(F) Cnu-700 - Sony BVP-900 Series Product Information Manual

10
Location and Function of Parts and Controls

(f) CNU-700

Front panel
CCU 1 through 6 connectors
2
Rear panel
1) POWER switch and indicator
Press to turn the power ON or OFF. The indicator illuminates when
power is switched on.
2) CCU (camera control unit) 1 through 6 connectors (8-pin)
Connect to the RCP/CNU REMOTE connector on a CCU-
700A/700AP Camera Control Unit using a CCA-5 cable.
3) RCP (remote control panel) 1 through 6 connectors (8-pin)
Connect to the CCU/CNU REMOTE connectors on an RCP-700
Series Remote Control Panel using a CCA-5 cable.
4) MSU (Master Set-up Unit) connector (8-pin)
Connect to the CCU/CNU REMOTE connector on an MSU-700
Master Set-up Unit using a CCA-5 cable.
5) VCS (video selector) connector (8-pin)
Connect to the REMOTE connector of a VCS-700 Video Selector
using a CCA-5 cable.
6) AUX1 and AUX2 (auxiliary 1 and 2) connectors (8-pin)
Connect to the AUX1 or AUX2 connector of another CNU-700 using a
CCA-5 cable when controlling multiple cameras with two or more
CNU-700 units. You can connect up to eight CNU-700 units.
7) CHARACTER 1and 2 connectors (BNC type)
Supply character data as a 525 or 625-line, black-and-white video
signal. The signal output is automatically selected according to the
reference signal input to the REFERENCE connector. If no reference
signal is input, the CNU-700 for the USA and Canada supplies a 525-
line video signal, the CNU-700 for other countries supplies a 625-line
79
POWER switch and indicator
1
POWER
3 RCP 1 through 6 connectors
CCU
1 2 3 4 5 6 1
7 8 9 10 11 12 7
CCU
CAMERACOMMAND NETWORK UNIT
4 MSU connector
VCS connector
5
6
RCP
MSU VCS AUX1
2 3 4 5 6
8 9 10 11 12 MSC VCS AUX3
~AC IN
10
9 RS-232C 1 through 3 connectors
REFERENCE connectors
8
CHARACTER 1 and 2 connectors
7
video signal. You can select whether to add a sync signal to the
output signal with switch S7 (SYNC ON/OFF) on the AT board.
Refer to the system manual for details on the board switch settings.
8) REFERENCE (reference signal input) loop connectors (BNC
type)
Accepts a reference signal (VS, BS, etc.). The signal output from the
CHARACTER connector is synchronized with the input signal.
9) RS-232C 1 through 3 connectors (D-sub 9-pin)
Used for RS-232C interfaces. The function of these connectors
depends on whether or not an optional BKP-7930 System Expansion
Board is installed in the CNU-700 as shown below.
Connector No. No BKP-7930 installed
1
2
3 Not used
10) ~AC IN (AC power input) connector
Connect to an AC power source using the supplied AC power cord.
The power cord can be fixed to the CNU-700 using the supplied plug
holder.
11) Optional board insertion section
Used for attaching the connector panel of an optional BKP-7930/7933.
When you attach the BKP-7930 to the CNU-700, up to 12 cameras
and remote control panels can be controlled. BKP-7933 enables the
S-bus functionality.
AUX1 and AUX2 connectors
AUX2
AUX4
11 Optional board insertion
section
~AC IN connector
With BKP-7930 installed
Reserved for ISR system
Reserved for RS-232C interface
Reserved for RS-232C system