Sharp PG-M20X Service Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Projector
  5. Notevision PG-M20X
  6. Service manual
Sharp PG-M20X Service Manual

Sharp PG-M20X Service Manual

Digital multimedia projector
Hide thumbs Also See for PG-M20X:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.
Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen
Originalzustand gebracht werden. Außerdem dürfen für die spezifizierten Bauteile nur identische Teile verwendet
werden.
CONTENTS
» SPECIFICATIONS ............................................. 2
NOTES (for USA) ............................................... 3
» NOTE TO SERVICE PERSONNEL ................... 4
» OPERATION MANUAL ...................................... 7
» REMOVING OF MAJOR PARTS ..................... 13
» ELECTRICAL ADJUSTMENT ........................... 19
» TROUBLE SHOOTING TABLE ........................ 25
» CHASSIS LAYOUT .......................................... 46
» BLOCK DIAGRAM ........................................... 48
» OVERALL WIRING DIAGRAM ........................ 50
» SCHEMATIC DIAGRAM .................................. 52
Ë ELECTRICAL PARTS ................................ 103
Ë ACCESSORIES PARTS ............................ 120
Ë PACKING PARTS ....................................... 120
» PACKING OF THE SET ................................. 121

SHARP CORPORATION

TENTATIVE
SERVICE MANUAL
SERVICE-ANLEITUNG
DIGITAL MULTIMEDIA PROJECTOR
DIGITALER MULTIMEDIA PROJEKTOR
MODEL
MODELLE
Page
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
PG-M20X
PG-M20X

Advertisement

Table of Contents
loading

Related Manuals for Sharp PG-M20X

Summary of Contents for Sharp PG-M20X

  • Page 1: Table Of Contents

    PG-M20X TENTATIVE SERVICE MANUAL SERVICE-ANLEITUNG DIGITAL MULTIMEDIA PROJECTOR DIGITALER MULTIMEDIA PROJEKTOR MODEL PG-M20X MODELLE In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.

  • Page 2: Specifications

    Terminal cover (GCOVD0103CESA), CD-ROM (UDSKA0058CEN1), Operation manual (TINS-7609CEZZ), Quick reference guides This SHARP projector uses a DMD panel. This very sophis- This unit has some inactive pixels within acceptable toler- ticated panel contains 786,432 pixels. As with any high tech- ances which may result in inactive dots on the picture screen.

  • Page 3: Important Service Safety Notes (For Usa)

    PG-M20X IMPORTANT SERVICE SAFETY NOTES (for USA) Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm WARNING per volt., or higher, sensitivity to measure the AC...

  • Page 4: Note To Service Personnel

    PG-M20X NOTE TO SERVICE NOTE POUR LE PERSONNEL PERSONNEL D’ENTRETIEN 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5...

  • Page 5: Lamp Replacement

    éviter une exposition des yeux et la peau (Fig. 1). Note: Please obtain a lens cap before servicing a Remarque: Priére de se procurer un capuchon models PG-M20X that is received without d'optique acant d'entretien un modéle one. PG-M20X qui est livré sans.
  • Page 6 PG-M20X WARNING: High brightness light source, do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly in to the beam of light. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO MOISTURE OR WET LOCATIONS.
  • Page 7 PG-M20X Precautions for using lead-free solder 1 Employing lead-free solder "Main PWB" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.

  • Page 8: Location Of Controls

    PG-M20X Location of Controls Projector (Front and Top View) TEMPERATURE LAMP REPLACEMENT WARNING indicator indicator Illuminates in green Illuminates in green normally. normally. When the Replace the lamp when the internal temperature indicator illuminates in red. rises, this indicator will POWER indicator illuminate in red.
  • Page 9 PG-M20X Projector (Side View) INPUT 1 terminal USB terminal For connecting a compu- Port for DVI digital, computer RGB, and COMPONENT ter using a USB cable. signals. INPUT AUDIO terminal INPUT 2 terminal Shared audio terminal for Terminal for connecting video...

  • Page 10: Remote Control

    PG-M20X Remote Control Remote control signal transmitter FORWARD/BACK button POWER button Moves forward or backwards Turns the power on or off. when connected to a computer using a USB cable. Same as the ENLARGE (Enlarge/Reduce) [Page Down] and [Page Up] buttons keys on a computer keyboard.

  • Page 11: Connection Pin Assignments

    PG-M20X Connection Pin Assignments DVI Digital / Analog INPUT 1 port : 29 pin connector • DVI Digital INPUT Pin No. Signal Pin No. Signal • • • • • • • • • • • • • • • • • •...
  • Page 12 PG-M20X Dimensions Rear View Side View Top View Side View (318.3) (302.5) (223) (219) (128) Front View (38.7) (76.1) (82.9) (34.2) (115.5) (195) (82.5) (55.5) (60) (80) (7.5) Bottom View (104) (261.5) Units: inches (mm)

  • Page 13: Removing Of Major Parts

    PG-M20X REMOVING OF MAJOR PARTS 1. Removal of the top body 1-1. Detach the terminal block cover. 1-2. Remove the five lock screws from the top body. 1-3. Slightly lift the front of the top body and disconnect the speaker connector.
  • Page 14 PG-M20X 3. Removal of the PC I/F PWB and input PWB 3-1. Disconnect the specified connectors. 3-2. Remove the three lock screws and two hex screws from the PC I/F PWB. 3-3. Disconnect the connector from the input PWB. 3-4. Remove the three lock screws from the input PWB.
  • Page 15 PG-M20X 4. Removal of the operation PWB, optical unit and ballast unit 4-1. Disconnect the specified connectors from each PWB. 4-2. Remove the two lock screws from the operation PWB. 4-3. Remove the six lock screws from the optical unit.

  • Page 16: Resetting The Total Lamp Timer

    • Cooling fan break- • Take the projector to your nearest TURE temperature is Red on/ WARNING down Sharp Authorized Projector Dealer abnormally high. Power off • Internal circuit failure indicator or Service Center for repair. • Clogged air intake •...

  • Page 17: Caution Concerning The Lamp

    • Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit. If the new lamp does not light after replacement, take your projector to the nearest Sharp Autho- rized Projector Dealer or Service Center for repair. Purchase a replacement lamp unit of type BQC- PGM20X//1 from your nearest Sharp Authorized Projector Dealer or Service Center.
  • Page 18 PG-M20X How to Release the System Lock Turn on the power. If the system lock is applied, the system-resetting screen appears. Press the following keys in this order. MENU → ENTER → ENTER → MENU → UNDO → UNDO → MENU...

  • Page 19: Electrical Adjustment

    PG-M20X ELECTRICAL ADJUSTMENT Adjustment Items Adjustment Conditions Adjustment Procedures Initialization of 1. Turn on the power (the lamp lights 1. Carry out the following setting. EEPROM up) and warm up the system for 15 Press SW2001 to enter the process minutes.
  • Page 20 PG-M20X Adjustment Items Adjustment Conditions Adjustment Procedures Adjustment of 1. Feed the internal 8ch (split color bar) 1. Confirm the fixed value. NTSC color signal. Fixed value: 59 saturation 2. Select the following group and sub- ject. Group: VIDEO Subject: N-COLOR Adjustment of PAL 1.
  • Page 21 Confirmation of 1. Receive monoscope pattern signal. 1. Select L2 in the process mode. picture-related Check Picture, Brightness and Sharp- operation ness. Confirmation of 1. Receive the RGB signal. 1. Select L4 on the process mode. Check Picture, Brightness, Red, Blue, Clock, Phase, H-POS and V-POS.
  • Page 22 PG-M20X Adjustment Items Adjustment Conditions Adjustment Procedures Automatic sync 1. Receive the phase checking pattern 1. Confirm that Clock, Phase, H-POS operation signal. and V-POS can be automatically adjusted in the VGA/S-VGA/XGA mode. Confirmation of Connect the set to a personal computer...
  • Page 23 PG-M20X » Adjustment mode process menu Group Sub Group Subject Adjust PC Image R-BRIGHT G-BRIGHT B-BRIGHT AD-AUTO Adjust DLP Image R1-BLK R1-GAIN G1-BLK G1-GAIN B1-GAIN CW-INDEX S-R1-GAIN S-G1-GAIN S-B1-GAIN C-R1-GAIN C-B1-GAIN V-R1-GAIN V-B1-GAIN Adjust VIDEO Image VIDEO PICTURE BRIGHT TINT...
  • Page 24 PG-M20X Group Sub Group Subject Adjust CVIC CVIC-PROGRSSIVE MODE MDSW PTGSW C-TESTSW C-ILG-LY C-MOD-LY C-VE-LV CVIC-ENHANCE-VIDE ENH-PLUS ENH-MINUS CVIC-ENHANCE-HTTV ENH-PLUS ENH-MINUS CVIC-ENHANCE-RGB ENH-PLUS ENH-MINUS CVIC-SCREEN CUBIC-RGB CUBIC-VEDEO CVIC-NR YNR-LEVEL YNR-K YNR-FSEL CNR-LEVEL CNR-K CNR-FSEL CNR-FILSW CVIC-PTG TBL-NO CVIC-CMS YELLOW GREEN...

  • Page 25: Trouble Shooting Table

    PG-M20X TROUBLE SHOOTING TABLE Checking of Basic Operation Does the POWER LED light up or Go to "Checking of Power Unit". flicker in red or green? Does the set operate by the set's Go to "Checking of Sub-microcomputer key or the remote controller's and Its Periphery"...
  • Page 26 PG-M20X Checking of Power Unit Insert the connectors CN702, Are connectors in the power unit CN704, CN7003, CN7001, completely inserted? CN7004 and CN7101 completely. Close the lamp door completely by Is the lamp door closed screws. completely? Replace the bimetal switch, or rest Is the bimetal switch turned off? it by pressing the red button.
  • Page 27 PG-M20X Lamp Does Not Light Up. Is any of SC9001, SC9002, P9002 and P9003 connectors Insert the connectors completely. disconnected or in poor contact? Is an appropriate voltage supplied Go to "Checking of Input PWB" to SC9002? Is there the 180-Hz pulse signal at Go to "Checking of Lamp"...
  • Page 28 PG-M20X Lamp does not light up. Check the power circuit or the fan Is the cooling fan rotating? circuit on the key/input PWB. Check IC3101, the motor driver Is the color wheel rotating sound circuit and their periphery. heard? Check the waveform of SC3101.
  • Page 29 PG-M20X Checking of Sub-microprocessor and Its Periphery Does POWER LED flicker in red (for 2 seconds)? Go to "Checking of PC I/F Unit", and check the flexible connector. Is there B+3.3V output at pins (12) Communication error of sub-microprocessor and (13) of CN3701? (KEY) and SH microprocessor (PC I/F unit) Pins (20) and (21) of P2001.
  • Page 30 PG-M20X Checking of Low-pass Filter Circuit Is video signal is inputted to pins Check pins (4), (8) and (12) of (4), (8) and (12) of IC3851? SC3001. Normal Abnormal Check the PC I/F unit. Check Q3854 and Check DVI (analog) Q3855.
  • Page 31 PG-M20X Checking of DTV (480i Component Input) Feed the 480i component signal in INPUT 1. Select INPUT 1 using the set's key or the remote controller. Go to "Checking of Select 480i among the special modes on the user Low-pass Filter Circuit"...
  • Page 32 PG-M20X Checking of Video Input Feed the composite video signal to INPUT 3. Select INPUT 3 using the set's key or the remote controller. Are pin(5) (horizontal) and pin(10) (vertical) signals Does the picture appear? Is the picture disturbed? inputted to IC8363 on the...
  • Page 33 PG-M20X » FORMATTER Unit Abnormal picture Blackout Others Rainbow-like picture Go to "Lamp Does Not Is the lamp on? Light Up." Is signal outputted at Go to "Checking of PC I/F nunit" pins (3), (5) and (7) of SC9001? Trouble with IC9003,...
  • Page 34 PG-M20X » PC I/F Unit-1/12 Checking of PC PWB Is the user menu displayed? Check the onscreen display. Check the RGB input. Check the component input. Check the video input. Check the DVI digital input. Check the PC card.
  • Page 35 PG-M20X » PC I/F Unit-2/12 Checking of Onscreen Display Is the user menu displayed The onscreen display is normal. normally by the MENU key? Enter the process menu and select PATTERN. Then select the COLOR pattern. Adjust the DLP system in the Is the onscreen display color process adjustment mode.
  • Page 36 PG-M20X » PC I/F Unit-3/12 Checking of RGB Input Feed the sync separation type analog RGB signal to INPUT 1. Select INPUT 1 using the set's key or the remote controller. Go to "Confirmation of Does the picture appear? Video Input".
  • Page 37 PG-M20X » PC I/F Unit-4/12 Confirmation of Video Input Make "Confirmation of Input Signal Setting". Is there signal at the terminal C2 of Is there video signal at the land P8001 (DVI connector)? of C8070? Somewhere in the signal route is Go to "Checking of Sync Signal".
  • Page 38 PG-M20X » PC I/F Unit-5/12 Checking of Sync Signal Is there the vertical sync signal at pin (11) of IC8363? Is there the horizontal sync signal Make confirmation of input signal at pin (5) of IC8363? setting. IC8330, IC8331 or its periphery is defective.
  • Page 39 PG-M20X » PC I/F Unit-6/12 Checking of R, G and B Signals Is the signal type set to RGB? Set the signal type to RGB. Set the process mode. Select R, G and B individually on the pattern menu. Go to "Checking of GA4 and Its Periphery".
  • Page 40 PG-M20X » PC I/F Unit-7/12 Checking of GA4 and Its Periphery Select R, G and B individually on the pattern menu in process mode. Checking of GA4 and its periphery Is picture outputted appropriately ends. in R, G and B? Check pins (72), (52) and (32) of SC8001 by oscilloscope.
  • Page 41 PG-M20X » PC I/F Unit-8/12 Checking of Component Input (except 480I) Feed the component signal to INPUT 1. Select INPUT 1 using the set's key or the remote controller. Is the picture appear? Go to "Checking of SOG Circuit". Is the color normal? Is the signal type set at component? Set the signal type to component.
  • Page 42 PG-M20X » PC I/F Unit-9/12 Checking of SOG Circuit Check pin (2) of IC8365 by oscilloscope. Is the composite sync signal The SOG circuit is normal. reproduced in correct timing? End. Check the land of C8070 by oscilloscope. Is there the Y signal including sync Go to "Confirmation of Input...
  • Page 43 PG-M20X » PC I/F Unit-10/12 Checking of Video Input Feed the composite video signal to INPUT 3. Select INPUT 3 using the set's key or the remote controller. Go to "Checking of Video Is the picture appear? Sync Signal". Is there any disturbance in the picture? Go to "Checking of Video...
  • Page 44 PG-M20X » PC I/F Unit-11/12 Checking of Video Sync Signal Check pin (10) of IC8363 by oscilloscope. (Checking of vertical sync signal) Is the vertical sync signal normal? Check pin (6) of IC8363 by oscilloscope. (Checking of horizontal sync signal) Is the horizontal sync signal Go to "Confirmation of Input Signal...
  • Page 45 PG-M20X » PC I/F Unit-12/12 Checking of DVI Digital Input Feed the DVI digital signal to INPUT 1. Select INPUT 1 for input. Is the picture appear? Is there any disturbance in the picture? IC8298 and its periphery are Is the color normal? defective.

  • Page 46: Chassis Layout

    PG-M20X CHASSIS LAYOUT...

  • Page 47: Block Diagram

    PG-M20X BLOCK DIAGRAM Rod Antenna IC 2002 KEY UNIT Filter IC 5801 Reset Reg. 455kHz RF_ON FM Receiver SYN_ENE,DATA,CLK BU6V POWER UNIT Filter ANT_49 PCON 0 FANERROR STREAM_A_CLK,DATA IC 5803 PCON 1 FANPOW FAN1 IC 3201 Packet Flaming STATUS,USB_PWR Reg.

  • Page 48: Overall Wiring Diagram

    PG-M20X OVERALL WIRING DIAGRAM...

  • Page 49: Description Of Schematic Diagram

    PG-M20X DESCRIPTION OF SCHEMATIC BESCHREIBUNG DES DIAGRAM SCHEMATISCHEN SCHALTPLANS VOLTAGE MEASUREMENT CONDITION: SPANNUNGSMESSUNGEN: 1. Spannungen an den Prüfpunkten werden bei einer 1. Voltages at test points are measured at the supply Netzspannung von 230V gemessen, Signale werden voltage of AC 230V. Signals are fed by a colour bar für die Wartung mit einem Farbbalken-Signal...
  • Page 50 PG-M20X WAVEFORMS 1 SC3101 1-pin 2 SC3101 3-pin 3 P9002 1-pin 4 P9003 2-pin (INPUT CWCTR) (INPUT CWY2) (FORMAT LAMPEN) (FORMAT CWINDEX) H : 200µ sec/div H : 200µ sec/div H : 2m sec/div H : 2m sec/div V : 6.90V/div V : 6.90V/div...
  • Page 51 PG-M20X Ë FORMATTER UNIT-1/5...
  • Page 52 PG-M20X Ë FORMATTER UNIT-2/5...
  • Page 53 PG-M20X Ë FORMATTER UNIT-3/5...
  • Page 54 PG-M20X Ë FORMATTER UNIT-4/5...
  • Page 55 PG-M20X Ë FORMATTER UNIT-5/5...
  • Page 56 PG-M20X Ë INPUT UNIT-1/5...
  • Page 57 PG-M20X Ë INPUT UNIT-2/5...
  • Page 58 PG-M20X Ë INPUT UNIT-3/5...
  • Page 59 PG-M20X Ë INPUT UNIT-4/5...
  • Page 60 PG-M20X Ë INPUT UNIT-5/5...
  • Page 61 PG-M20X Ë KEY UNIT-1/3...
  • Page 62 PG-M20X Ë KEY UNIT-2/3...
  • Page 63 PG-M20X Ë KEY UNIT-3/3...
  • Page 64 PG-M20X Ë POWER UNIT...
  • Page 65 PG-M20X Ë PFC UNIT...
  • Page 66 PG-M20X Ë PC I/F UNIT-1/7...
  • Page 67 PG-M20X Ë PC I/F UNIT-2/7...
  • Page 68 PG-M20X Ë PC I/F UNIT-3/7...
  • Page 69 PG-M20X Ë PC I/F UNIT-4/7...
  • Page 70 PG-M20X Ë PC I/F UNIT-5/7...
  • Page 71 PG-M20X Ë PC I/F UNIT-6/7...
  • Page 72 PG-M20X Ë PC I/F UNIT-7/7...

  • Page 73: Printed Wiring Board Assemblies

    PG-M20X PRINTED WIRING BOARD ASSEMBLIES PC I/F Unit (Side-A)
  • Page 74 PG-M20X PC I/F Unit (Side-B)
  • Page 75 PG-M20X FORMATTER Unit (Side-A) INPUT Unit (Side-A) KEY Unit (Side-A)
  • Page 76 PG-M20X FORMATTER Unit (Side-B) INPUT Unit (Side-B) KEY Unit (Side-B)
  • Page 77 PG-M20X POWER Unit (Side-A) POWER Unit (Side-B) PFC Unit (Component Side)

  • Page 78: Parts List

    Contact your nearest SHARP Parts Distributor. For location of SHARP Parts Distributor, 5. KODE 6. QUANTITÄT Please call Toll-Free; 1-800-BE-SHARP in CANADA: Contact SHARP Electronics of Canada Limited Phone (416) 890-2100. MARK: SPARE PARTS-DELIVERY SECTION MARKIERUNG : ERSATZTEILE-LIEFERUNG Ref. No.
  • Page 79 PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code C9510 VCKYCY1EF104Z J 0.1 Ceramic DUNTKB065DE01 C9511 VCKYCY1EF104Z J 0.1 Ceramic C9513 VCKYCY1EF104Z J 0.1 Ceramic FORMATTER UNIT(Continued) C9514 VCKYCY1EF104Z J 0.1 Ceramic C9515 VCKYCY1EF104Z J 0.1...
  • Page 80 PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code R9564 VRS-CY1JF562J J 5.6k 1/16W Metal Oxide DUNTKB066DE01 R9565 VRS-CY1JF103J J 10k 1/16W Metal Oxide R9566 VRS-CY1JF821F J 820 1/16W Metal Oxide INPUT UNIT R9567 VRS-CY1JF121F J 120 1/16W Metal Oxide R9569 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide...
  • Page 81 PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code C3106 VCEASM1HW105M J 1.0 Electrolytic DUNTKB066DE01 C3107 VCKYCY1HB102K J 1000p 50V Ceramic C3109 VCKYCY1EF104Z J 0.1 Ceramic INPUT UNIT C3110 VCKYCY1HF224Z J 0.22 Ceramic C3111 VCKYCY1EF104Z J 0.1...
  • Page 82 PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code R3516 VRS-CY1JF562J J 5.6k 1/16W Metal Oxide DUNTKB066DE01 R3522 VRS-CY1JF122J J 1.2k 1/16W Metal Oxide R3526 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide INPUT UNIT (Continued) R3528 VRS-CY1JF562J J 5.6k 1/16W Metal Oxide...
  • Page 83 PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code C2104 VCKYCY1EF104Z J 0.1 Ceramic DUNTKB067DE01 C2105 VCKYCY1EF104Z J 0.1 Ceramic C2106 VCEASM1CW107M J 100 Electrolytic KEY UNIT C2108 VCEASM1EW336M J 33 Electrolytic C2109 VCEASM1EW336M J 33...

  • Page 84: Power Unit

    PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKB067DE01 RDENCA004WJZZ KEY UNIT (Continued) POWER UNIT INTEGRATED CIRCUITS R2202 VRS-CB1JF102J J 1.0k 1/16W Metal Oxide R2203 VRS-CY1JF103J J 10k 1/16W Metal Oxide IC7101 0H1Q3A0010 TA76431 R2204 VRS-CB1JF103J...
  • Page 85 PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code RDENCA004WJZZ RDENCA010WJZZ POWER UNIT (Continued) PFC UNIT INTEGRATED CIRCUITS C7451 0C195E4730 0.047 50V Ceramic C7452 0C195E1040 Ceramic IC701 H3151AC001 FA5502M C7453 0C195E1040 Ceramic IC702 0H1R1A0010 MIP0254SPSCF C7454 0C1Q1E2210...
  • Page 86 PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code R791 0R390T8230 82k 1/4W Chip3216 RDENCA010WJZZ R792 0R390T8230 82k 1/4W Chip3216 R793 0R390T8230 82k 1/4W Chip3216 PFC UNIT (Continued) R7466 0R3Q4S6810 680 1/16W Chip1608 R7467 0R3Q4S1020 1/16W Chip1608...
  • Page 87 PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code 9DK001-81062 BLM21P221SG CPCi-0057CE01 9DK001-81052 NLC322522T-3R3M 3.3uH 9DK001-81052 NLC322522T-3R3M 3.3uH PC I/F UNIT 9DK001-81062 BLM21P221SG 9DK001-81052 NLC322522T-3R3M 3.3uH INTEGRATED CIRCUITS 9DK001-81062 BLM21P221SG 9DK001-11020 AT24C128N-10SC-1.8 9DK001-81044 BLM21B201S 9DK001-15115 PQ05VY3H3Z...
  • Page 88 PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code C447 9DK001-42131 Ceramic CPCi-0057CE01 C448 9DK001-42122 180p 50V Ceramic C449 9DK001-42122 180p 50V Ceramic PC I/F UNIT (Continued) C450 9DK001-42122 180p 50V Ceramic C454 9DK001-42131 Ceramic 9DK001-40081 6.3V...
  • Page 89 PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code 9DK001-50149 1/16W Chip CPCi-0057CE01 9DK001-50149 1/16W Chip 9DK001-50 1.07k 1/16W Chip1608 PC I/F UNIT (Continued) 9DK001-50213 2.0k 1/16W Chip1608 9DK001-50181 3.3k 1/16W Chip1608 C697 9DK001-42 Ceramic 9DK001-50181 3.3k 1/16W Chip1608...
  • Page 90 PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0057CE01 PC I/F UNIT (Continued) R688 9DK001-50201 1/16W Chip1608 R689 9DK001-50173 470 1/16W Chip1608 R690 9DK001-50205 1.8k 1/16W Chip1608 R692 9DK001-50159 1/16W Chip1608 R693 9DK001-50159 1/16W Chip1608...

  • Page 91: Ë Cabinet And Mechanical Parts

    PG-M20X CABINET AND MECHANICAL PARTS 1-1-7 1-12 1-1-8 1-1-4 1-1-3 1-1-10 1-1-6 2-3-3 2-3-2 2-2-5 2-1-1 2-1-5 2-2-9 2-1-4 2-1-2 2-2-2 2-1-3 2-2-4...
  • Page 92 PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code NSFTZ0170CEFW J Hexagon Screw, x3 NSFTZ0183CEFW J Hexagon Screw, x2 CABINET AND MECHANICAL PARTS PSLDM4719CEFW J Terminal Shield QEARPA033WJFW Earth Angle PSPAT0013CEZZ J Tape, x14 Not Available –...
  • Page 93 PG-M20X OPTICS MECHANISM PARTS 6-48 6-57 6-48 6-51 6-13 6-35 6-45 6-46 6-52 6-21 6-18 6-12 6-20 6-16 6-21 6-30 6-17 6-50 6-28 6-22 6-34 6-27 6-15 6-10 6-24 6-36 6-23 6-25 6-29 6-30 6-31 6-36 6-56 6-43 6-40 6-41...
  • Page 94 PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code OPTICS MECHANISM PARTS CCHSK0106CE01 Optics Engine Ass'y 10A1018602 Optics Engine PLNS-0243CEZZ Projection Lens CLMPFA001CE01 Lamp Case Ass'y Screw, x4 RMOTBA001WJZZ Color Wheel Color Wheel Fixing Angle Screw, x3...

  • Page 95: Ë Packing Parts

    PG-M20X Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING PARTS SUPPLIED ACCESSORIES (NOT REPLACEMENT ITEM) CCAPHA001WJ01 Lens Cap SPAKAA015WJZZ – Partation Board — GCASN0005CESA J Carrying Bag SPAKC5669CEZZ – Packing Case — GCOVD0103CESA J Terminal Cover SPAKF0552CEZZ –...

  • Page 96: Packing Of The Set

    PG-M20X PACKING OF THE SET Carrying Bag (GCASN0005CESA) Terminal Cover (GCOVD0103CESA) Power Cord (for U.K., Hong Kongand Singapore) (QACCB5024CENA) Power Cord(for U.S., Canada) (QACCDA007WJPZ) Power Cord(for Australia,New Zealand and Oceania) Sleeve (QACCL3022CEZZ) Power Cord(for Europe) (SPAKCF0552CEZZ) (QACCV4002CEZZ) USB Cable (QCNWG0001WJPZ)
  • Page 97 PG-M20X COPYRIGHT © 2002 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Table of Contents