Picutre Mode - Pioneer PDP-502MX Service Manual

PDP-502MX, PDP-502MXE
Items to adjust and set value in Each Adjustment mode

PICUTRE mode

PICTURE mode has three menus, "REFERENCE 1", "REFERENCE 2" and "VIDEO
BOX".
Press "1" key on the remote control unit to enter "REFERENCE 1", press "2" key on the
remote control unit to enter "REFERENCE 2" and press "3" key on the remote control unit
to enter "VIDEO BOX". For "VIDEO BOX" mode , refer to the service manual ARP3038
for PDA-5001/ZYVLPK
Do not operate keys that have no parameters applied to the current input signal mode.
REFERENCE 1 mode
Adjustment mode independent of input signal format / Data stored in EEPROM of U-COM ASSY
Remote
Adjustment
Control
Parameter
Key
1 CONTRAST
2 BRIGHT
3 COLOR
4 TINT
H. SHARP
5
H. ENHANCE
6 DETAIL
7 R HIGH
8 G HIGH
9 B HIGH
10 R LOW
11 G LOW
12 B LOW
V. SHARP
BS5
V. ENHANCE
BS9 ABL LEV OFFSET ABL Level offset adjustment
BS11 PLS NUM OFFSET Pulse number offset adjustment
REFERENCE 2 mode
Adjustment mode independent of input signal format / Data stored in EEPROM of VIDEO ASSY
Remote
Adjustment
Control
Parameter
Key
1 R-Y/R
2 R-Y/B
3 G-Y/R
4 G-Y/B
9 ENHANCER MAIN
10 ENHANCER V
11 ENHANCER M
12 ENHANCER H
BS5 R-Y LEVEL
BS7 B-Y LEVEL
BS9 Y DELAY
BS11 CTI LEVEL
Note 1) For Parameter , adjustment values are fixed.
Note 2) If unnecessarily adjusted, power consumption of the unit is changed and the panel is damaged.
Adjust only in case of necessity.
50
Adjusting & Setting Item
Contrast adjustment
Brightness adjustment
Color adjustment
Tint adjustment (C.Video signal input only)
Horizontal sharpness setting (Video signal input) 128 140 140 128 128 140 113 128 128 128 128 128 ––
Horizontal sharpness setting (PC signal input)
Detail setting
White Balance adjustment
Vertical sharpness setting (Video signal input)
Vertical sharpness setting (PC signal input)
Adjusting & Setting Item
Matrix demodulation angle setting
(Video signal input only)
Sharpness setting
Color-difference adjustment
(INPUT 1, 2 only)(502MX only)
Y delay setting (INPUT 1, 2 only)(502MX only)
Color transient setting (INPUT 1, 2 only)
R E F E R E N C E 1
Adjustment parameter
C O N T R A S T
Setting Value
C. VIDEO/YC SCART RGB COMPONENT
NTSC PAL SECAM 4.43NT RGB60RGB50 STD × 2 HDTV STD × 2 HDTV
Adjustment required
Adjustment required
–– –– –– –– –– ––
128 128 128 128 128 128 128 128 128 128 128 128 128
Adjustment required
128 140 140 128 128 140 113 128 128 128 128 128 ––
–– –– –– –– –– ––
Adjustment required (note 2)
8 8 8 8 8 8
Setting Value
C. VIDEO/YC SCART RGB COMPONENT
NTSC PAL SECAM 4.43NT RGB60 RGB50 STD × 2 HDTV STD × 2 HDTV
6(10) 11(13) 11(13) 6(10) 10 13
12(15) 14(15) 14(15) 12(15) 15 15
7 9(10) 9(10) 7 10 10
8 6(4) 6(4) 8 5 4
0(0) 0(0) 0(0) 0(0) 0 0
0(0) 0(0) 0(0) 0(0) 0 0
0(0) 0(0) 0(0) 0(0) 0 0
0(0) 0(0) 0(0) 0(0) 0 0
–– ––
Adjustment required
–– ––
1 0 3 4 –– ––
1(2) 2 2 2 2 2
SCART RGB: PDP-502MXE Only, (
Current menu
Input signal
M O D E 0 6 – A / N
Setting value
: 1 6 0
RGB VIDEO
PC
–– –– –– –– –– –– 128
–– –– –– –– –– –– 128
8 8 8 8 8 8
SCART RGB: PDP-502MXE Only
RGB VIDEO
PC
6 6 6 6 6 6 ––
12 12 12 12 12 12 ––
7 7 10 7 7 10 ––
8 8 5 8 8 5 ––
0 0 0 0(0) 0(0) 0 ––
0 0 0 0(0) 0(0) 0 ––
0 0 0 0(0) 0(0) 0 ––
0 0 0 0(0) 0(0) 0 ––
–– –– –– –– –– –– ––
–– –– –– –– –– –– ––
–– –– –– –– –– –– ––
–– –– –– –– –– –– ––
): PDP-502MXE
8