 on page 12 or Diagram #3 above. �� • You must connect the video cable from the DVD player to the BNC connector box in order for it to work.
Page 14: Connecting To A Camcorder
Quick Setup Connecting to an External Amplifier �� 1) Connect a white composite cable from the LEFT AUDIO OUTPUT on the back of the TV to the LEFT AUDIO INPUT on the amplifier. 2) Connect a red composite cable from the RIGHT AUDIO OUTPUT on the back of the TV to the RIGHT AUDIO INPUT on the amplifier.
Page 15: Auto Tuner Setup
Quick Setup Step 3 – Auto Tuner Setup JVC’s onscreen menu system lets you set your television up to meet your own personal viewing preferences. The menu screens and their features are discussed in detail in this book. The menu settings are optional, you can set as many or as few of them as you wish.
Page 16: Onscreen Menus
Onscreen Menus Using the Guide Certain symbols are used throughout this guide to help you learn about the features of your new television. The ones you will see most frequently are: π † Up and Down arrows mean press the C buttons let you: •...
Page 17: Initial Setup
Auto Tuner Setup If you have already run the Auto Tuner as part of the quick setup earlier in this guide, please skip ahead to “Channel Summary” to continue setting up your television. In Auto Tuner Setup, the TV automatically scans through all available channels, memorizing the active ones and skipping over blank ones or channels with weak signals.
Page 18: Channel Summary
Initial Setup Channel Summary Channel summary allows you to customize the line-up of channels received by your TV. You can add or delete channels from the line-up or prevent any unauthorized viewers from watching any or all 181 channels. Press the M button To CHANNEL SUMMARY π...
Page 19: V-Chip
V-Chip Your TV is equipped with V-Chip technology which enables you to block channels or content that you feel to be inappropriate for children, based on US and Canada rating guidelines. V-Chip has no effect on video signals from a DVD discs, VCR tapes or Camcorder connection. Note: Some programs, and movies are broadcast without a ratings signal.
Page 20 Initial Setup Unrated Programs Unrated programming refers to any programming which does not contain a rating signal. Programming on television stations which do not broadcast rating signals will be placed in the “Unrated Programming” category. Examples of Unrated programs: • Emergency Bulletins •...
Page 21 US V-Chip Ratings U.S. PARENTAL RATING SYSTEMS Programs with the following ratings are appropriate for children.  TV Y is Appropriate for All Children Programs are created for very young viewers and should be suitable for all ages, including children ages 2 - 6. ...
Page 22 Initial Setup Setting US V-Chip Ratings Press the M button To V-CHIP π † √® To operate (lock icon Press Z to access the V-Chip menu √® To turn V-Chip ON or OFF To move to SET US TV RATINGS π...
Page 23 Movies Ratings  NR – Not Rated This is a film which has no rating. In many cases these films were imported from countries which do not use the MPAA ratings system. Other NR films may be from amateur producers who didn’t intend to have their film widely released.
Page 24 Initial Setup Canadian V-Chip Ratings  E – Exempt Exempt programming includes: news, sports, documentaries and other information programming, talk shows, music videos, and variety programming.  C – Programming Intended for Children Violence Guidelines: There will be no realistic scenes of violence. Depictions of aggressive behavior will be infrequent and limited to portrayals that are clearly imaginary, comedic or unrealistic in nature.
Page 25: Set Lock Code
Set Lock Code Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes preset with a lock code of “0000”. You may change the code to any four-digit number you wish. To change the lock code, follow the steps below. Press the M button To SET LOCK CODE...
Page 26: Language
Initial Setup Language You can view the onscreen menu displays in one of three languages - English, French, or Spanish. You can use the language setting to change the menus to one of the other two languages if you wish. Press the M button To LANGUAGE...
Page 27: Front Panel Lock
Front Panel Lock This allows you to lock the keys on the front of the TV, so that a child may not accidentally change your viewing preferences. Press the M button To FRONT PANEL LOCK π † √® To turn ON or OFF Press the E button when finished You can turn off this feature in the following ways:...
Page 28: Picture Adjust
Picture Adjust Picture Settings These settings allow you to change and adjust the way the picture appears on your television. TINT Tint allows you to adjust the levels of red and green in your TV picture. COLOR The color function lets you make all the colors in the TV picture appear either more vivid or subtle.
Page 29: Sound Adjust
Sound Settings These settings allow you to change and adjust the way the sound is heard on your television. BASS – You can increase or decrease the level of low-frequency sound in the TV’s audio with the bass adjustment. TREBLE – Use treble to adjust the level of high-frequency sound in your TV’s audio. BALANCE –...
Page 30: Clock Timers
Clock/Timers Set Clock Before you use any of your TV’s timer functions, you must first set the clock. To set your clock, please follow the steps below. If you have XDS signal in your area, you can choose AUTO. Press the M button To SET CLOCK π...
Page 31: On/Off Timer
On/Off Timer The on/off timer lets you program your television to turn itself on or off. You can use it as an alarm to wake up, to help you remember important programs, or as a decoy when you’re not home. Press the M button To ON/OFF TIMER...
Page 32: Button Functions
124, press 100+, 2 (Two), 4 (Four). Menu The M button allows you to access JVC’s onscreen menu system. Press M the onscreen menu system. • See individual topics like “Sound Adjust” for specific information on using menus. Exit Use this button to enter or exit the TV’s onscreen menus.
Page 33: Return
Return + The R + button has two functions: ETURN Return - Returns to the channel viewed just before the channel currently onscreen. Return+ - Lets you program a specific channel to return to while scanning through the channels using the CH+ and CH– buttons. + and hold for three seconds ETURN The channel currently active has been programmed as your return+ channel.
Page 34: Display
Button Functions Display The display screen shows the current status of timers and inputs. Press the D ISPLAY The screen to the right shows the following information: • The current channel or AV input (Channel 05) • The current time (12:20 pm) •...
Page 35: Game
TV/VCR, power on, and power off. Move the selector switch to VCR to operate. • The remote is preset with the code 000 to control JVC-brand VCR’s. Button Functions �� ...
Page 36: Appendices
Troubleshooting �� ...
Page 37: Specifications
�� Specifications subject to change without notice. �� ...
Page 38: Notes
Notes...
Page 39 Notes...
Page 40 JVC PROFESSIONAL PRODUCTS COMPANY Division of JVC Americas Corp. 1700 Valley Road Wayne, New Jersey, 07470...

JVC TM-2703U User Manual

Quick Setup

Onscreen Menus

Initial Setup

Picture Adjust

Sound Adjust

Clock Timers

Button Functions

Appendices

Quick Links

Important Note:

Related Manuals for JVC TM-2703U

Summary of Contents for JVC TM-2703U

Table of Contents